Tommy

k2thestank

Slider version now live and available Test prints have been successful and are now good to go. If you encounter any issues please let me know!&nbsp;<ul><li>still working on the minor accessories to match the sliding version as it was a complete model rebuild to accommodate them into the old/previous model (will be released in the corresponding folder here)</li><li>Adapting a backplate mechanism to help secure it onto the P1P as they don't have a stable way to attach to the top</li><li>Testing of 2812B LED strips with a BT 5v usb adapter and connectors or seperate power supply unsure of which will work best</li><li>adapting the Backer into a more robust case enclosure (near future design)</li></ul>Print File Options: (both will fit together)Note: These will effect the top slotting for LED width, the interior walls will also be different but they will all connect together and not compromise the outside fit/look Narrow:<ul><li>(N) has a 12mm Top Interior Clearance - Available Now</li></ul>Wide:<ul><li>(W) has a 16mm Top Interior Clearance - Available Now (LED portions are coming ASAP)</li><li>(W) v3_2 had wider LED channels then the v3_1 to allow extra light into the channel</li></ul>&nbsp;Material used:PETG or higher is recommended if printing higher temp materialsStandard: 360g +/-Sliding: 425g +/-Backer: 210g +/-&nbsp;Settings:Recommended:<ul><li>0.2mm layer heights, </li><li>3 walls, </li><li>10-15% gyroid infill, </li><li>4 T/B layers, </li><li>75mm/s outside layer speed for better appearance</li></ul>&nbsp;<ul><li>Same as original but with an added LED channel, LED diffuser and LED top cap to add into the P1P frame.</li><li>Works with the X1C glass top and you'll just need to get the TPU pads from the original file!</li><li>Added back channel hole for the X1 series as well to make it compatible with both units</li></ul>After print:There are x6-7 0.4x0.8mm interior supports on the bottom to support the sliders during printing.<ul><li>Gently apply pressure from the inside back along the bottom of sliders.</li><li>You'll hear several pops as they are broken free</li><li>Use a small screwdriver or tweezers to apply gentle pressure pushing on the ends to help loosen the slides if they are being difficult</li><li>There is an internal locking mechanism in the bottom but there is top and bottom clearance to allow it to slide.</li><li>Slide the pieces together and install onto your machine!</li></ul>Other pieces are coming soon and will be updated in the respective folders once completed &nbsp;Associated Files:Top bracket for Glass or Enclosure: <ul><li><a href="https://www.printables.com/model/352439-bambu-p1p-x1-top-glass-adapter" rel="nofollow">https://www.printables.com/model/352439-bambu-p1p-x1-top-glass-adapter</a></li></ul>&nbsp;Revisions:Dec25: <ul><li>adjusted tolerances for fitting the keys together</li><li>added a thicker walls for top and filled in the sides for a complete glass top. </li><li>raised the exterior rib 2mm to give the glass more area to be covered on the side</li></ul>Dec 26:<ul><li>Added an Alpha phased version with sliding panels to the work file, tolerances have been tested to work and moving forward to production printing.</li><li>Added locking channels to keep the sliders in place and help with vibrations moving the sliders open or closed.</li><li>added more room for the top glass and other printed parts.</li><li>Created new pieces to attach as the originals were very stiff and often broe while trying to connect them</li><li>Added a back of P1P Top support to help hold it in place, it's a temporary piece until a full enclosure and side panels are created in the future</li></ul>Dec 28:<ul><li>Added.3mf files of the builds with suggested settings</li><li>Cleaned up the files for the Sliders and adjusted the Backer pieces to fit better</li><li>Changed the status of the files to Beta as they are printable and should be error free based on previous prints and digital revisions</li></ul>Jan 9:<ul><li>Uploaded the slider v3 files after PLA testing have been successful</li><li>removed the locking key on sliders as it was occasionally fusing or not giving the proper effect and will look into another solution in the future if requested</li><li>Wide version partially uploaded and will post the LED portions once they are completed</li></ul>Jan 16:<ul><li>Updated the (W) file for extra LED slot holes to better allow light into the Chamber</li></ul>Apr 10:<ul><li>Added a Step file for the Igloo enclosure and its smaller top glass sizing as a step file for easier adjustments to your overall cut and thickness</li></ul>June 18<ul><li>uploaded the W-Diffusers (sorry for the wait as its been a busy few months)</li></ul>Sept 27:<ul><li>revised a few overhangs and did a little cleanup</li><li>new files uploaded for anyone who wishes to work on it further</li></ul>