user_152431213

RomeoAlfa

This DJI FPV Goggles 2 Fat Strap Adapter is used to help accommodate aftermarket strap to fit the DJI Goggles 2.&nbsp;There are two files.  The one labeled “offset” can be used to shift the orientation of the strap up or down slightly.&nbsp;Print from TPU with 100% infill.

DJI FPV Goggles 2 Fat Strap Adapter 

航模RC

Jaatinen3D

➡️ <a target="_blank" href="https://than.gs/m/1055858?affiliateCode=Jaatinen3D" rel="nofollow noopener">Check out the new double barreled shotgun available on Thangs!</a> ⬅️➡️ <a target="_blank" href="https://than.gs/m/1066044?affiliateCode=Jaatinen3D" rel="nofollow noopener">Check out the new semi-automatic pistol available on Thangs!</a> ⬅️&nbsp;This little front loading single shot airsoft gun isn&#39;t very powerful, but it&#39;s fun! You only need a rubber band or two and superglue apart from the printed parts to build this!&nbsp;➡️ <a target="_blank" href="https://makerworld.com/en/models/401277#profileId-302766" rel="nofollow noopener">There is also a display stand for this gun!</a> ⬅️&nbsp;Printing tips:All the parts are oriented in the correct printing orientation.&nbsp;Use supports for Gun Frame Left and Gun Frame Right. All other are up to how your printer can handle small bridges.&nbsp;I recommend using a brim for Bullet Inner Clip.&nbsp;Assembly:See the assembly video here: <a target="_blank" href="https://youtu.be/CcxBWW-xZbo" rel="nofollow noopener">https://youtu.be/CcxBWW-xZbo</a>&nbsp;The bullets can fit up to 4 BBs, but I recommend using just one. You can try and see how a 4 BB bullet shoots. 😅If you don&#39;t have BBs, I&#39;ve included a printable bullet that works at least as well as a BB!

Tickler BB-13 — Fully 3D-printable airsoft gun

模型

V3 Precision

This is a spool winder for transferring filament from one spool to another. Inspired by the need to use certain filament spools for the Bambu Lab AMS. This build should speed up the process and give a nice tight winding. There is room for improvement, so feel free to give some feedback either on Printables or on the Youtube videos.This version is 100% 3D printed (not including the mounting screws). Future versions will use bearings and possibly a motor to drive the gears.The images show the assemblies mounted to a 2x6 for testing. The assemblies can be mounted to a similar board or to a base made from aluminum extrusions.&nbsp;Printing RecommendationsI used PLA while developing the spool winder. I would recommend using PETG, or Nylon CF, or other stronger, stiffer filament.The ‘worm’ gear can be tricky to print. In Bambu Lab Studio, I set the part upright and set support to tree (auto) and threshold angle at 10. Set a brim at 8mm.The gears are easy to print and require no support or post processing.The bases need some support and did well with tree (auto) and threshold angle of 30.I used 4 walls and 15% infill on most pieces. The thumbscrews I used 100% infill.&nbsp;AssemblyMost of the assembly is easy and self-explanatory.Note that the rear driven gear is reverse threaded.Specific instructions can be found in an upcoming Instructions Video …….There will also be a link to the video on the V3 Precision website.&nbsp;#best3dp2023<figure class="media"><div data-oembed-url="https://youtu.be/3llHdgb1ftQ?si=rh9tLXTMeOSzBDXe"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/3llHdgb1ftQ" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><figure class="media"><div data-oembed-url="https://youtu.be/ru2TtLahlmw?si=5opj3V5R-Ab6cPFX"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/ru2TtLahlmw" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

航模RC

模型

绕线器