user_1272505

Andreww

I designed this backplate to cover the exposed PCB on the  Elgato 4k60 Pro MK2 capture card, it uses the original 4 housing screws on the card, disregarding the hdmi bracket screws as not necessary. I added little square pieces as you can see in the CAD images, cut them off because they will touch parts of the PCB that isn&#39;t intended and will be bent wrong. They are purely there so the part can be oriented to print with supports, and the edges will be better supported and close the large bridge gaps.&nbsp;I included the Fusion360 screws for adaptations of the model to be made, feel free to customize it how you like!

Backplate - Elgato 4k60 Pro MK2

Nicco

After many iterations this is my model of a lens hood suitable for Nikon 18-55mm lens. It has a bayonet mount that can be secured for both active and resting position on the lens.If you have any advice or ideas to make it better, feel free to express yourself in the comments so I can upgrade the model on the way!

Lens Hood for Nikon 18-55mm

camera stuffs

arcanazen

Hi everyone this is my take on whisperit's d-pad mod. His version is good but I found it to be a little loose because of 1 single magnet. So my version uses 4 magnets.&nbsp;I bought a kit that comes with everything you need (magnetic d-pads and magnets). You can get it from here: <a target="_blank" href="https://www.amazon.com/dp/B08HRWSP7Z?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">https://www.amazon.com/dp/B08HRWSP7Z?psc=1&ref=ppx_yo2ov_dt_b_product_details</a>.&nbsp;Once you receive the kit, you have to remove the 4 magnets from the green d-pad and put them in your printed model. The magnets are secured with pressure, so make sure you press them all the way in.&nbsp;For installation you can use whisperit's guide: <a target="_blank" href="https://www.instructables.com/Legion-Go-D-Pad-Replacement/" rel="nofollow noopener">https://www.instructables.com/Legion-Go-D-Pad-Replacement/</a>.&nbsp;I used the AMS system for PLA filament for support interfaces. Also used 3 layers for raft.&nbsp;Finally inside Bambu Studio slicer I disabled the option that is for Remove small overhangs inside Supports tab.For print orientation I put the empty spaces for the magnets facing up.&nbsp;

Legion Go - Xbox One Elite Controller D-Pad

legion go

FV3Dprints

it is a back for the ASUS ROG Ally Extreme  to offer a bit of a different look  and possibly better cooling I'm a total newbie at modeling  so it might not look pretty  atm but I did say its a WIP (work in progress) ps.dont  print it like in  the photos  they are only there to show what the models looks like  i will replace those pictures later when  my prints are done eventually also  probably best to use abs or petg because the Ally gets pretty warm

ROG ALLY EXTREME backplate WIP

Ally

tropicgtiturbo

here is a simple mount i made for my moza r9 direct drive wheel. the bolt pattern works for all moza wheel bases. my sim rig stand was made for an angled logitech or thrustmaster wheel, so i made this adapter when i upgraded to the moza from the g29. at 50% infill its plenty strong. I&#39;ve been using mine for a full year as of 1/28/24 with zero issues doing drifting on assetto corsa for at least 3 hours a day and rally on dirt rally 2.0 a few hours a week.****updated design to work for moiza r5 wheels as well.*****

MOZA Direct drive racing wheel angled mount 

sim rig stuff 

LwFactory

A1 mini handle makes it easy to move your 3D printerRemove the cover at the top of the A1 mini Z-axis and replace it with this handle, and secure it with the original screws

A1 mini handle

a1 mini

3Dprint-K81

Check my Profile for more fun games:<a target="_blank" href="https://makerworld.com/en/models/159381#profileId-174976" rel="nofollow noopener">TicTacToe Evolution by 3Dprint-K81 - MakerWorld</a><a target="_blank" href="https://makerworld.com/en/models/137421#profileId-149543" rel="nofollow noopener">Basketball mini game by 3Dprint-K81 - MakerWorld</a>&nbsp;Do you want to have fun with friends? All you have to do is print out this impossible puzzle.&nbsp;Challenge your friends, it will be guaranteed fun.&nbsp;You can also find the stl file of the sphere, but I recommend that you take or buy a metal sphere (max diameter 8mm) for better playability.Here is the example link to buy it:<a target="_blank" href="https://www.amazon.it/gp/product/B0BHW7LL8C/ref=ox_sc_saved_image_3?smid=A2QKIRI1BQFJRO&psc=1" rel="nofollow noopener">PATIKIL 8mm Precisione Sfere, 25pz Cuscinetto Sfere 304 Inox Acciaio G100 : Amazon.it: Commercio, Industria e Scienza</a>&nbsp;You can choose to print it in two ways, easy or multicolor (see print profile)&nbsp;In addition, attached I release a pdf for assembly guide and any post-processing.&nbsp;&nbsp;Happy printing, I ask you to leave your feedback, thank you!!!!

Labyrinth mini game

toys/gadgets

InaniaEtVana

Whether you need a small adjustable holder for a pocket light or a new mount for your microphone, this model does it all, is adjustable (mechanical lock, not a friction lock) and clamps right onto any surface. Should be able to carry anything under a kilo or so depending on material and print settings (I have managed to load two connected light duty arms in PLA with 2.5kg, but it will flex). Want to design your own toolhead? Please do and share it! I have included a blank toolhead for you to use.&nbsp;The mount consists of the following parts:<ul><li>Table clamp</li><li>Arms<ul><li>Light duty (150mm) !only recommended for light loads!</li><li>Mid/Heavy duty (150mm)</li></ul></li><li>Tool heads<ul><li>Traditional adjustable clamp</li><li>Circular clamp</li><li>Microphone thread (5/8" 27 tpi)</li><li>Phone holder</li><li>Blank toolhead (make your own)</li></ul></li></ul>&nbsp;PRINTING AND ASSEMBLYThe model is easy to assemble and print. Just follow the instructions and recommended settings below. All .stl files are already correctly oriented.&nbsp;Clamp assemblyPrint settings:<ul><li>Outer walls: At least 4</li><li>Infill: At least 30% gyroid (100% rectilinear is recommended for arm swivel connector)</li><li>Brim recommended for main body</li><li>No supports</li></ul>To assemble the clamp first screw the large clamp screw into the large hole. <figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_xums1dzz2huc.jpg"></figure>Then push the screw cap onto the screw and screw in the small locking screw. <figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_976pf6bc363u.jpg"></figure>Glue the knob onto the arm connector using the hexagonal hole and protrusion.<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_93ev39lkrs6o.jpg"></figure> Place the arm connector into the clamp.<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_g89nb4e2741q.jpg"></figure>&nbsp;ArmsPrint settings:<ul><li>Outer walls: At least 4</li><li>Infill: At least 30% gyroid</li><li>Brim strongly recommended</li><li>No supports</li></ul>Glue the knobs onto the arms using the hexagonal hole and protrusion as a guide. Screw the arms connector on the clamp into the first arm part. <figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_pkphl32l1u6v.jpg"></figure>Keep connecting arms until you are satisfied. Tool heads connect the same way.<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_tai5jgtz9tw7.jpg"></figure>&nbsp;Tool head: Traditional clampAssembles and prints the same as the main clamp assembly.&nbsp;Tool head: Circular clampPrint settings:<ul><li>Outer walls: 4</li><li>No supports</li></ul>No assembly required. If you want a different diameter than the .stl files, you can make your own size by using the Fusion 360 file. Go to Modify → Change user parameters to change it to the diameter of the tool you want to clamp. &nbsp;Tool head: Microphone threadPrint settings:<ul><li>No specific requirements</li></ul>No assembly required.&nbsp;Tool head: Phone holderPrint settings:<ul><li>Supports ON</li></ul>To assemble this tool you will need an elastic band and 4 rods (6mm diameter) that are roughly the size of your phone. I used some M6 threading cut to size. You can 3d print 6mm diameter cylinders, but I prefer to use metal. Glue the rods into the holes of the top part of the phone holder (the shorter part). <figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_jgv6msmnb2kh.jpg"></figure>Glue the circular arm connector into the round hole of the bottom part of the phone holder. <figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_wzljr7ufmje5.jpg"></figure>Connect the two parts by inserting the rods into the bottom part of the phone holder. <figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_oudmiob20hfd.jpg"></figure>Put a rubber band around the hooks on the back.<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/47801/2023-09-28_ulzd9ql9zrlw.jpg"></figure>