Tiago P

AmethystAlice

Adjustable height holder for a 300x200mm honeycomb bed.This is intended to be used in a K40 laser cutter to provide an adjustable work bench&nbsp;Required Items<ul><li>300 x 200mm laser cutter honeycomb bed</li><li>5x 100mm M8 threaded rod</li><li>4x 608ZZ bearings</li><li>8x M8 nuts</li><li>8x M8 square nuts or half height locking nuts</li><li>2x M8 nylock locking nuts</li><li>8x M8 washers</li><li>4x GT2 drive pulleys with 8mm center</li><li>2x GT2 idler wheels with 3mm center</li><li>1x GT2 6mm timing belt 1250mm</li><li>2x M3 bolts 20mm</li><li>4x M3 washers</li><li>2x M3 nylock nuts</li><li>19mm x 19mm x 1.6mm aluminium square tubing<ul><li>2x 300mm length</li><li>2x 200mm length</li><li>2x 280mm length</li><li>2x 180mm length</li></ul></li></ul>Assembly Instructions&nbsp;Use the two 280 and 180mm tubes to form the upper frame along with the corner pieces with the longer arms and an m8 nut hole facing downwards, and the 300 and 200mm tubes to form the base with the four bottom corners that have a bearing hole facing upwards.&nbsp;The four threaded rods have a square locking nut at the bottom, a washer, a bearing, a GT2 gear, then an M8 nut, tighten the nuts at both ends and press fit the bearing into the bottom pieces, rod should turn freely and bearing should be a friction tight fit.&nbsp;Each of the top corners should have an M8 nut pressed into the recess on its underneath, and you can assemble the frame, just rotate the rods by hand for now.&nbsp;The tensioner arm, push an M3 nylock into the recess from underneath, then feed a idler wheel with one washer either side on an M3 20mm bolt into the hole and tighten against the nylock. After positioning the slicer carriage in the arm Insert a second M3 bolt through the bottom of the slider, with the same idler and washer configuration ontop and a nylock nut to secure it. both idler wheels should be able to spin freely. Slide two M8 square nuts into their recesses on the bottom of the slider, then feed an M8 rod through the arms outer hole, through the center of the slider and through those square nuts until it reaches the recess in the far wall of the tensioner arm. secure the outside end of the screw rod with another nylock nut. &nbsp;You can now feed the GT2 timing belt around the outside of the gears on the screw rods, and in a Z shape across the two tensioning idlers.You may use the same knob printed item to tighten the idler if it is too tight to do so by turning the nylock nut, but you will need to remove it in use as there is insufficient clearance to leave it fitted.&nbsp;Whilst the belt is loose adjust each of the corners so that they are the exact same height, then tighten the tensioner until the belt is taut. As a final step push the adjusting knob onto the nylock nut ontop of one of the screw threads, and you can cap the others with the small caps. &nbsp;Then simply drop your honeycomb bed into the frame where it should rest on the small ledges each corner piece has, adjust bed height by turning the nob, and all 4 corner rods should turn at the same rate, raising the bed evenly. If any corner slips, increase tension on the belt.&nbsp;

K40 Laser Cutter Adjustable Height Bed

laser stuff

FilliFuu

2 versions available, ears up & down.Easy to print with no brim or support needed.New flexi fidget design, clicks together or articulates - part of a growing collection available on my patreon.Happy Easter<figure class="media"><div data-oembed-url="https://youtu.be/fyvH5qXpKv0"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/fyvH5qXpKv0" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Cute Lucky Bunny Flexi Fidgets

Fidgets

K-Studio.ca

<h2>AMS Lite Hygro Clip</h2>Hygrometer Clip onto the top of the AMS Lite for A1 Mini system. Round design works seamless with the same AMS Lite design language. Battery door panel can easily access from behind or remove the hygrometer unit for servicing.<h2>Hardwares</h2>You can find Thermometer Hygrometer here on <a target="_blank" href="https://amzn.to/3TwcSQQ" rel="nofollow noopener">Amazon</a>.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/431380/2023-12-18_95e79d1826f19.jpg"></figure>&nbsp;<h2>Thank you</h2>If you wish to support me for future projects, please visit: <a target="_blank" href="https://www.buymeacoffee.com/kstudioca" rel="nofollow noopener">https://www.buymeacoffee.com/kstudioca</a>

AMS Lite Hygro Clip

A1 mini accessories

Embrace Making

<figure class="media"><div data-oembed-url="https://youtu.be/KOtIbI5YBWI"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/KOtIbI5YBWI" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;This is the Bambu Lamps LED Spool. Made from a Bambu Labs reusable spool, this lamp can be illuminated with a smart RGB LED strip and connected to your home automation system to be remotely controlled. It makes a very nice looking desk lamp or conversation piece within your office or shop. &nbsp;Please note that the Bambu Labs spools come in both translucent frosted plastic (preferred) or solid white. From what I can tell there is no guarantee that you will receive one or the other when ordering specific Bambu Labs materials. Either one will work but the frosted one allows light to also shine through the spool which looks nice. &nbsp;You will need the following items to complete this assembly. As an Amazon associate I may earn a small commission (at no extra cost to you): &nbsp;3D printed files: ► YOU ARE HERE&nbsp;LED Strip - the exact one I used in the video is no longer available but this is almost exact substitute: ► <a target="_blank" href="https://amzn.to/48HHbZ9" rel="nofollow noopener">https://amzn.to/48HHbZ9</a>&nbsp;Thread forming screws: ► <a target="_blank" href="https://amzn.to/3RRCKEr" rel="nofollow noopener">https://amzn.to/3RRCKEr</a>&nbsp;3M Double sided tape: ► <a target="_blank" href="https://amzn.to/3TVDGdH" rel="nofollow noopener">https://amzn.to/3TVDGdH</a>&nbsp;Bambu Labs Reusable Spool: ► <a target="_blank" href="https://us.store.bambulab.com/products/bambu-reusable-spool" rel="nofollow noopener">https://us.store.bambulab.com/products/bambu-reusable-spool</a>&nbsp;I would suggest printing all of the covers (front and rear), plus the LED filament diffuser in white material so light can easily pass through. The stand, screw and the color accent parts can be made in any color of your liking. I chose white and grey as they match the Bambu Labs color scheme nicely. &nbsp;PLA materials works perfectly fine and the typical 3 walls, 3 floors and ceiling layers is fine at 0.2mm layer height. Only the stand will need support material in a few locations. The LED diffuser file can be printed in normal mode - or optionally should be able to print in spiral vase mode. It is only one wall layer anyways so the result is almost identical but spiral vase mode will result in no Z seam.&nbsp; **************************************************************************** &nbsp;If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here: ► <a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y" rel="nofollow noopener">https://www.paypal.com/donate/?hosted_button_id=V2T6MEFUGP73Y</a>&nbsp;By supporting my channel you are encouraging me to continue with this time consuming endeavor. A lot of time goes into design work, building my projects, filming the videos, editing the videos, etc. Plus it all costs money! Your generosity goes a long way in helping me bring you better content as often as I can! Follow me on Instagram! &nbsp;► <a target="_blank" href="https://www.instagram.com/embracemaking/" rel="nofollow noopener">https://www.instagram.com/embracemaking/</a>&nbsp;

Bambu Lamps LED Spool

cool shit

GlennovitS 3D

<h3>Updates</h3>9. Nov 2023 - Added multiple new versions. Both with higher and lower angle (to fit more doors) AND all versions with a normal and a pointy version (where the tip is not rounded, to fit under doors with less space below)<h3>Description</h3>Want a minimalistic doorstop, that is easy to print and uses the material flexibility to lock the door in place - then look no further!<figure class="image image_resized image-style-align-right" style="width:357px;"><img src="https://media.printables.com/media/prints/623185/rich_content/aed7792d-4669-4877-908f-29c34302e360/thumbs/cover/800x600/jpeg/img_7500.webp"></figure><h3>Overview</h3>This doorstop comes in multiple sizes, and can be scaled to your liking. So give it a go, try it out, and if you want, print another one that is smaller/bigger, stronger or more flexible - to be the perfect fit for your door!<h3>Sizes</h3>The model comes in 24 versions now.It comes in 4 sizes: <ul><li>Small</li><li>Medium</li><li>Large</li><li>X-Large</li></ul>There are also 3 angles to fit different space below different doors:<ul><li>Low angle</li><li>Default</li><li>High angle</li></ul>And there are 2 styles of the tip<ul><li>Default (rounded at the tip)</li><li>Pointy (to fit under very tight spaces)</li></ul>All of the versions are 40 mm in width as standard, but can be scaled up and down in the slicer (just scale the Z direction)<figure class="image image_resized image-style-align-right" style="width:357px;"><img src="https://media.printables.com/media/prints/623185/rich_content/651b871f-7bc6-4796-b668-67954adf6f8b/thumbs/cover/800x489/png/skaermbillede-2023-10-22-kl-232657.webp"></figure><h3>Print instructions</h3><ul><li>Speed on first layer: 50% (To ensure good bed adhesion)</li><li>Infill: 0% (to make the model 'springy’)</li><li>Top/bottom layers: 0</li><li>Perimeters: 2-3 (try out different combinations - the ‘springyness’ is very depending on this parameter AND the material of your choice!)</li></ul>You can also to a stylised version with exposed infill if you like that look. Makes the model less flexible, but more stylised - your choice.<ul><li>Infill: 5-15%</li><li>Infill pattern: Honeycomb (or gyroid or whatever you like the best!)</li></ul>Happy printing!&nbsp;<h3>Want to show your support?</h3>You can see all my designs on Printables - and you can become an active supporter. I would really appreciate it!<a target="_blank" href="https://www.printables.com/@GlennovitS3D" rel="nofollow noopener">https://www.printables.com/@GlennovitS3D</a>

Springy Doorstop (flexible and in multiple sizes!)

usefull

3DPrintNovesia

A supportless version from my FIFA Worldcup Trophy Design

laser stuff

Fidgets

A1 mini accessories

cool shit

usefull

Luis