tw3nty3ight

Zurlingo-3D

<h2>Garden Dibber</h2>&nbsp;Ideal for planting seeds, bulbs and cuttings, this attractive garden dibber is an excellent tool for keen gardeners.&nbsp;Features:<ul><li>You can use this tool for making holes in which you can pop in plants raised in modules.</li><li>Draw shallow lines on your beds in the surface compost. These lines along a bed will guide your plantings and ensure they are in straight rows.</li><li>A further use is spacing. Use the dibber laid on its side to measure a perfect and consistent spacing for your plants, fruits or vegetables.</li><li>Markings every 2cm, up to 20cm</li><li>Super easy print</li><li>Strong design</li><li>Multiple ways to paint it (multiple plates included)</li><li>Mini version for A1 Mini</li><li>Large comfortable grip</li><li>Metric and Imperial versions</li></ul>&nbsp;A top tip when dibbing holes is to rotate the dibber as you withdraw it upwards. This makes for a clean hole with little compost sticking to the surface of the dibber.&nbsp;Thanks for looking!&nbsp;Please rate and review your printing experience :)

Garden Dibber 

planting

DesignCraft

This adapter system wraps the edges of a DURAMIC 1kg 199x66mm cardboard spool in order to:<ul><li>provide smooth rotation within a Bambu Lab AMS</li><li>prevent carboard debris from depositing within a Bambu Lab AMS</li></ul>Features:<ul><li>Reusable</li><li>DURAMIC nameplate for easy identification when reusing</li></ul>Instructions:<ul><li>Print this model twice for a single spool</li><li>Affix one spool ring adapter on each side of the DURAMIC spool</li><li>See attached photos</li></ul>Notes:<ul><li>Shown as printed with Bambu Lab PLA Basic at 0.2mm</li></ul>Considerations:<ul><li>Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.</li><li>Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.</li><li>AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">AMS Lid Riser</a> which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on <a target="_blank" href="https://makerworld.com/en/u/243407759" rel="nofollow noopener">my profile</a> or directly here: <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">https://makerworld.com/en/models/33133</a></li></ul>

DURAMIC Bambu Lab AMS Cardboard Spool Adapter Ring

AMS Adapter

inspectorNorse

This small click buckle for a Paracord bracelet consists of two parts: a male and a female part. Both parts are 3D-printed from PETG to ensure the delicate closure is robust.The click buckle offers easy handling and securely fastens the bracelet. To open, simply press the tab on the male part to release it from the slot.The design is based on Filip's design, which can be found here: <a target="_blank" href="https://www.printables.com/de/model/153417-tiny-buckle" rel="nofollow noopener">https://www.printables.com/de/model/153417-tiny-buckle</a>. However, I found the original design too unstable as the sidewalls of the female part would break every time. Therefore, I improved and reinforced the design using Tinkercad.&nbsp;Deutsch:Dieser kleine Klickverschluss für ein Paracord-Armband besteht aus zwei Teilen: einem männlichen und einem weiblichen Teil. Beide Teile sind aus PETG gedruckt damit der filgriane Verschluss robust ist.Der Klickverschluss bietet eine einfache Handhabung und sichert das Armband zuverlässig. Zum Öffnen wird einfach der Steg des männlichen Teils gedrückt, um ihn aus dem Schlitz zu lösen.Das Design basiert auf dem Design von Filip welches hier zu finden ist: <a target="_blank" href="https://www.printables.com/de/model/153417-tiny-buckle" rel="nofollow noopener">https://www.printables.com/de/model/153417-tiny-buckle</a>. Das ursprüngliche Design war mir allerdings zu instabil. Die Seitenwände der weiblichen Teils sind mir jedesmal zerbrochen. Deshalb habe ich das Design in Tinkercad verbessert und robuster gemacht.

Tiny Buckle for Paracord Bracelets

bracelet

3DPrintNovesia

The Original FIFA WorldCup Trophy and a modified version for the WorldCup 2022 in Qatar!&nbsp;

FIFA World Cup Trophy

trophy

左狗拳

模型外形参考：CSGO 骷髅匕首（Skeleton Knife）组装工具：无分件：无分件其他：一体打印，请视自己机器设置打印参数。原创模型，仅供个人打印，请勿商用。组装视频<figure class="media"><div data-oembed-url="https://www.bilibili.com/video/BV1yr4y1X7Ef/?spm_id_from=333.999.0.0&vd_source=ce261a6ae096f6019cad589ef253bc72"><div class="ck-media__wrapper" data-oembed-url="https://player.bilibili.com/player.html?bvid=BV1yr4y1X7Ef&autoplay=0&poster=1"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://player.bilibili.com/player.html?bvid=BV1yr4y1X7Ef&autoplay=0&poster=1" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>

planting

AMS Adapter

bracelet

trophy

knives

clock