tuckerjt07

planes01

<h3>Overview</h3>A-10 Kit Card upgraded to 3D fuselage format&nbsp;Check out the <a target="_blank" href="https://makerworld.com/en/models/199176" rel="nofollow noopener">SR-71</a>, <a target="_blank" href="https://makerworld.com/en/models/242106" rel="nofollow noopener">B-52</a>, <a target="_blank" href="https://makerworld.com/en/models/436445" rel="nofollow noopener">A-10</a>, <a target="_blank" href="https://makerworld.com/en/models/402126" rel="nofollow noopener">787</a>, and <a target="_blank" href="https://makerworld.com/en/models/405459" rel="nofollow noopener">Darkstar</a>!Check out the full airplane kit card collection → <a target="_blank" href="https://makerworld.com/@planes01/collections/991821" rel="nofollow noopener">linked here</a>!<h3>Profiles</h3><ul><li>Kit With Frame<ul><li>plane in a kit card format ideal for gifting to others</li></ul></li><li>Kit No Frame<ul><li>plane without a kit frame ideal for assembly right off the printer</li></ul></li></ul><h3>Filament</h3>As shown:<ul><li>eSun PLA+ Gray</li><li>Hatchbox PLA Gray</li><li>Bambu Lab PLA Black</li></ul><h3>Tips</h3><ul><li>Model requires close tolerances to ensure snug but not tight or loose fit<ul><li>Make sure the model cools to room temperature before assembly</li><li>Ensure filament is properly calibrated with no excessive over extrusion</li><li>If there is some over extrusion the parts may need to be lightly sanded at interfaces for fitment </li></ul></li><li>Ensure good bed adhesion<ul><li>Make sure printer is fully calibrated</li><li>Make sure print bed is clean &amp; dry (soapy water is my favorite for cleaning - simple &amp; works)</li><li>Make sure filament is dry (wet filament can generate non-continuous flow that can cause bed adhesion issues)</li><li>Cooling &amp; Temps - make sure they are correct for your printer, build plate, and filament</li><li>Smooth PEI plate is recommended</li></ul></li></ul><h3>Assembly</h3><ul><li>Remove all pieces from the kit</li><li>Debur as needed to smooth edges</li><li>Insert wing into forward fuselage slot</li><li>Insert horizontal tail into aft fuselage slot</li><li>Insert engine pylon into fuselage</li><li>Insert engine into engine pylon</li><li>Insert missiles into wing</li><li>Place airplane onto stand</li><li>Enjoy!</li></ul>&nbsp;Snap into place design<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000436445/design/2024-04-27_32e8c49417456.gif"></figure>&nbsp;&nbsp;&nbsp;

A10 Kit Card

kit cards

Robin S

<h4>On platforms like makerworld, printables and co. there are often phonecases to see but for most people it is the wrong phone!</h4>This is a phone case generator,where you can create your custom and individual phone case.&nbsp;You just have to follow the steps and measure out your phone. Then you have to put these measurements into the generator and you&#39;ll get a complete model including all offsets and risks!&nbsp;If you want to have the same look like in the cover picure remove upper and lower layers in your slicer settings and choose your favourite infill!&nbsp;&nbsp;<h3>Introduction</h3>You can create your own phonecase fitting to your phone.First you have to open the customizer web-tool from this model. Then you have to measure out your phone and put the in the web-tool described values in and then click on generate. After that you can download the 3d model.&nbsp;<h4>Special variables</h4>-&#34;cam hole distance&#34;: With these two variables you set the distance to the cam hole from the upper left corner. x means the distance horizantally and y vertically. (Same at “cam hole size”)&nbsp;&nbsp;-&#34;distance to upper button&#34;: You have to set this value to the distance from the upper edge of the phone to the first button on the right side of the phone. Buttons on the left side are coming soon! Offsets are included so don&#39;t change the values just put the exact measurements in.&nbsp;-&#34;text position&#34;: Here you can say where your text on the backplate of the phonecase starts. With xt and yt you can move the text on x aand y axis.&nbsp;&nbsp;<h4>Offset variables description</h4>&nbsp;<img class="image_resized" style="width: 51.49%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000478570/design/2024-05-31_97b47e74d476.jpg">Offset “o” is the main offset, which makes a little gap between phone and case.I recommend to set this offset to 0.2-0.6 mm.&nbsp;&nbsp;<img class="image_resized" style="width: 50.09%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000478570/design/2024-05-31_03af8a7bd6a57.jpg">The variable “n” sets how strong or how hard the case holds the phone in place.I mostly used 1-1.2 mm.&nbsp;&nbsp;<img class="image_resized" style="width: 49.98%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000478570/design/2024-05-31_9fe8713d1773b.jpg">With the variable “s” you set the height of the grips that holds the phonein the case. Here you can leave it at 1 mm.&nbsp;&nbsp;-Now I added a new feature where you can add a text on the backplate of the phonecase. Just put for example your name on it and move it to the right position with “text position” variables. You can also adjust the size of the text.&nbsp;-added feature: Buttons can be created on both sides. If the length of the buttons is set to 0 they will be removed.-added left speaker hole&nbsp;print tipp:-enable the feature in the slicer, print infill first. So your printer will print the overhangs better.&nbsp;&nbsp;&nbsp;If you successfully made your own phonecase, great job, please send me an email with your values if it’s not in the following excel sheet yet. Then send me the measurements, the phone name and a picture that you printed it to this email adress:<a href="mailto:3dprint_robin@web.de" rel="nofollow">3dprint_robin@web.de</a>So we can add those values to a big library where everyone has access to the sizes of their individuell phone.Otherwise you can upload a remix to this model to achieve the same.The link to the excel sheet:https://docs.google.com/file/d/1-4dP4UFD8Y4-3RfeF4kMAfZTcvU_xaJY/edit?usp=docslist_api&amp;filetype=msexcel&nbsp;

kit cards

phone scope