travis.hosmer50

JamesThePrinter

This container uses a quadruple slider-crank mechanism to lock its lid in place. There are many sizes available.Widths/Lengths available:<ul><li>100mm x 100mm</li><li>150mm x 150mm</li></ul>Heights available:<ul><li>30mm</li><li>50mm</li><li>100mm</li><li>150mm</li></ul>3 knob designs are also available.I have also included the F3D file for further customization. There are 2 parameters that can be adjusted to change the height and width (length and width are equal) of the container.Example of files needed (100mm x 100mm x 50mm container):<ul><li>Lid 100</li><li>Container 100-50</li><li>Outer Linkage 100 (Print 4)</li><li>Mid Linkage (Print 4)</li><li>Inner Linkage</li><li>Knob</li></ul>&nbsp;Print SettingsPrint all pieces in the orientation that they come. Be sure to print 4 mid and outer linkage pieces. Although PLA will work, PETG may work better for the mid linkages.&nbsp;Lid Assembly InstructionsWith the lid upside down, insert the inner and outer linkages. The orientation of the outer linkages matter. One face is flat, while the opposite has a slight taper. The flat side should be against the lid. The tapered side should face the container.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/1360890085/draft/2023-08-14_f0m8sis0xog4.png"></figure>&nbsp;With the inner linkage in a horizontal orientation and the outer linkages sticking out about 5mm past the outer edge of the lid, the mid linkages should snap into each piece. Some force is required. Be sure that you press them straight down - if they are tilted during pressing, they may snap.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/1360890085/draft/2023-08-14_9gdtgafgtfk2.png"></figure>&nbsp;The knob will need to be glued in place on top of the inner linkage. Place the knob onto the inner linkage and ensure that the linkage moves smoothly. Once happy with everything, use a small amount of glue to permanently connect the knob and inner linkage. If you use too much, it may run out onto the lid and lock everything in place.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/1360890085/draft/2023-08-14_mfozaxj7e0i9.png"></figure>&nbsp;&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Pink Container<ul><li>polymaker PolyTerra Candy PLA</li><li>Inland Pink Tough PLA</li></ul></li><li>Red Container<ul><li>polymaker PolyTerra Army Red PLA</li><li>polymaker PolyTerra Marble PLA</li></ul></li><li>Green Container<ul><li>Prusament Simply Green PLA</li><li>Prusament Opal Green PLA</li></ul></li><li>Orange/Yellow Container<ul><li>Inland Yellow Tough PLA</li><li>CC3D Flame Orange PLA+</li></ul></li></ul>

Mechanically Locking Container

Fun stuff to print 

JDJDJD

<h3>Meet the ProClip!</h3>The ProClip Filament Clip is a pleasure to use and easy to print.&nbsp;ProClip has a built-in handle that works in coordination with a clamping tunnel to manage and secure your filament.<h3>NEW! ProClip V2 features:</h3><ul><li>A extra durable clamp inside the tunnel.</li><li>Symmetrical input holes work for right handed and left handed users.</li><li>Handle flange provides good control and a comfortable grip.</li><li>A Low Profile option designed for tight storage containers.</li></ul>&nbsp;&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000030298/design/2023-09-30_0e45d041d5e2.gif"></figure>&nbsp;<h3>BENEFITS:</h3><ul><li>No Supports</li><li>No Overhangs</li><li>No Brims</li><li>Designed for FDM Printing</li><li>Free to Download!</li></ul><h3> </h3><h3>UPDATES:</h3><ul><li>10/06/23 ProClip V2 Released</li></ul>&nbsp;<h3>TIPS:</h3><ul><li>MUST be printed on side</li><li>Printer tolerances vary. If your ProClip is running tight just slide a piece of filament back and forth to break it in a little bit.</li><li>Glue stick can help condition the print bed for proper adhesion/release and is recommended.</li></ul>&nbsp;<h3>NOTES:</h3><ul><li>ProClip can be used commercially, but can’t be resold.</li></ul>&nbsp;<h3>TESTED PRINT DETAILS:</h3>ProClip has been built around the following conditions.<ul><li>Glue Stick: Yes (without is at your own risk)</li><li>Support: Disabled</li><li>Walls: 2</li><li>Brims: No</li><li>Nozzle: 0.4mm</li><li>Layer Height: 0.2mm</li><li>Infill: 15% Gyriod</li></ul>

Fun stuff to print

Bambu accessories