terryborei21

cyanidesugar

A wibbly wobbly timey wimey model for all the Whovians out here! &nbsp;This is another Hueforge Hybrid print, where the Tardis ‘pops out’ of the print for a little personality. This print combines Hueforge filament painting methods with traditional 3D printing to create a lovely pop art style print. &nbsp;Note: If you are using the 3MF for one click printing, all settings will have been applied to the model. I used 5 filaments for this on one AMS and swapped one spool out of the AMS when the colour was finished printing for the 5th colour. &nbsp;Note 2: This print also has steep overhangs with no supports. If you're not confident in your printer handling supports with my 3MF file settings, do not use the one-click printing function and import the 3MF file into your slicer and adjust the settings for the ‘Tardis_Export3.STL’ part of the assembly to suit your own supports/overhang settings. &nbsp;If you are not using the one-click 3MF, the print instructions and recommendations are as follows:<ol><li>This printed without supports, but I enabled slow down for overhangs. This print DOES require your printer / filament to be dialled in to be able to print the overhangs for the Tardis effectively. If you're not confident, I would enable supports. You would not be able to see it or remove it as the supports should only be applied to areas inside the Tardis. </li><li>I used a layer height modifier to modify the layer height specific to the Tardis (2.04mm - 33mm) to increase it to 0.16 to speed up the print.</li><li>I also modified the infill for the the Tardis and the ‘Generic Cube’ to only print at 10% with 4 walls and 4 top and bottom surfaces. </li><li>Since this print re-uses the Blue and the Black, if you are using only 1 AMS, I suggest swapping out Slot 3 (should be orange) for the white when you are swapping the colours out. </li><li>My recommendation is to have Black, Blue, Orange, Yellow in Slots 1,2,3, and 4 in the AMS, and then swap the orange for white when the orange is done printing. </li><li>If you want to use a different colour for the Tardis, then you can swap out the Blue accordingly</li></ol>Filament Instructions&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.2mm&nbsp;Filaments Used: - PLA Kingroon Black Transmission Distance: 0.4 - PLA+ Polymaker Starlight Neptune (Blue) Transmission Distance: 1.8 - PLA CC3D Orange Transmission Distance: 7.4 - PLA CC3D Lemon Yellow Transmission Distance: 8 - PLA Kingroon White Transmission Distance: 8&nbsp;Swap Instructions: - Start with Black - At layer #8 (0.76mm) swap to Starlight Neptune (Blue) - At layer #9 (0.84mm) swap to Orange - At layer #15 (1.32mm) swap to Lemon Yellow - At layer #17 (1.48mm) swap to White- At layer #24 (2.04mm) swap to Black- At layer #27 (2.52mm) swap to Starlight Neptune (for the Tardis!)&nbsp;The Tardis model can be found <a target="_blank" href="https://www.thingiverse.com/thing:367130" rel="nofollow noopener">here</a> by <a target="_blank" href="https://www.thingiverse.com/23Maple" rel="nofollow noopener">23Maple</a>.

Tardis in Space

misc

martin.taichl

This is 3D printable model of the Constitution Class NCC-1701 Enterprise from the Star Trek. It is a kit and does not require any glue. The different colored parts are separated for easier printing. The ship is a hybrid of TOS and SNW versions. Pieces of the necelles need to be separated into separate model in the slicer ;) For the assembly, please have a look at the following video. <figure class="media"><div data-oembed-url="https://youtu.be/HmZTOx1XaaA?si=SRYyh12Jd1WL4Nwe"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/HmZTOx1XaaA" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

misc

STAR TREK

a1/ams lite