I love that there are multiple options for the Trey insert very well thought out I chose this one. I felt it would fit Band-Aids for the kids better in the two smaller compartments print is great well-thought-out overall well done.

Super cute print, lots of depth really three-dimensional. Printed at 80% size felt it worked a little bit better for our tree compared to other ornaments definitely would not go any smaller and they’d still be great at 100%. These are gonna be great giveaways for visiting with family over Christmas

looks great in this two tone silk, question however is that a built-in support across the bottom or was that supposed to stay attached to the print? Does anyone know? It came off when removing it from the plate and it seems fine without it

this is a very good print, you can see there is some waste For the eyes, but in my opinion, well worth it for the output you get. All the joints work very well, but I made the mistake of turning on supports because when I went to print, I got a warning about needing support’s potentially and frankly it was late and I was printing this in a hurry, so it would be done by the morning for my daughter‘s birthday so in an abundance of caution, I turned them on and I think what happened is it actually created some tiny little supports in some of the joints that I had to very carefully and painstakingly clean out with an X-Acto knife. I could tell they were supports because they had some black and green on them and I know the Printer tries to use waste material for supports. Which turned out to be a good thing because I could easily identify the areas I needed to remove it. So do not use supports on this model even fit prompt you to do so.

Great print, just the right size Substantial enough to be sturdy and not break but not any bigger than it needs to be. Holds both rubber and braided cords fine, snug but not tight.

it’s big it’s heavy, but it’s substantial. It’s great for iPads. Nothing‘s going to tip over and slip out. I’ve printed a number of other ones that were much much smaller and you had to be so careful putting anything in them to keep it from tipping over. Well worth the filament, thumbs up.

I couldn’t have asked for more perfect design to run low-voltage cables through the house, in this case, ethernet and speaker, wires and coax. I was afraid they may not clip tight enough to hold a bundle of wires, but at least in the medium size the closure is very secure. The small version I wouldn’t wanna put a lot of weight on those clips, but they do what they need to. The various print profiles for this out there in different sizes made it very confusing and I accidentally printed the wrong sizes one time. Would love to have the author put everything in one file, a different size on every plate and allow us to print the plate that we need. Also would be great to see dimensions In the description, as opposed to small medium enlarge, it’s all relative. Printed in PLA, seem plenty strong no need to use pet G in my situation.

Great print quality, printing multiples saves you a lot of poop, very efficient use of materials. Control C and control V up to 10 of these and then select auto arrange. Print time somewhere around 11 hours. Only a few hours more than just a single print. As luck would have it, our elementary school mascot is a fox so these will be a great tchotchke to give out to the staff and teachers. UPDATE: These were a big hit and we decided to try some for his classmates but this time we did at 75%.

Cute little print, not much waste when you print the separate parts for the top, I noticed a third color for the top, which seemed unnecessary, it was the band right under the white part. As far as the catch that goes across the top, when you try to put that piece on, do not hold it by the ends and apply any force it will break very easily. I use a pair of needle nose, pliers to carefully work it down the shaft after putting a couple of dots of glue on the back of it. The first one I broke.

Great front, very functional fit perfectly. Looks like it’s part of the OEM set up. The supports actually came off when you lifted the main piece off, so there was no problem getting those out-of-the-way.

If you find The previous versions of this don’t even bother skip right to this one. Needs to make one of these without the silly face. The older versions you couldn’t retract the toothpaste back into the tube and it was just messy to use.

Worked perfectly, wasn’t sure how the filament was held by the clip, but for the record, the whole tapers slightly and creates friction within the tube, holding the filament, easy to pull in and out, but plenty of attention to hold it in place. Remember to use copy and paste for multiple prints on one plate

Easy And fast print, made this for my daughter‘s play kitchen, so she could learn The values of coins and make change from her new green bank.