swisstradeenterprise

Al3D

Train anywhere, even at the beach, with sand training dumbbells. These versatile tools adapt to any environment, allowing you to maintain and enhance your fitness routine no matter where you are.

Sand Dumbbells

fitness

Ross3D

I bought a set of solar-powered lights for my garage, and I quickly realized (out of my own ignorance) that I don't have a suitable place to attach the panel to as my house roof perimeters are surrounded by gutters.&nbsp;So I designed this extender arms to extend the mounting point of the solar panels so they get sufficient sunlight to charge up the batteries in my solar lights.&nbsp;The use of these extenders are not only for solar lights though. You can use it to extend anything you wish.&nbsp;There are two variants included - 200mm (about 7.8 inches) and 150mm (about 6 inches).&nbsp;For best outdoor resistance, printing in ASA is recommended due to it's UV resistance properties.&nbsp;The screw holes on the base and at the end are 6mm in diameter. &nbsp;Measurements of the 200mm is shown in pictures. For the 150mm variant, just subtract 50mm from the center portion of the arm (the base and end thickness remains the same).&nbsp;p/s: The photo shown with the solar panel attached is one of my earlier iteration of the design, which have been improved since.

Extender for mini Solar Panels

sollar project

francis.beland

This is a gutter elbow I did to replace mine that was lost for a long time. I made 2 versions. A smooth version and one with texture to mimic metal gutter. I strongly suggest printing it in PETG or ASA since it will be outside.

Gutter Elbow

house project

Ragnor

I am a huge fan of Fromsoft games and found this out on Thingiverse, but since there was no printable download file only and obj I converted to an stl via <a target="_blank" href="https://3d-convert.com/" rel="nofollow noopener">https://3d-convert.com/</a> and printed it.  Ended up turning out so nice I thought I would share so others didn&#39;t have to figure out how to convert it.&nbsp;You may want to increase supports in the eyes sockets and cheek bones as I have it limited but there might be some overhangs depending on filament.&nbsp;Enjoy!

Dark Souls 3 Wolnir Goblet

gothic

Print Design

Whether for an anniversary, a special occasion or simply to say “I love you”, this box of eternal roses is a gift that will touch the heart of the recipient. The box itself is stylish and versatile. It can decorate a nightstand, a desk or any special corner in your home.

Eternal Roses Box

Holiday

darwaishbndy

Introducing our functional barn birdhouse model, ideal for 3D printing on Cults 3D! This STL file is crafted for real-world use, providing a cozy and charming home for birds in your outdoor space. Designed to be mounted outside, this birdhouse is perfect for welcoming feathered friends into your garden or yard. Enjoy the beauty of nature as birds find refuge in this intricately designed and functional birdhouse, adding both aesthetic appeal and practicality to your outdoor environment.

CUTE BARN BIRDHOUSE

Qiola Iokasta

Minimalistic drone case for DJI mini 2. This case allows the drone to be safely stored away in any backpack with only taking up the absolute minimum necessary space.The drone slips in from the top and the fan blades automatically adjust to fit into the dedicates slots. The lid is securely held in place by a printed band.

DJI Mini 2 slim case

drone

oizopetr

End and corner of the kitchen worktop molding profile. For the Cucine brand from Bauhaus strip 24x16 mm.

The end and corner of the kitchen worktop profile.

floor_Project

Dish Engineering

Airless PingPong Ball 2.0. Listened to feedback from more than 1000 users that download the first iteration and updated the geometry design accordingly. Highlights of the update:<ul><li>Dissolved the pattern row that in some cases led to layer adhesion problems.</li><li>Extended the “Pole-like” geometry with bigger poles generating more spin.</li><li>3% weight reduction while slightly improving structural resistance.</li></ul>Still very important!<ul><li>Print with a Strong PLA like Overture&#39;s Super PLA +, or a rigid ABS/ASA for the best results. Flex PLA and TPU 98A will also work, but will be a trade off - They&#39;ll basically not break but will experience slight decrease in bounce.</li><li>If possible, print with slower speeds for the best results! (The one on the photos was printed in “Silent Mode” (50% of the speed) - it improves structural resistance as really thin like 3d printed structures bennefit greatly from steady printing (the less the vibrations while printing, the better)</li></ul>&nbsp;Check out the first iteration! - <a target="_blank" href="https://makerworld.com/en/models/248031#profileId-264262" rel="nofollow noopener">https://makerworld.com/en/models/248031#profileId-264262</a>&nbsp;Looking for a combo for you airless ball? Check out my recent professional spec&#39;ed airless ping pong racket! - https://makerworld.com/en/models/415669#profileId-317833&nbsp;

Airless Ping Pong Ball - V2.0 - A New Spin

Printerama

A simple little snowflake to decorate for christmas and winter

Snowflake light 

holidau

sduppleganger

So that's what happened to the toilet paper! &nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Filaments Used: PLA Black PLA Light Brown PLA+ Skin PLA White &nbsp;Swap Instructions: Start with Black At layer #7 (0.64mm) swap to Light Brown At layer #11 (0.96mm) swap to Skin At layer #18 (1.52mm) swap to White for the rest.

Squirrels Stealing Toilet Paper

背着画板打僵尸

Link to the other one：<a target="_blank" href="https://makerworld.com/zh/models/383709#profileId-283834" rel="nofollow noopener">https://makerworld.com/zh/models/383709#profileId-283834</a>Or click on my profile picture to find it on my homepage.

石狮子/FOO DOG(左/LEFT)

statue

Olivia

We designed these desk shelf legs generatively in Fusion 360 and produced them with SLS using the Sintratec S3 printer and robust PA12 nylon material. After printing and cleaning, we simply screwed the legs onto a wooden board and voilà: DIY Tabletop.

Table Legs for a Desk Shelf (Generative Design)

furniture

martenh

I made a <a target="_blank" href="https://makerworld.com/en/models/164075#profileId-180104" rel="nofollow noopener">previous version</a> but got feedback that larger connecting pieces were desired so I made this new version.&nbsp;If you have need for a specific size let me know and I&#39;ll upload the size you need.&nbsp;The first supplied print profile contain the sizes 12-20 mm x 47 mm  (diameter of hole and outer size): The are placed on individual plates for easier printing from mobile app. Check the name of the plate and print.&nbsp;The second profile contain the following sizes (hole and outer size):5/8&#34; x 1 1/4&#34; - Left3/4&#34; x 1 1/4&#34; - Right&nbsp;Keep the size you want and clone it as many as you need (2x number of pipes).&nbsp;Don&#39;t forget to leave a review, I&#39;d love to see your prints!&nbsp;Remember to check out <a target="_blank" href="https://makerworld.com/en/@martenh" rel="nofollow noopener">my other models</a>.&nbsp;<figure class="table"><table><tbody><tr><td><figure class="image image_resized" style="width:45.67%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000412090/design/2024-04-08_759ddcc7e3d4e.jpg"></figure></td><td><figure class="image image_resized" style="width:66.08%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000412090/design/2024-04-08_6bff6ff0ad821.jpg"></figure></td></tr><tr><td><figure class="image image_resized" style="width:78.97%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000412090/design/2024-04-08_8d473c0bbc7ce.jpg"></figure></td><td><figure class="image image_resized" style="width:46.44%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000412090/design/2024-04-08_f0b4a811f34a1.jpg"></figure></td></tr><tr><td> </td><td> </td></tr></tbody></table></figure>

Radiator Pipe Cover v2

Bathroom

Cy-Bea

Arrange your treasures with floral elegance.They can be printed seperatly and stacked or glued together.

Lotus ring & jewelry holder tray

jewlry

💡Idea Prints✔️

&nbsp;attention remember that it is a model with only one part &#34;vasemode&#34; so if printed in pla or petg open as much as possible the printer not to deform the walls is then and only not to waste material and its function to keep the poops does<h4>here are all the accessories for bambu also for maintenance→ <a target="_blank" href="https://makerworld.com/en/@Idea/collections/1009467" rel="nofollow noopener">COLLECTIONS</a></h4><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000410717/design/2024-04-13_d510d7402d5fa.jpg"><h4>★·.··.·★ 👋 Hello😁 ★·.··.·★</h4>Before reading the description I recommend in the future to look at the collections created by me for better service for high projects is to distinguish them better💚MAKERWORLD→ <a target="_blank" href="https://makerworld.com/en/@Idea/collections" rel="nofollow noopener">COLLECTIONS</a>&nbsp;&nbsp;purge filaments printed 2h and with very little material 65 gr&nbsp;

Filament Purge "VASE MODE" 

3d print

MKCAMC

I designed this version 2 of my Stackable Low-Profile Egg Dispenser in resopnse to feedback that I recieved from several people. This version is split into 2 parts which allows it to be printed on small format printers such as the A1 Mini and many others. I also increased the overall assembled length of the dispenser in order to allow for 6 eggs to be placed in it rather than 5. As in the original there is a slop to feed the eggs forward and a lip to keep them from falling out. Assembly is easy. Apply glue to either piece and then line up the fins and slots in between the 2 halves. You can print and stack as many of these as you need. I'm including a profile that has a brim and a profile that doesn't have a brim. I recommend using the brim, but it will take a little post processing to kae sure the brim material is cleared out so each section can stack. Enjoy!

Longer Stackable Egg Dispenser

kitchen

Tesial Design

For the Spring Floral Design Festival, I'm pleased to present the sunniest, smiliest pot in all of makerworld! 😁&nbsp;As you can see, it has been printed to accommodate an 8.5x8.5 cm pot, but you'll find the cut-out in the .3mf file in the form of a negative part, which will allow you to size the cut-out as you see fit!&nbsp;The sun is accompanied by its little clouds, which don't have to be printed. They adapt to the sun's shape, but never completely cover it ! ☀️☀️☀️&nbsp;&nbsp;

Sun and clouds flower pot

farm

Stag 3D

<h2>Chinese Dragon Lantern / 中国龙灯笼</h2>A modern traditional Chinese dragon lantern that&#39;s easy to print and assemble and will look great around the home. Great print for Chinese New Year, the year of the Dragon. &nbsp;Once printed and assembled simply place an LED tea light onto the base plate and fit the frame over the top.<ul><li>Slide both the diffuser and dragon style panels into the rails on each side of the frame.</li><li>The frame decorations are optional but can be blued onto the frame as pictured below should you choose to use them.</li><li>The lid can be pushed into place and will remain in place, however can be glued if preferred.</li><li>No supports are required for this model.</li><li>Plate glue recommended to ensure good adhesion.</li></ul><img src="https://makerworld.bblmw.com/makerworld/draft/834769/2024-01-10_27d6fc05174d9.png">&nbsp;现代传统中国灯笼，易于打印和组装，在家中看起来很棒。 打印和组装后，只需将 LED 茶灯放在底板上，然后将框架安装在顶部即可。&nbsp;<ul><li>将扩散器和龙式面板滑入框架两侧的导轨中</li><li>框架装饰是可选的，但如果您选择使用它们，可以在框架上涂上蓝色，如下图所示</li><li>盖子可以推入到位并保持在原位，但如果愿意，可以粘上</li><li>此模型不需要支撑</li><li>建议使用板胶，以确保良好的附着力</li></ul>&nbsp;

Chinese Dragon Lantern / 中国龙灯笼 

asian

StepanK

Made a 1/8 scale model of Gallardo LP560-4 wheel as wall decoration, so I can look at it even when I am sitting behind desk.

Lamborghini LP560-4 wheel

TheBear

I needed a place to hang my shirts for drying and was suddenly reminded of a door clothes hanger, I used to have some time ago. I can't remember exactly what it looked like, but I attempted to recreate it from memory. Hopefully some of you will find this useful as well :-)&nbsp;&nbsp;I've uploaded versions to fit 15-40 mm door widths, in 5 mm increments. Please let me know, if you need a specific width. I will gladly fix it for you!  My print was made with Eryone PLA+ - and I've tested it with hanging 2 kg (4.4 lbs) at the hook furthest from the door. Even with that weight at the very end, I still had to pull with quite a bit of force, before the hanger slipped over the door and fell. So, it will easily support a few wet shirts :-)  And due to the print orientation, it won't split at the layer lines. Enjoy and Happy Printing!

Door Clothes Hanger

organiser

2d printing enthusiast

Protector case for Intel CPUs in LGA1150, LGA1151, LGA1155 & LGA1156&nbsp;Triangle in corner for orientation.&nbsp;May need a little bit of support under the hinge, print profile has it.&nbsp;It should fit the listed sockets although I only have physically tested on a Pentium G3220.&nbsp;If you download & print the .obj scale it to 102.5%

Intel CPU Protector - LGA1150/1151/1155/1156

computer

fashion

SabreDesign

Modern Pen Holder stand to hold and display two pens in a stylish and modern way.&nbsp;Easy print, can hold pens up to 150mm wide. Also added a small indent on the back to store another item.&nbsp;If you want to support me you can join a patreon membership: https://www.patreon.com/SabreDesign&nbsp;Check out more of my designs below and on my profile: <img src="https://makerworld.bblmw.com/makerworld/draft/836512/2024-01-15_aa815a6e63302.png"> <img src="https://makerworld.bblmw.com/makerworld/draft/836512/2023-12-27_4dd127cfa82f5.png"> <img src="https://makerworld.bblmw.com/makerworld/draft/836512/2023-12-27_2951845da928b.png">

Pen Holder Stand

business

apex3D

I designed simple bit screwdriver that is inspired by the iconic design from Wera.<figure class="image image_resized" style="width:40%;"><img src="https://makerworld.bblmw.com/makerworld/draft/807199/2024-04-01_ba58dc10c0ee1.jpg"></figure><h4>FETATURES</h4><ul><li>Nice Wera design that is very ergonomic</li><li>Fit designed to be used without magnets</li><li>Still place for magnet if you wish…</li><li>Simple, reliable and fast print</li></ul>&nbsp;<h4>PRINTING</h4>If you plan to slice it yourself then just place it vertically, it has plenty of adhesion to print without issues and removal is easy.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/807199/2024-04-01_d1cdb9b351ae.gif"></figure>I would highly recommend OrcaSlicer, or BambuStudio with scarf feature. This design has no steep overhangs so it can utilize this feature which yields seems almost invisible and it looks super smooth.

Screwdriver for bits (Wera inspired)

tools

Tamazawa

Battery box for 16x AAA & AA batteries.Easy assembly, just have to push both parts together.&nbsp;AA box is scaled to 140% of original size.

AAA & AA battery - Rugged Box

tech

K-Studio.ca

Bathroom / Makeup Organizer mini cabinet includes many divider options from the print profiles. The dividers can be installed in all three shelf level.<figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-09_9eeee2d704509.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-09_c70e4220abc318.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-09_53c7709db3f648.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-09_5ad75ca62ce5d8.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-09_f516233e2b64d8.png"></figure></td></tr></tbody></table></figure><h4>Filaments</h4><ul><li>Bambu PLA Matte</li><li>Bambu PLA Basic</li><li>Bambu PETG Basic</li></ul><h4>Color Customization</h4>You can use the Bambu slicer paint tool by layer for the top hat shelf.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-07_8416caf9d3717.jpg"></figure><h4>Hardware for the drawer handles</h4>Option A<ul><li>CA Glue</li></ul>Option B<ul><li>2x M3x10mm screws</li></ul><h4>Instruction</h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-07_a17cd5ae73e7e.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-07_11dfaeaac8bcb.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-07_2144809887abd.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-07_e40fe7b391b3e.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/837624/2024-04-07_335b2bb9469e08.png"></figure>