sulleyneal

JustinHirsh

Simple Piccolo Trombone. Uses a Trumpet mouthpiece.Thank you @peteb for making an adaptor for the loose bell!

Working Piccolo Trombone

music

kaitlynrael04

Cute floating hide for aquarium or fish tank. I designed with my beta fish in mind. Easy to install, no hardwire required. PLA is fish safe, if using another filament, research if it is fish safe first.

Floating Aquarium Hide

fish

Bert Owen

Here is my favorite door stop. Must be printed in tpu or other flexible filament. Easy to print. I like the design because the screws are hidden and it looks great.&nbsp;If you want to use it to just protect your wall, print it without the door catch and with the longer bumper (Plate 2).&nbsp;If you want to use it as a door catch print it with the short bumper and the catch (Plate 1).&nbsp;Screw the bumper holder to the wall and then insert the bumper into the holder. It is a tight fit but it can be tapped in using a hammer.&nbsp;See my other design here: https://makerworld.com/en/models/109255#profileId-121864&nbsp;

Door Stop with Catch (TPU)

home

t.schafer

A model of the queen elizibeth tower that i have created in sketchup. Model should not require any supports but use your own judgement regarding brims dependant upon your setup.

BIG BEN (Queen Elizibeth Tower)

architecture

Justin Lauck

It's always a good idea to keep a few guitar picks in your wallet in case you need one. This design was inspired by my son constantly forgetting picks when he takes his guitar places.

Emergency Guitar Picks

Guitar

jarvizar

3d miniature of Magic Kingdom in Walt Disney World, Florida!&nbsp;Also includes the Contemporary Resort and Bay Lake Tower!&nbsp;&nbsp;&nbsp;Disneyland California Miniature: <a target="_blank" href="https://makerworld.com/en/models/252986#profileId-269372" rel="nofollow noopener">https://makerworld.com/en/models/252986#profileId-269372</a>&nbsp;Check out my collection of other miniatures: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/146964" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/146964</a>&nbsp;&nbsp;&nbsp;Model created in Blender using data imported with the <a target="_blank" href="https://github.com/vvoovv/blosm" rel="nofollow noopener">Blosm</a> addon.&nbsp;<h3>Slicing & Printing Details</h3>This model was designed to be printed with a 0.4mm nozzle (0.16mm layer heights) or a 0.2mm nozzle (0.08mm layer heights)&nbsp;I have uploaded two different print profiles for each nozzle size with the recommended settings pre-applied ready to slice and print!&nbsp;Each print profile includes two different models of Magic Kingdom, one with suspended monorail tracks and another with grounded tracks (no overhangs).&nbsp;<figure class="table" style="width:95.01%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image image_resized" style="width:100%;"><img src="https://makerworld.bblmw.com/makerworld/draft/700259/2024-02-06_94f5271985add.jpg"></figure>Suspended Monorail Tracks</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/700259/2024-03-01_5e235222ef045.png"></figure>Grounded Monorail Tracks</td></tr></tbody></table></figure>&nbsp;<ul><li>If printing with a 0.4mm nozzle, I highly recommend slicing the model using ‘Classic’ wall generation. ‘Arachne’ walls will usually omit some of the monorail pillars leading to poor bridging and stringing.<ul><li>*Note: if smaller details disappear after slicing with ‘Classic’ wall generation, try lowering the line/extrusion width of outer walls (external perimeters) closer to 0.4mm. Can also try enabling “Detect Thin Walls”!</li></ul></li></ul>&nbsp;<ul><li>If printing with a 0.2mm nozzle (or 0.4mm nozzle with the grounded tracks), I recommend slicing the model with ‘Arachne’ wall generation to include buildings and smaller details ‘Classic’ walls often fails to include.</li></ul>&nbsp;The included designer print profiles have the above settings pre-applied!&nbsp;Filaments used in photos: Sunlu Matte White (miniature), Bambu Matte Black (frame), Sunlu Sky Blue (water)&nbsp;<h3>Framing Details</h3>&nbsp;This model measures almost exactly 6.7in by 4.7in (170.5mm X 119.5mm) and should fit most 5x7 frames (assuming frame lip/overlap is around a quarter inch). Feel free to change the scale/size of the model(s) to meet your needs.&nbsp;Personally I use these cheap frames from Amazon: <a target="_blank" href="https://www.amazon.com/dp/B0C8HY7YSQ" rel="nofollow noopener">https://www.amazon.com/dp/B0C8HY7YSQ</a>And blue printer paper: <a target="_blank" href="https://www.amazon.com/Astrobrights-491618-Multipurpose-8-5-Inch-11-Inch/dp/B00006IDQT" rel="nofollow noopener">https://www.amazon.com/dp/B00006IDQT</a>&nbsp;I also included a fully printable frame (including a 1mm thick water plate) designed to fit all my miniature cities.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/700259/2023-12-27_7536c6348b762.webp"><figcaption>Gif of the Printable Frame</figcaption></figure>&nbsp;A frame is not required! This model looks great by itself and can be displayed almost anywhere.&nbsp;See my <a target="_blank" href="http://patreon.com/jarvizar" rel="nofollow noopener">Patreon</a> for a commercial license, early downloads, polls towards future models, and more!&nbsp;

Disney World Magic Kingdom 3D Miniature

A1 Prints

Jal Shah

Toddlers in my house have broken every door stop. On top of that with the old house, doors did not stay open. So far, I kept using simple door stops or any random items to stop the door from closing. But then I came across Spring Latch mechanism by 3D Printy and decided to design simple Door Catch with similar mechanism.<h3>Printing</h3><ul><li>Both parts print without any supports.</li><li>Print the spring with enough perimeter lines that the flexible arms are solid.</li><li>Pictured parts are printed with below settings and material.<ul><li>eSUN PLA+ Fire Engine Red</li><li>0.2mm Layer Height</li><li>3 Perimeters</li><li>5 Top and Bottom Layers</li></ul></li></ul><h3>Assembly</h3><ul><li>Both the spring and catch can be attached with two #6 or #8 wood screws to door and base board.</li></ul>

Door Catch

tools/house

valentines

awillkom

I found this really awesome fully printed monster truck toy on Printables. It has an integrated suspension sort of thing that works surprisingly well, and I can speak from experience that it's the most robust toddler toy I've ever made. They have survived a lot of abuse and kept on rolling.

Monster Truck Toy

toys

JAV-3D

<h3>English</h3>&nbsp;3D Printed UFO Table Lamp with Tractor Beam IlluminationIntroduction: Step into the realm of extraterrestrial aesthetics with the 3D-printed UFO Table Lamp. This guide details the assembly process and customization options to enhance your intergalactic lighting experience.Part 1: Components of the UFO LampPrint the four components:<ul><li>The bottom section providing stability.</li><li>The upper section holding the lighting elements.</li><li>The dome, completing the UFO design.</li><li>The Tractor Beam</li></ul>Part 2: Print Settings and Filament ChoiceUtilize white filament for a sleek appearance, or enhance the UFO effect with transparent filament. The print quality is optimized with a 0.4 mm nozzle.Part 3: Assembly Steps<ul><li>Combine the bottom and upper sections, ensuring a snug fit.</li><li>Optionally, use three printed pins for additional stability.</li><li>Attach the dome to complete the UFO shape.</li><li>Place the UFO ontop the Tractor Beam</li><li><img src="https://makerworld.bblmw.com/makerworld/draft/535851/2024-01-29_988fe0a13ce568.jpeg"><img src="https://makerworld.bblmw.com/makerworld/draft/535851/2024-01-29_4a1a5a55a013c8.jpeg"><img src="https://makerworld.bblmw.com/makerworld/draft/535851/2024-01-29_fb2376c5878d6.jpeg"><img src="https://makerworld.bblmw.com/makerworld/draft/535851/2024-01-29_1e4b483a335a68.jpeg"></li></ul>Part 4: Tractor Beam Lighting<ul><li>Position a wand-style LED light (linked below) inside the UFO.</li><li>The slightly tilted tractor beam allows you to place objects within the beam if desired.</li><li>Explore the impact of using transparent filament for a more captivating effect.</li></ul>Part 5: Cordless OperationUtilize a battery-powered wall LED for a cable-free lighting experience. The UFO lamp becomes fully mobile, providing flexibility in placement.Part 6: Share Your Illuminated UFOShare your unique variations, experiences, and lighting effects with the community. Encourage others to explore different color schemes and LED options.Summary: The 3D-printed UFO Table Lamp combines futuristic design with functional illumination. Whether casting a gentle glow or serving as an intriguing centerpiece, this lamp opens the door to creative lighting solutions. Enjoy the process of printing and illuminating your space with a touch of the extraterrestrial.Link to the recommended LED light: <a target="_blank" href="https://amzn.eu/d/9xn8wwf" rel="nofollow noopener">LED Wand Light on Amazon</a><h4>2nd Profile 7,6cmx4,5cm LED Wall light <a target="_blank" href="https://a.co/d/3IzJsVs" rel="nofollow noopener">Amazon</a> , <a target="_blank" href="https://www.aliexpress.us/item/3256805779521686.html" rel="nofollow noopener">AliExpress</a></h4>&nbsp;<h3>Deutsch</h3>&nbsp;3D-gedruckte UFO-Tischlampe mit TraktorstrahlbeleuchtungEinführung: Tauchen Sie ein in die Welt der außerirdischen Ästhetik mit der 3D-gedruckten UFO-Tischlampe. Dieser Leitfaden erläutert den Montageprozess und die Anpassungsoptionen, um Ihre intergalaktische Beleuchtung zu verbessern.Teil 1: Komponenten der UFO-LampeDrucken Sie die vier Komponenten:<ul><li>Der untere Abschnitt sorgt für Stabilität.</li><li>Der obere Abschnitt hält die Beleuchtungselemente.</li><li>Die Kuppel vervollständigt das UFO-Design.</li><li>Der Traktorstrahl sorgt für das Ambiente</li></ul>Teil 2: Druckeinstellungen und FilamentauswahlVerwenden Sie weißes Filament für ein elegantes Erscheinungsbild oder verbessern Sie den UFO-Effekt mit transparentem Filament. Die Druckqualität wird mit einer 0,4-mm-Düse optimiert.Teil 3: Montageschritte<ul><li>Verbinden Sie den unteren und den oberen Abschnitt, um einen festen Sitz zu gewährleisten.</li><li>Verwenden Sie optional drei gedruckte Stifte für zusätzliche Stabilität.</li><li>Befestigen Sie die Kuppel, um die UFO-Form zu vervollständigen.</li><li>Setzen sie das Ufo auf den Traktorstrahl</li></ul>Teil 4: Traktorstrahlbeleuchtung<ul><li>Positionieren Sie eine wandartige LED-Lampe (unten verlinkt) innerhalb des UFOs.</li><li>Der leicht geneigte Traktorstrahl ermöglicht es Ihnen, Objekte innerhalb des Strahls zu platzieren, wenn gewünscht.</li><li>Erkunden Sie die Auswirkungen der Verwendung von transparentem Filament für einen fesselnderen Effekt.</li></ul>Teil 5: Kabelloser BetriebNutzen Sie eine batteriebetriebene Wand-LED für ein kabelloses Beleuchtungserlebnis. Die UFO-Lampe wird vollständig mobil und bietet Flexibilität bei der Platzierung.Teil 6: Teilen Sie Ihr beleuchtetes UFOTeilen Sie Ihre einzigartigen Varianten, Erfahrungen und Beleuchtungseffekte mit der Gemeinschaft. Ermutigen Sie andere, verschiedene Farbschemata und LED-Optionen zu erkunden.Zusammenfassung: Die 3D-gedruckte UFO-Tischlampe vereint futuristisches Design mit funktionaler Beleuchtung. Ob sie einen sanften Glanz wirft oder als faszinierendes Highlight dient, diese Lampe öffnet die Tür zu kreativen Beleuchtungslösungen. Genießen Sie den Prozess des Druckens und Beleuchtens Ihres Raums mit einem Hauch von Außerirdischem.Link zur empfohlenen LED-Lampe: <a target="_blank" href="https://amzn.eu/d/gdKeGbq" rel="nofollow noopener">LED-Wandlicht auf Amazon</a>&nbsp;<figure class="image image_resized" style="width:93.89%;"><a href="https://www.amazon.de/dp/B0CGV5PBPT" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/535851/2024-02-01_f5a5a13e75d21.png"></a></figure>&nbsp;

UFO Table Lamp with Tractor Beam Illumination

space

warrell72

FeaturesMagnetic Sliding Lid: The deck box has a magnetic sliding lid that securely snaps into place, ensuring the safety of your sleeved deck. This feature provides easy access while keeping your cards protected.Versatile Dice Tray Insert: Accompanied by a dice tray insert, the deck box offers a convenient space for your dice, counters and other game accessories. The tray is removable, allowing you to create more room for additional cards when needed.Space-Efficient Lid Storage: The lid cleverly slides off and can be stored directly underneath the box. Secured again by magnets, this design minimizes the space it occupies in your playing area, ensuring a clutter-free gaming experience.Stackable Design: Magnets embedded in both the base and lid enable seamless stacking of multiple deck boxes. This innovative feature not only facilitates easy storage but also enhances maneuverability, providing a tidy and organized gaming space.Top Loader Display Slots: The deck box features strategically placed slots at the front and back for top loaders. Showcase your favorite cards, deck lists, or ink types, eliminating the mystery of what's inside each box. &nbsp;The magnets used are 15×5×3mm, the deck box will function without these but some features are lost.&nbsp;

Stackable Lorcana Deck Box

lorcana

Creativity Lab

An easy and useful print. Print in Single Color, assemble it and have fun!Thanks to the base, the crane won't tip over even with heavier keys.Assembly:<figure class="media"><div data-oembed-url="https://youtu.be/i8Ci-mMZrBU"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/i8Ci-mMZrBU" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;If you like the model, please consider dropping a Like to help us.

Crane Key Holder

office

2d printing enthusiast

Lightsaber Bookmark&nbsp;<ul><li>Prints flat</li><li>Half the lightsaber is 3d</li><li>Scale the STL to a size you like, example in images is 500%</li></ul>&nbsp;&nbsp;&nbsp;&nbsp;

Lightsaber Bookmark

bookmark

JamesThePrinter

This organizer is intended for your desk or 3D printer organizational needs. It features a mid-century feel with 6 separated storage areas. The included drawer should be used, but is not a requirement. The drawer handle requires 2 M3x12 bolts and is comprised of 3 pieces:<ul><li>Handle Support - Print 2x</li><li>Handle - Print 1x</li></ul>&nbsp;Print SettingsA brim may help with the handle pieces, but it is not necessary. No other special settings are needed.&nbsp;Drawer Assembly Instructions<ul><li>Insert both bolts through the holes in the drawer. </li><li>Slide the Handle Supports over the bolts. The flat end should be against the drawer. </li><li>Carefully screw the bolts into the handle. DO NOT OVERTIGTHEN. Because the handle is so small, it will crack if you overtighten the bolts. This is especially true if you use a silk filament. </li><li>Be sure to orient the curved end of the Handle Support correctly so that it pairs with the profile of the Handle.</li></ul><figure class="image image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/745895/2024-01-15_s740vq3lrdz5.png"></figure>&nbsp;&nbsp;<a href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Bambu Lab Matte Desert Tan PLA</li><li>Bambu Lab Matte Lemon Yellow PLA</li></ul>

Mid-Century Organizer

organization 

SavageLau

<h3>If you want commercial license, check out my bio and get it from Patreon.</h3>&nbsp;<h3>I am here to introduce you, retractable dragon wand! I made this design for Makerworld dragon contest (3/5). I think it will be a great addition Ornaments and toy for kids for new Dragon year. </h3>&nbsp;<h3>Best wishes to you all! 新年快乐.</h3>&nbsp;This wand takes me a while to design and tests. It takes around 2h33m to print and cost right around 50g filaments.The retractable part is not super rigid, it's by design, I did not put a lot of parameter in there, consider this will most gives to kids to play. So rather it break than hurt somebody.&nbsp;<h2>Update:</h2><h3>v1.5 (1/13/24) - Fix internal parts geometeric issue. (tested) It only applys on P & X Series profile.</h3>Printing profile for P & X Series have found geometric issues on inner parts. Which only occurs when selecting P&X series printers, A1 and A1mini profile doesn't have this issue. Internal parts have been redo. Profile for a1 mini, A1 have remained as v1.4 since it is working correctly.&nbsp;&nbsp;<h2>Detail display:</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/413415/2024-01-11_161fe41bfd6c.gif"></figure>&nbsp;&nbsp;<h3>My other wand design: </h3>Loong Wand:<a target="_blank" href="https://makerworld.com/en/models/143028#profileId-155486" rel="nofollow noopener">https://makerworld.com/en/models/143028#profileId-155486</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/413415/2024-01-16_55943d4f3e579.jpg"></figure>&nbsp;Harry Potter Wand: <a target="_blank" href="https://makerworld.com/en/models/68778#profileId-72937" rel="nofollow noopener">https://makerworld.com/en/models/68778#profileId-72937</a> <figure class="image image_resized" style="width:69.8%;"><img src="https://makerworld.bblmw.com/makerworld/draft/413415/2024-01-11_db6b2ce5b060b.jpg"></figure>&nbsp;<h2>Instruction:</h2>I put very large size of brim on all my printing profile, with 0mm gap to ensure the printing success rate. Since this model is a bit challenge to print.You will required to do some post work of removing brim off. It should be very simple. I have increased gap on first layer from design, so it is tight tolerance, but not super tight.&nbsp;&nbsp;<h2>Materials:</h2>If you are printing with some high shrinkage rate filaments, like some of the silk filament. Due to the sinkage rate different. Your part might slide out or break very easily. So, use some good filaments.&nbsp;<h2>Design:</h2>Let's talk about a little bit of design. The retractable mechanism is very simple, the inner piece is interlocking with outter pieces.<figure class="image image_resized" style="width:24.07%;"><img src="https://makerworld.bblmw.com/makerworld/draft/413415/2024-01-11_651c54592313e.png"></figure>Style is more challenging<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/413415/2024-01-11_37b064643dfb6.png"></figure>Adding more details.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/413415/2024-01-11_d16c3620c7aab.png"></figure><h2>Printing suggestions:</h2>This is a tall object with very small contact area on first layer. It is challenge to print. It will print without brims, but it fail very easily that way. If you are slicing the model yourself, make sure you add brims, and set brim gap to 0mm. Also increase the first layer thickness.Or, just use those profile that I put there. It all have been tested and confirm works.&nbsp;&nbsp;&nbsp;

Dragon Wand (Retractable) v1.5

dragon

Drake

!!!Be sure to change the size of your print nozzle to 0.4mm if printing w/ default nozzle!!!&nbsp;Printed with 0.6mm nozzle and Bambu PLA-CF Burgundy / PLA Sparkle Purple. Included 0.4mm nozzle file and 0.6mm nozzle file along with step file. Customizable.

Men's Size 8 Dome Ring 2 Color (Includes step file for resize)

rings 

Conchulio

Eine Schöne und Praktische art seine Zahnbürste mit auf Reisen zu nehmen.Es Passen Bürsten von Oral B und Zahnheld (Geko) in die Box.die Ausbuchtung für die Bürste beträgt 32x205 und für den Bürstenkopf 17x85

Electric toothbrush travelling case Geko/Zahnheld/Oral B

toothbrush

Ciuf_Ciuf

<h2>General description</h2>After the great success of the drainage project, I am proposing a simpler and more intuitive version, especially for new users and beginners who are approaching the world of multicolor.&nbsp;<a target="_blank" href="https://makerworld.com/en/models/54909#profileId-56456" rel="nofollow noopener">https://makerworld.com/en/models/54909#profileId-56456</a>&nbsp;The basic purpose is always to minimize purging material as much as possible to save on color changes and drastically reduce the amount of discarded materialI have decided to update the model and make it more user-friendlyThe basic idea was to make it a standard Bambulab Calibration, similar to the K calibrationSo, lines with numbers to instantly identify which value is the most accurate to assign to the purging of the respective materialBeing a test, it must be as economical as possible, so a test strip requires only 2 grams&nbsp;I'm leaving you the video of a guy who explains in detail how to use this type of calibrationI thank him for considering my project for the creation of a video on YouTube, and I'm pleased that I've shared his video<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=FP3CwBX6A4I"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/FP3CwBX6A4I" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><h3> </h3><h3>Pre-print Procedure</h3>*Edit 03-01-2024*&nbsp;From one of the various print profiles you download, you'll need to set the color combination you desire<figure class="image image_resized" style="width:47.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2024-01-03_36c2f25737bbb.png"></figure>In my case, I'm calibrating these purge combinations, and the model will result like this<figure class="image image_resized" style="width:36.6%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2024-01-03_e5017ae8f46d08.png"></figure>If you want to change the color combination, simply use a different type of filament<figure class="image image_resized" style="width:37.2%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2024-01-03_a174ecda4566d.png"></figure>and the print profile will adapt to the combination you have set, as in this case<figure class="image image_resized" style="width:37.37%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2024-01-03_f1abfb2fe5f0a8.png"></figure>The model will update in real-time, allowing you to see immediately which color you are changingI've implemented additional print profiles to significantly streamline the procedure.While the process can be fast for those with a single AMS, it might be quite lengthy for those with multiple using the previous print profiles.With these new print profiles, there is also increased compatibility for the A1 Mini model.&nbsp;The idea of implementing the print profiles in this new way was suggested by Michael when he uploaded his print profile for the V1 model. I'll leave you the link to his Makerword channel (<a target="_blank" href="https://makerworld.com/en/u/2954682459" rel="nofollow noopener">https://makerworld.com/en/u/2954682459</a>)&nbsp;As on the previous model, it is necessary to reduce the purging material to allow us to calculate the material quantity adequately.The only significant difference is that this time we set all purging quantities to 0On the dual-object print profile, you can also do it manually.However, on the other print profiles, if you want to expedite the process, you can set the multiplier to 0, instantly reducing the purge to 0<figure class="image image_resized" style="width:35.51%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_f161c5ce7c0868.png"></figure>Now you can start the printing process&nbsp;Note: Do not touch any other parameters I've set, or the colors won't be printed in the correct order<h3>Calibration reading</h3>After completing the print, for calibrating the K factor, we need to read and determine the most accurate value to set as the purging quantityWhat you will find in front of you will be this<figure class="image image_resized" style="width:46.93%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_02e09355d1abf8.jpg"></figure>As you can see inside the two green rectangles, that is the exact moment when the material is purged, and the next color takes over.<figure class="image image_resized" style="width:46.78%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_617da72c674e78.jpg"></figure>At this point, all that's left is to identify the correct value and set the purging quantity for that specific color changeFor these tests, it's highlighted that 150mm^3 of material is required to perform the color change<figure class="image image_resized" style="width:46.33%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_e9817c7179a71.jpg"></figure>In this specific case, the quantity is identical for both color changes, but for other combinations, it may varyAs you can see, the difference between the default values of Bambustudio and the ones just found is significantly lower.This allows us to reduce material waste and significantly cut down on print times, decreasing the time the printer takes to change the filament<figure class="image image_resized" style="width:35.41%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_a67e103190684.png"><figcaption>BEFORE</figcaption></figure><figure class="image image_resized" style="width:35.53%;"><img src="https://makerworld.bblmw.com/makerworld/draft/624812/2023-12-29_ab83cab72d7d18.png"><figcaption>AFTER</figcaption></figure>&nbsp;

AMS Purge Calibration V2

calibration

Alex.M

My daughter wanted to wear <a target="_blank" href="https://makerworld.com/en/u/2571622071" rel="nofollow noopener">DorAndy</a>&#39;s the flexetki toy as a bracelet, so I combined it with <a target="_blank" href="https://www.printables.com/@Mistertech" rel="nofollow noopener">Mistertech</a>&#39;s Strap buckle (the only buckle I could find that prints flat) into a sort of bracelet.&nbsp;There is a new/different model (printed on the side this time) here: <a target="_blank" href="https://makerworld.com/en/models/235372" rel="nofollow noopener">https://makerworld.com/en/models/235372</a>&nbsp;

Flexi bracelet (fun bracelet for kids)

bracelet

FilliFuu

Double jointed articulated dragon, with folding fins, I designed in blender and added a new style fin joint in addition to the common link join for the body that is typically found in other articulated models. Also miniature versions to fit the A1 mini.&nbsp;Also uploaded multiple colour print profiles if you wish to print with your ams and don't mind the extra print time.&nbsp;Recommend gyroid and brim unless you have perfect bed adhesion - all print in place&nbsp;Tested in multiple colours and sizes without any problem - the mini size uploaded is the smallest i have tested and would recommend - the largest will fit on a 220x bed so upscale if you wish.&nbsp;Have fun.

Double Articulated Scale Dragon

dragons

sthompson984

NHL light box for the New York Rangers

New York Rangers Light Box

light boxes 

dohara1985

Meat Temp guide. Available in both Fahrenheit and Celsius. Temp guides are available with magnet hole, hoop to hang or both.&nbsp;&nbsp;Colors can be done with color swap or AMS. Profiles I have uplaoded are color change pause.&nbsp;&nbsp;Magnets are 8 X 3 mm. I picked up a 100 pack on Amazon for $8 usd.&nbsp;Magnet holes are super tight, so no need for glue, but they are difficult to push in. I Put the stack on the hole and then hit the top of the stack with a mallet. Be careful not to break off the fish. (Ask me how I know).&nbsp;If using magnet version, use supports for the hole.&nbsp;&nbsp;<h3>Commercial license</h3>As of 2/25/24 my designs are no longer allowed to be sold commercially.Do you want to sell prints of this model or any of my models? You can purchase commercial licensing at <a target="_blank" href="http://www.patreon.com/ErraticallyEccentricCreations" rel="nofollow noopener">Patreon</a> or Buy Me A <a target="_blank" href="https://www.buymeacoffee.com/dohara1985o" rel="nofollow noopener">Coffee</a>. Earring Commercial Liscence is just $3 a month. A full commercial license for all of my designs is just $7 a month.

Meat Temp Guide F or C

kitchen

dekopuma

An easy to print pair of 2024 glasses to show your New Year's Eve spirit! &nbsp;These glasses are printed in three pieces: The front glasses part and two earpieces. The earpieces can be inserted in any of the hexagon holes, letting you easily adjust the width to best fit your head. I like mine with two open hexes on the outside of each earpiece. Happy New Year!