Simon无限可能

Lp3d

I have received several requests for a commercially licensed model.This model may be used commercially, in return I have included my Instagram name.&nbsp;I think this should be a fair deal for both sides ;-)

TicTacToe - KeyChain - Commercial Licence

已获授权商用

我的二创-非商用

我的二创-可商用

我的原创-可商用

我的原创-非商用

无明业火_BLAZERS

兔司机斜坡玩具(ramp walker toy)组装说明 斜坡兔司机玩具演示和组装视频教程请浏览网页：<figure class="media"><oembed url="https://www.bilibili.com/video/BV1Hz42117d4/?spm_id_from=333.1007.top_right_bar_window_history.content.click&amp;vd_source=98342c314efc5f602442dd4deeae80c1"></oembed></figure>1.所需五金件：不锈钢销钉Φ2x16一支； 2.防滑贴纸：厚度0.5mm，宽度20mm，某宝有售； 3.组装要点： A组装后必须保证腿部转动灵活无卡涩； B两脚底板保证平行，否则玩具可能无法保证直线行走； C斜坡玩具是需要玩具本身和坡度配合完成运动，玩家需要自行调整坡度角度，达到最佳效果； D斜坡玩具防滑很重要，为达到最佳效果，请尽量使用防滑贴纸和粗糙的斜坡； 4版权声明：全部文件免费开放，二创或商用请注明作品出处。

斜坡自走玩具（ramp walker）兔司机

可署名商用

ShIfTy492

I never really liked the Ball Makers for Groundbait that are available on the market in terms of stability. That's why here are my own two versions in 40mm & 60mm diameter.Feel free to modify or change these further.Have fun printing and fishing.

Ground Bait Ball Maker

Fishing

NGYX

还在烦恼A1/A1mini打印的时候缺料和挤出机丢步吗来试试这个挤出机电机散热支架吧只需要一个5v的4010风扇 四个m3螺母和四个m3x12/m3x10（取决于使用的风扇）的螺丝模型请使用petg打印 接线可以参考最后一张图想要风扇自动启停可以参考视频<a target="_blank" href="https://www.bilibili.com/video/BV19D421G7RT" rel="nofollow noopener">https://www.bilibili.com/video/BV19D421G7RT</a>Are you still bothered by issues of filament run-out and extruder skipping during your A1/A1mini printing sessions?Why not give this extruder motor cooling bracket a shot?All it takes is a single 5V 4010 fan, along with four M3 nuts and matching screws (either M3x12 or M3x10, depending on the specific fan you&#39;re using).For the bracket, it&#39;s recommended to print it using PETG material. As for the wiring, kindly refer to the illustration provided in the last image.Should you wish to have the fan operate automatically turning on and off, feel free to take cues from the video tutorial available at:<a target="_blank" href="https://www.bilibili.com/video/BV19D421G7RT" rel="nofollow noopener">https://www.bilibili.com/video/BV19D421G7RT</a>&nbsp;2024/5/21-更改了螺母朝向 打印不会出现破壁了 The orientation of the nuts has been altered to prevent wall breakage during printing.-缩短了支架和工具头的距离 让支架安装好没这么晃 The distance between the bracket and the hotend has been reduced, ensuring less wobbling once the bracket is installed.&nbsp;如果你喜欢的话可以点个赞支持一下，谢谢！If you like it, feel free to give a thumbs up for support. Thanks!