stevesimonsen

Rockettree

Wall mount hammer holder.&nbsp;Requires 2 8g wood screws to attach to the wall

Hammer holder

Pegboard Stuff

jarvizar

Large Square version of my smaller <a target="_blank" href="https://makerworld.com/en/models/95824#profileId-102145" rel="nofollow noopener">Midtown Manhattan miniature</a>!&nbsp;Modeled in Blender using the <a target="_blank" href="https://github.com/vvoovv/blosm" rel="nofollow noopener">Blosm</a> add-on.&nbsp;Notable included landmarks:<ul><li>Empire State Building</li><li>Times Square</li><li>Madison Square Garden</li><li>Chrysler Building</li><li>Grand Central Station</li><li>Rockefeller Center</li><li>Bryant Park + New York Public Library</li><li>Hudson Yards + Vessel</li><li>And much more</li></ul>Check out my collection of other miniature cities: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/146964" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/146964</a>&nbsp;Larger version of Manhattan including the East River & Hudson River: <a target="_blank" href="https://makerworld.com/en/models/111838#profileId-119762" rel="nofollow noopener">https://makerworld.com/en/models/111838#profileId-119762</a>&nbsp;This model was designed to be printed with a 0.4mm nozzle and 0.16mm layer heights. Try using a 0.2mm nozzle (0.08mm layer heights) or scaling up for even finer detail!&nbsp;Note: If roads or other small details disappear after slicing, try or lowering the extrusion/line width of external perimeters (outer walls) closer to 0.4mm OR use Arachne walls.&nbsp;Framing Details&nbsp;This model measures almost exactly 8.5x8.5in (217.2mm X 217.2mm) and should fit most 9x9 frames (assuming frame lip/overlap is around a half-inch). Feel free to change the scale/size of the model(s) to meet your needs, but if the model is shrunk too much smaller features such as roads and vegetation might too small for the slicer to recognize. I plan on uploading an even larger version in the future without these details for more freedom with scaling and sizing.&nbsp;Personally I used this cheap frame from Amazon: <a target="_blank" href="https://www.amazon.com/dp/B0C9GMB1X8" rel="nofollow noopener">https://www.amazon.com/dp/B0C9GMB1X8</a>&nbsp;A frame is not required! This model looks great by itself and can be displayed almost anywhere.&nbsp;If you are interested in selling my models, see my <a target="_blank" href="https://www.patreon.com/Jarvizar" rel="nofollow noopener">Patreon</a> page for a commercial license.&nbsp;

New York City Manhattan Square 3D Miniature

Planning to print

SprocketStudios

Update January 25, 2024: A new version of this model has been released! It prints much cleaner at the bottom, and has the same threading. <a target="_blank" href="https://makerworld.com/en/models/156286" rel="nofollow noopener">Check it out here</a>. &nbsp;This is a large threaded egg. It was designed to be large enough to hold one of <a target="_blank" href="https://www.printables.com/model/525789-articulated-dragon" rel="nofollow noopener">McGybeer's articulated dragons</a> (printed at the default size). Looks particularly good in multicolor coextruded filaments.&nbsp;It will print OK without supports, but the bottom points of some of the scales get a bit messy.&nbsp;Update January 5, 2024: There is a new “revised” version which aims to address some of the issues with the messy early layers. It's not perfect by any means, but it has a wider base which is less prone to issues. There is also improved alignment of the lower scales.&nbsp;If you would like to print this model for commercial use you must purchase a license here: https://thangs.com/designer/Sprocket%20Studios

Pegboard Stuff

Planning to print

Looks Interesting