steuberli90

Havoc_Eins

Made a simple display stand for the HC Diana foam dart blaster using negative parts in the slicer. Because of that, there was some warning stating “conflicting gcode detected” but it's as intended. Would greatly appreciate it if anyone could make a proper STL/3MF and print the profile from the raw file.&nbsp;Update 8/12/23 : Fixed the file by using the slicer's “assemble” function, warning has been removed. Should print with no issue but let me know in the comments/review!

Nerf HC Diana Display Stand

Nerf

elikoll

This is a must have for all L E G O fans!Let me see your finished prints. 🤩&nbsp;

L E G O Brick Head Croc Charm

Fashion

printingbuddy

This is my interpretation of mounting the X-Wing on the wall.

Poe Damerons X-Wing Starfighter Wallmount (75273

Lego

ItsVRK

Note: There is now a V2 of this model <a target="_blank" href="https://makerworld.com/en/models/458322" rel="nofollow noopener">https://makerworld.com/en/models/458322</a> I got so tired of poop jumping out while the nozzle was being cleaned so I created this Poop retainer and added a section. of A1 Nozzle wiper to the tail end of the process.. no more wisps!<figure class="media"><div data-oembed-url="https://youtu.be/et-Bg7UNox0"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/et-Bg7UNox0" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>This screws into place using the existing screws either side of the purge chute. Cut a 3x3 square of A1 Filament wiper (I suggest cutting the rounded end row off first so you have a nicely square part, you&#39;ll get 12 pieces from the linked part) <a target="_blank" href="https://store.bambulab.com/collections/spare-parts-for-a1-series/products/heatbed-nozzle-wiper-a1" rel="nofollow noopener">https://store.bambulab.com/collections/spare-parts-for-a1-series/products/heatbed-nozzle-wiper-a1</a> &nbsp;I printed the main part with PETG using PLA as support for a super clean interface, see the third image for how to remove the support from the place where the A1 Filament wiper. Check out my other X1C/P1S mods:<ul><li><a target="_blank" href="https://makerworld.com/en/models/427348" rel="nofollow noopener">Clip in place AMS Buffer Power Release</a></li><li><a target="_blank" href="https://makerworld.com/en/models/426096" rel="nofollow noopener">Clip in place AMS Buffer PTFE Release</a></li><li><a target="_blank" href="https://makerworld.com/en/models/444558" rel="nofollow noopener">Clip in place AMS HUB PTFE Quick Release</a></li></ul>

X1C Poop Retainer and A1 Nozzle Wiper

Printer Upgrades

3Deekes

Another “Art Deco” Hueforge , this one is a Minion :). I think a lot of people will have someone in their live that is into The Minions , this is a great gift to print for them :)&nbsp;The dimensions are 180x180 mm so it fits nicely in a square frame (as seen on the second picture). &nbsp;I also made a frame you can print to use for this and my other Hueforge models :&nbsp;https://makerworld.com/en/models/194571&nbsp;The colours I used are all Elegoo Filament. Black → Blue → Yellow → White&nbsp;The plate is now 180x180 but you could resize to bigger or smaller, just make sure you do not change the height (Z) so uncheck “uniform scale” when resizing.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000184903/design/2024-01-29_64ef9f2438798.png"></figure>&nbsp;If you want to slice the file manually for use without AMS or other printer please use these settings&nbsp;Print at 100% infill with a layer height of 0.04mm with a base layer of 0.2mm&nbsp;Swap Instructions: Start with Black At layer #7 (0.44mm) swap to Elegoo Blue At layer #29 (1.32mm) swap to Elegoo Yellow At layer #46 (2mm) swap to Elegoo White for the rest.  &nbsp;If you like the print would you please be so kind to give it a rating ? Thanks!&nbsp;Reminder : I share these works for free for hobbyists, you can even print them as gifts for friend and family.If you like my work: a Boost on Makerworld is always appreciated!&nbsp;Or if you want you could give me a tip or &#34;buy me a coffee&#34; on :  <a target="_blank" href="https://ko-fi.com/3deekes" rel="nofollow noopener">https://ko-fi.com/3deekes</a>&nbsp;If you are interested in selling any of my current and future releases send me a message to info@3deekes.be

Art Deco - Minion - Hueforge

Hueforge

3D Senju

This is a L.E.G.O.-Like minifigure lightsaber lamp. It is made 10:1 scale except for the light diffuser which is made to fit within the 256mm print height.This lamp uses the same type of led strip like <a target="_blank" href="https://eu.store.bambulab.com/en-dk/products/ws2812b-rgb-led-strip-light" rel="nofollow noopener">Bambu Lab WS2812B RGB LED Strip Light</a> which is 60 LEDs/M. I have wrapped so the light rod is completely covered in the led strip. With this I have used 102 cm of the led strip.I have tested many variations of size, thickness, diameter and shapes to find one that isn’t too thick but still fades the light. The outer diffuser is made of 3 walls.&nbsp;[It can be recommended to use a higher heat resistant material like PET-G for the Light Rod and Diffuser. I have not had problems with bending but have had a user comment about a bed in his form the heat of his 12V LED strip. If you have PET-G for those parts that will be recommended]&nbsp;Assembly instructions:&nbsp;Step 1Pull the LED-strip through the hole in the light rod, making sure it is rotated the same way as shown in the pictures. Then wrap the LED-strip around the rod as closely as possible, while making sure the adhesive makes good contact. At the end cut the LED-strip where the cobber part is. Finnish off by wrapping a piece of clear tape around the end to help the adhesive not come off.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/523095/2024-02-10_24af65e78a7e1.png"></figure>&nbsp;Step 2Follow the video below by assembling it in the order shown.<figure class="image image_resized" style="width:86.42%;"><img src="https://lh7-us.googleusercontent.com/F8SzaGgSsmr9wRyvrNEC2MxCqsKYJIMkMUjDp11hQIKpV4kCMplV2R8bKpjMhLmrdelXepauUSviVXAbhjkoaMsbkWQR31UNkekoIC20arA8wtfcK85kKPFg-LUC_eNMx07WqffyWeFrWa_SopeMQI8"></figure>Cross section of the assembled lamp:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/523095/2024-02-07_3606fdb4db7e.png"></figure>For those not using my print profile I recommend printing the inner Light Rod lying down as shown in the picture below.<img src="https://lh7-us.googleusercontent.com/DMwQ_q1PUIvkrmzFHOCHGRd4CCXZMrilt_B-T7iJwPhPszTPRwax1zx4TT57Z3lnOb3MWdWfaftQDhFke-W63rM7vADBhtFaTx75kgLDQJh9odtu_SoJXRq3TKthwDthzxq4uNvZ4PVwhjQ1pu1h7oY">This will require more support and make the rod less “round”. But what this has done for me was make the rod stronger and print better. When printing it standing up I found that it wobbled somewhat because of the flexibility in my PLA and therefore made it not completely straight. If you have PET-G or a higher heat resistant material i would recommend to use it for this part and the defuser.&nbsp;If you find the light not to be defused enough I can recommend adding some foam packing material to the inside to defuse it more. I have not used it but it would help if you run into that problem.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/523095/2024-02-11_0d0fc1b3549c.png"></figure>Enjoy :)

Giant LEGOs-Like Lightsaber Lamp (10:1 scale)

Lamps

Sakul

Cozy Minecraft Lamp compatible with the BambuLab Led Lamp Kit. Bring this comfy lantern from your favorite block game to your home and use it as a desk lamp or even as a night light. No glue, screws, or additional parts needed, the complete lamp is assembled with 3D printed clips, making the build process straightforward and fun.No AMS needed. The Lamp Kit can be found <a target="_blank" href="https://us.store.bambulab.com/products/led-lamp-kit-001" rel="nofollow noopener">here</a>! The LED Kit works great with a standard smartphone brick or a power bank, making the lantern a portable option as well. How to build: The whole lantern is assembled using these 3D printed connector clips. You need 14 of those.<figure class="image image_resized" style="width: 31.27%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_5bf6ea8a01c34.jpg"></figure>Print all the parts and start clicking the upper part together. If you need to remove a clip again, it&#39;s best to use some pliers.<figure class="image image_resized" style="width: 85%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_ea97b21669c86.jpg"></figure>Next, connect the side blocks to the bottom part and add the LED light by simply pressing it in from the bottom. There are also some TPU feet you can add to the bottom part, but that is optional.<figure class="image image_resized" style="width: 84.44%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_f5cddf280a52a.jpg"></figure>Now slide the window parts in from the top. You can achieve many different looks by playing around with the choice of color here. For the original looks, normal yellow or blue filament works great.<figure class="image image_resized" style="width: 35.46%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_c310a536111c8.jpg"></figure>Lastly, put the top and bottom part together and enjoy!<figure class="image image_resized" style="width: 35.19%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-01-28_0c134d5dabc89.jpg"></figure>&nbsp;&nbsp;If you like my work and want to support me in creating more free original designs, I would very much appreciate it if you <a target="_blank" href="https://ko-fi.com/sakul" rel="nofollow noopener">“buy me a coffee”.</a>   Check out my newest Uploads:&nbsp;<figure class="table" style="width: 96.81%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/484385#profileId-396742" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-06-04_0f30fee0f9ea4.jpg"></a><figcaption>🍦Pop &amp; Catch Toys Ice Cream Cone🍦</figcaption></figure></td><td><figure class="image"><a href="https://makerworld.com/en/models/457919#profileId-365927" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000161106/design/2024-05-08_184f6d673bf23.jpg"></a><figcaption>🐺🦊Minecraft Forest Animal Pack🐝🐇</figcaption></figure></td></tr></tbody></table></figure>

Cozy Minecraft Lantern for LED Lamp Kit 001

Eriba

Saber3D

*Light Fury not included*&nbsp;Check all my models out at <a target="_blank" href="https://saber-3d.com/" rel="nofollow noopener">www.Saber-3D.com</a> &nbsp;Follow our socials to see new models! &nbsp;<a target="_blank" href="https://www.instagram.com/saber.3d" rel="nofollow noopener">https://www.instagram.com/saber.3d</a><a target="_blank" href="https://www.tiktok.com/@saber3d" rel="nofollow noopener">https://www.tiktok.com/@saber3d</a> &nbsp;Flexi Toothless can Stand, Sit, and Flap Its Wings!&nbsp;It is a great print for those who love to fidget. It does not require supports and prints well in PLA.&nbsp;No Supports necessary!&nbsp;Not all filaments are created equal, If your having issues with wing joints, I suggest increasing or decreasing wing size by 1% until you have the desired fit.&nbsp;For personal non-commercial use only. Please do NOT redistribute the files to anyone else.&nbsp;Want to sell prints or just enjoy the instant access to all my models? join our All Access tier on <a target="_blank" href="https://www.patreon.com/Saber3D" rel="nofollow noopener">Patreon</a>. &nbsp;We really appreciate your support!&nbsp;Please share images of your prints, we love to see them!