skypirate

Downhill_Solutions

<h2>Here is my Poop Pop Stop V2.1! (is also working on X1C now)</h2><h2>Update: 09.Jan.2024:</h2>- I got enough feedback to say it will now also work on X1C!- the front outer wall are now shorter and thinner, no more Z-Homing error- PTFE Cutting tool with fixing clamp for perfect hose length- Optimized tree-supports <figure class="image image_resized" style="width:63.37%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-09_72b3fa75e3ea.jpg"></figure>Notice:The Heatbed has play in the X and Y axes, you can see the GIF. If you have to less space between the Poop Pop Stop and the Heatbed, it can help to pull the bed carefully toward the front door to add some space.<figure class="image image_resized" style="width:46.71%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-09_382c00cd274ba.gif"></figure><h2>PTFE Cutting Tool:</h2><figure class="image image_resized" style="width:41.61%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-09_6556d0a830b0b.jpeg"></figure><figure class="image image_resized" style="width:47%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-09_6fdda886fc02.jpeg"></figure><figure class="image image_resized" style="width:41.35%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-09_bf1bfb070340b.jpeg"></figure><figure class="image image_resized" style="width:45.41%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-09_7bbc6f3b0570c.jpeg"></figure><h3>For the perfect fit and quality like mine, do only use my uploaded printing-profile and ABS filament!</h3> The Problem at my prints was, that the Poop was pulled out of the <a target="_blank" href="https://eu.store.bambulab.com/de/collections/accessories-for-p1-series/products/purge-chute" rel="nofollow noopener">Purge Chute</a> at every filament change:<figure class="image image_resized" style="width:611.234px;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2023-12-21_a9b5c2be80bca.jpeg"></figure> The Solution is my Poop Pop Stop, it lets the nozzle change the filament without problems, and hold the filament waste back in the purge chute:<figure class="image image_resized" style="width:53%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-07_62ff672b725c2.jpg"></figure><h2>The new Version V2.0 is a complete new design of the <a target="_blank" href="https://makerworld.com/de/models/102462#profileId-109116" rel="nofollow noopener">old Version</a> and contins the following changes:</h2>- the bottom layer and the print position are complete new designed without the level change for better print and look.- the poop stop area is now designed with PTFE hoses (you need them seperatly - i used the bambulab spare tubes) against sticking with print filament on the Poop Pop Stop itself.- the poop stop area use now a U-Cut instead of the V-Cut version- the thin front bridge is now stabilized with a vertical wall on the outside of the purge chute.- i added some cutouts in the washing area for the nozzle- the hole at the washing area for the nozzle is now bigger&nbsp;&nbsp;<h2>I tested the new design with a few printing-cubes with arround 50 filament changes and out of different materials (PLA / PETG / ABS), there was no problems on every material at my P1S:</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-07_f764cad86e401.gif"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-07_7542cf135e9a1.jpeg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-07_139fc6ebcdd46.jpeg"></figure><h2>IMPORTANT: This new Version needs some difficult work-steps:</h2>- remove the Support carefully with a knife untill you got a clean surface in this areas- slit the PTFE-hoses lengthwise (only no.2/3/4) , don't slit no.1!- press the tubes in the numbered order on the single part (no.2 you have to press it from the bottom side and turn it carefully onto the round bridge)-after the install of the hoses no.2-no.4, cut it off just to the surface of the component-Cut a radius on the end of the pipe no.1 as shown in the picture (make shure you got a Gap between the hoses arround 1-2mm, if not recut no.1 until the gap is big enough or bend it a little bit) Please do all the steps carfully and check your result for looking the same as my Poop Stop in the pictures!<figure class="image image_resized" style="width:51.96%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-07_241a0ab6f3704.jpeg"></figure><figure class="image image_resized" style="width:51.97%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-09_86dc94b441b87.jpeg"></figure><figure class="image image_resized" style="width:51.36%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-09_a9ab89056c62b.jpeg"></figure><figure class="image image_resized" style="width:51.46%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-07_484e5a68d15d7.jpeg"></figure><figure class="image image_resized" style="width:51.35%;"><img src="https://makerworld.bblmw.com/makerworld/draft/436088/2024-01-07_510df216c2b21.jpeg"></figure>&nbsp;<h2>Please give me feedback! :)</h2>

Poop Pop Stop V2.1 - for P1S / P1P / X1C (UPGRADE 09.01.2024)

Odds and Sods

Lilac Rage

<h3>Santa Mario & Santa Luigi Ornaments</h3>(or Elf Mario depending on who you ask…)Sorry Luigi, but your sprite is exactly the same as your brother's.&nbsp;The perfect 8-bit addition to your Christmas Tree!&nbsp;&nbsp;----------------If you like my stuff, check out my patreon<a target="_blank" href="https://www.patreon.com/LilacRage" rel="nofollow noopener">https://www.patreon.com/LilacRage</a>-------<h3>Instructions:</h3>Print face down on the build plate.Colors used in the print:&nbsp;Mario:<ul><li>IIIDMax Red</li><li>IIIDMax Tan</li><li>Bambu Basic White</li><li>Generic PLA Black (Random Amazon Brand)</li></ul>Luigi:<ul><li>IIIDMax Forest Green</li><li>IIIDMax Tan</li><li>Bambu Basic White</li><li>Generic PLA Black (Random Amazon Brand)</li></ul>&nbsp;----- Be careful using other print profiles than the one provided. I had to slow down the first layer and tweak a few things in order to get the first layer to adhere well. The individual ‘pixels’ are quite small and unless your filament is dry and well tuned, you may have issues with the first layer. I also HIGHLY recommend using a textured PEI plate for the best surface finish and better adhesion.&nbsp;___________ <a target="_blank" href="https://makerworld.com/en/u/2064416831/collections/57254" rel="nofollow noopener">Check Out The Rest of my Ornaments Here</a> ___________ Post Your Makes in the Comments!