sharkattack99

scross01

Pegboard clip to hold metal hooks in place.

Pegboard hook clip

PEGBOARD ACCESSORIES 

Boosted

Castle XLX2 Mounting plate for an Xmaxx.

XLX2 Xmaxx Mounting Plate ESC

RC STUFF

DesignCraft

DISCLAIMER: Print profiles NOT created by DesignCraft may contain outdated model versions or suboptimal slicer settings. Use at your own risk! I have no control to moderate or remove these third party print profiles.&nbsp;The Overture v2 print profile is the original print profile updated with a new model. It's a redesign based on user feedback and also uses about 40% less material. Please refer to the Disclaimer above and also please read the Considerations section below.&nbsp;Description:&nbsp;This adapter system wraps the edges of an OVERTURE 1kg 199x66mm cardboard spool in order to:<ul><li>provide smooth rotation within a Bambu Lab AMS</li><li>prevent carboard debris from depositing within a Bambu Lab AMS</li></ul>Features:<ul><li>Reusable</li><li>OVERTURE nameplate for easy identification when reusing</li></ul>Instructions:<ul><li>Print this model twice for a single spool</li><li>Affix one spool ring adapter on each side of the OVERTURE spool</li><li>See attached photos</li></ul>Considerations:<ul><li>Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.</li><li>Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.</li><li>AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">AMS Lid Riser</a> which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on <a target="_blank" href="https://makerworld.com/en/u/243407759" rel="nofollow noopener">my profile</a> or directly here: <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">https://makerworld.com/en/models/33133</a></li></ul>

OVERTURE Bambu Lab AMS Cardboard Spool Adapter Ring

cardboard adaptors 

LordBoos

Night Dragon (Lithophane) - HueForge&nbsp;To celebrate 200 downloads of my <a target="_blank" href="https://makerworld.com/en/models/16099#profileId-15125" rel="nofollow noopener">Night Dragon (Filament Painting) - HueForge</a> model, I recreated this model as a special edition in a form of Lithophane. It still looks good without backlight, but it really pops out when you backlight it!<h4>Printing instructions:</h4>Warning! This model requires very translucent filaments to be used as blue and purple colors and also a mildly translucent white. I used glitter PLA filaments from eSUN and AzureFilm, they are almost like a natural PLA only lightly tinted blue and purple with added glitter. Glitter is not that important, but it still adds a little something to the print. If you use very opaque filaments, it might not allow enough light to pass through and the lithophane might become very dark or not translucent at all. You can still attempt it, but you have been warned.&nbsp;Filament swaps ONLY, no MMU or AMS required, but AMS makes it much easier.Use Original HueForge profile to get the intended look, my models are very sensitive to print settings because of color blending between layers. Every setting and filament changes for AMS are carefully prepared and fine-tuned in the Original HueForge print profile, feel free to change colors, but I recommend not to adjust other settings. If you want to experiment with your own settings or non-original print profiles, for best look print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm.You can use same filaments as I did, or you can experiment with your own.Don't forget to upload a make!<h4>Filaments Used:</h4><ul><li>PLA BambuLab Basic Jade White Transmission Distance: 4</li><li>PLA AzureFilm Glitter Blue Transmission Distance: 7</li><li>PLA eSUN eTwinkling Purple Transmission Distance: 6</li><li>PLA BambuLab Basic Black Transmission Distance: 0.6</li></ul><h4>Swap Instructions:</h4><ul><li>Start with Jade White</li><li>At layer #5 (0.48mm) swap to Glitter Blue</li><li>At layer #12 (1.04mm) swap to eTwinkling Purple</li><li>At layer #19 (1.6mm) swap to Black for the rest.</li></ul>

PEGBOARD ACCESSORIES

RC STUFF

cardboard adaptors

To Print