schulz.achim34

GlennovitS 3D

UPDATE 13. Dec 2023 - Added 12 more sizes! (same lengths, but with a bigger or smaller lid/opening - size 30 and 50. Size 40 is the original) Enjoy!&nbsp;With this simple little print, you can make your bags a lot easier to use in the kitchen! It’s easy to open, pour and close again. Just print and mount on the bag and you are ready to go! No extra hardware needed - all 3D printed. Ready within an hour - almost no reason not to try this ;-)<h2>Overview</h2>The model comes in 18 sizes for now! It's based on the diameter of the lid/opening and the length of the clip. The diameter comes in 3 sizes:<ul><li>30 mm</li><li>40 mm</li><li>50 mm</li></ul>All lengths of the clips in a particular diameter size, uses the same Cylinder and Lid.The clip comes in 6 lengths (currently from XS to XXL). The total length of the different sizes is approx.:<ul><li>XS: 55, 65, 75 mm (depending on the diameter of the lid/openening)</li><li>S: 90 mm</li><li>M: 120 mm</li><li>L: 150 mm</li><li>XL: 180 mm</li><li>XXL: 210 mm</li></ul>For your information, the sizes used on the images are:<ul><li>Pink: 40 - XS</li><li>Yellow: 40 - XL</li><li>Blue: 30 - XS</li></ul>If you have a request for more sizes or other ideas that would make this clip even better, please leave a comment and I’ll get back to you!<figure class="image image_resized image-style-side" style="width:40.53%;"><img src="https://makerworld.bblmw.com/makerworld/draft/450294/2023-12-11_bc82b2a49eaeb.gif"></figure><h2>Assembly</h2><ol><li>Cut a hole in the bag (fx. a hole in the corner just big enough to fit the cylinder)</li><li>Hold the Cylinder in the hole with the thread sticking out.</li><li>Mount the Clip around the bag and Cylinder base</li><li>Screw the Lid on</li></ol><h2>Print instructions</h2>It prints easy and can print with default values. There are some tips though to make it better.<ul><li>Supports: No - the print-in-place hinge prints without supports!</li><li>Walls/perimeters: 3-5 - the more walls, the stronger but more filament is used - so test a see what you find the best.</li><li>Infill: The more infil, the stronger it will be. Mostly needed on the longer Clip versions.</li></ul>&nbsp;Happy printing!&nbsp;<h2>Want to show your support?</h2>You can see all my designs on Printables - and you can become an active supporter. I would really appreciate it!<a target="_blank" href="https://www.printables.com/@GlennovitS3D#join" rel="nofollow noopener">https://www.printables.com/@GlennovitS3D#join</a>

Ultimate Bag Clip (with Lid - easy access!)

wichtig

baberjosef

Hello, this is an optimized very Strong Corner Bracket/Winkel for Aluminium Extrusion Profiles like ITEM in 40x40 size with holes for M6 Screws. I optimized the structur to have the strongest layer lines, how you can see in the pictures below the lines are perfectly lined. If you want any other sizes you can write me and i will try my best ;). I put STL, 3MF for Bambulabs and for Solidworks (if anyone want to change something) in the downloads.

optimized very Strong Corner Bracket/Winkel for Aluminium Extrusion Profiles ITEM in 40x40 M6

40x40

Eli Mamut

The remaining materials can be hanging cliped and used

A1 mini filament clip

a1 mini

The Crafty Maker

I've used the base and arms as-is. Added a pivot joint and clamp holder.Recommended infill:<ul><li>Arms and base: 20%</li><li>Pivot joint and clamp holder: 40%</li></ul>All parts can be printed without support.The hole for the clamp is intentionally thight. The best way to put the clamp in the holder is to heat it up. This way the plastic will melt a bit and secure the clamp.All joints are connected using M5 bolts and nuts.

wichtig

40x40

a1 mini

arbeit