sam.puneet87

Fletch

The Saturn V rocket miniature model developed by NASA to take astronauts to the moon. Some details were omitted due to how small they were or poor results after slicing. Available in both multicolor and single color. The rocket can stand vertically without any support once assembled.&nbsp;This model should fit all Bambu printers. You will need to move the model to the corner on the A1 mini to fit both the model and prime tower.&nbsp;Update 3/14/24 - <a target="_blank" href="https://makerworld.com/en/models/254506" rel="nofollow noopener">Added a stand to display the Saturn V rocket that can be found here</a>.&nbsp;NotesThe antenna is pretty small, be careful when removing from the kit. When pushing the antenna through the third stage, you can cut the tip off if needed. Do not cut the side that prevents the antenna from going through the third stage (the side that has an extra extrusion closest to the Saturn V label). Once the antenna is through the third stage, you can give it light tug to secure it in place.&nbsp;Assembly<img src="https://makerworld.bblmw.com/makerworld/draft/706290/2024-03-01_0c0b17411535b8.jpg">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/706290/2024-03-01_88e6226af64dd8.jpg">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/706290/2024-03-01_c99b1d1591bfb.jpg">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/706290/2024-03-01_c63a7fd7539ff8.jpg">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/706290/2024-03-01_725c5a900205e8.jpg">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/706290/2024-03-01_a0f5646572fbd8.jpg">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/706290/2024-03-01_38eaf64fc600e.jpg">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/706290/2024-03-01_bf8c15a68b8df8.jpg">

NASA Saturn V Kit Card

card kit

goldiesvinyl

each one needs two 6x2mm magnets post print

Duck Magnets

magnets

Neopyx3D

A cute articulated Fennec created to participate in the Animal Frenzy design contest.&nbsp;This model is: PRINT IN PLACE - NO SUPPORTS&nbsp;Testprinter: A1 Mini with a 0.4mm nozzle printed in multicolorFilament for the Testprint: ISANMATE Highspeed PLA coffee (body), Filament Unger anthracite silver (eyes and nose)&nbsp;This download is for personal and non-commercial use only. Don´t sell my designs or printed designs without permission.If you want to sell your 3D-printed Neopyx3D designs you need a Neopyx3D - Vendor membership via Patreon:&nbsp;https://www.patreon.com/Neopyx3D&nbsp;Recommended Main Settings:&nbsp;Layer height: 0.16 Infill: 15 % Gyroid Supports: No Supports needed Build Plate Adhesion Type: Brim (optional if you have adhesion issues) Printing Temperature and Cooling: depends on filament

Articulated Fennec

animals

VedicFutura

Check out the X1C Print Video here:Instagram Reel: <a target="_blank" href="https://www.instagram.com/p/C0_LTpjymQe/" rel="nofollow noopener">https://www.instagram.com/p/C0_LTpjymQe/</a><figure class="media"></figure>&nbsp;I finally got around to doing this new much requested version of the Ayodhya Ram Temple. I did the first version when the schematics were made public in 2019 at the Kumbh Mela in Prayagraj. Now as the temple is due for inauguration in 2023, I present to you new versions that are much easier to print. This new version has thicker columns, 2.5mm sq at 100% scale. NO SUPPORTS ARE REQUIRED.&nbsp;The original free 210mm version had slender columns and many people had trouble with the print on basic bedslingers. However the STL was extensively tested and even today a Featured model on a popular 3D model repository. Nevertheless to make the model more accessible I have updated it and now its a super reliable. &nbsp;Update #8<ol><li>Bambu Lab A1,X1C Print profiles for both versions (With and without columns) created and uploaded</li><li>Previous version where front steps didn't print was removed and replaced</li><li>Instagram video link shared</li></ol>Update #7<ol><li>The front and side steps were missing after slicing. This is now fixed. Note that the file in the zip folder is the old version. The new version is “Full_210mm_THICKER_COLUMNS_FIXED.stl” and you can find it in the root folder.</li><li>Also updating the preview images with a brighter render</li></ol>Update # 6 (continued from the Free version)<ol><li>New Version with much thicker columns! Many non Prusa printers had trouble printing the columns. Bambu Lab printers ofcourse print this easily. So in this version the column thickness is increased to 2.5mm square.This should allow for a higher margin of error and ensure printing on a variety of printers. Two versions included, with and without flag. Two flag designs also included. There's also a 3mf file with flag oriented to print properly.</li><li>New Version with NO COLUMNS! This version has all the volume between the columns filled in. So its essentially sealed on all sides while still showing the outer columns in profile. This means there is no overhangs or bridging. This version will be the easiest to print and only slightly less beautiful. Two versions, with and without flag. 3mf included.</li><li>New Five Part Version with thicker columns This is the same essential model as (1) but pre split into five separate parts. The parts will help with printing larger sizes.</li><li>Also Included is the Eight Part Version from the original Free post. Here the column size is 2x of the original and should print just fine on most printers. This version is primarily for Extra large size printing. Included for your convenience.</li><li>The original free version also included in the package.</li></ol>For for those who are discovering this model/structure only recently, here's a little background:The Ayodhya Ram Temple, is a Hindu temple dedicated to Lord Ram located in Ayodhya, Uttar Pradesh, India. Its significance lies in the belief that it stands at the birthplace of Lord Ram, a revered deity in Hinduism.The structure is designed in the North Indian Negara architectural style which is vertically oriented, with the Shikara (tower) being the central focus. This verticality symbolizes the ascent towards the divine.The main temple is 235 feet (72 m) wide, 360 feet (110 m) long and 161 feet (49 m) high. The temple complex is the world's third largest Hindu shrine. The building will have a total of 366 columns. The columns will have 16 idols each to include the incarnations of Shiva, the 10 Avatars of Vishnu, the 64 Chausath Yoginis, and the 12 incarnations of the goddess Saraswati. The original design for the Ram temple was devised in 1988 by the Sompura family of Ahmedabad.The construction of the Ayodhya Ram Temple is seen as a momentous event for Hindu devotees and a symbol of religious and cultural revival. It also represents an important chapter in India's history due to the resolution of the contentious Ayodhya dispute.Learn more here: <a target="_blank" href="https://swarajyamag.com/news-brief/nagara-architecture-of-ayodhyas-magnificent-ram-mandir-explained-with-pictures" rel="nofollow noopener">swarajyamag.com/news-brief/nagara-architecture-of-ayodhyas-magnificent-ram-mandir-explained-with-pictures</a> <a target="_blank" href="https://en.wikipedia.org/wiki/Ram_Mandir" rel="nofollow noopener">en.wikipedia.org/wiki/Ram_Mandir</a>&nbsp;Video Link for the Making/Printing of the ORIGINAL model: <a target="_blank" href="https://youtu.be/sEfSoRJSK-w" rel="nofollow noopener">youtu.be/sEfSoRJSK-w</a>&nbsp;If you liked the original model, consider supporting VedicFutura by purchasing this new version. For commercial 3D printing rights, please subscribe to our Patreon or MMF Tribe. New Models Drop On Cults & MyMiniFactory every month!50% off for Patreon and Tribe members.@VedicFutura <a target="_blank" href="https://linktr.ee/vedicfutura" rel="nofollow noopener">Linktree</a> @VedicFutura <a target="_blank" href="https://www.vedicfutura.com/" rel="nofollow noopener">Website </a>&nbsp;Follow to get the latest updatesInstagram <a target="_blank" href="https://www.instagram.com/vedicfutura/" rel="nofollow noopener">@VedicFutura</a> YouTube <a target="_blank" href="https://www.youtube.com/@VedicFutura?sub_confirmation=1" rel="nofollow noopener">@VedicFutura</a>

[New Version!] Ayodhya Ram Temple - No Supports Required! Easy Print!

jai sri ram

low poly

Valeria Momo

My BambuStudio AMS ready print profile is loaded in the "Raw Model File" section. If you print the profile I would be happy if you will upload it as a new print profile.&nbsp;LightBox Google TREX, Size: 21.0*22.0*3.0 cm. It has 2 holes at the back for hanging on the wall. I suggest using 5v led (It has a hole to pass the LED cable through).<h3>Lightbox Desk Stand</h3>If you want to hang the lightbox on your desk or shelf, try my <a target="_blank" href="https://makerworld.com/en/models/149905#profileId-163553" rel="nofollow noopener">Lightbox Desk Stand</a>.<figure class="image image_resized" style="width:249.203px;"><img src="https://makerworld.bblmw.com/makerworld/draft/479432/2024-01-21_610e23f2afe3a.gif"></figure><h3>Commercial license</h3>Do you want to sell prints of this model? You can purchase commercial licensing for this model<a target="_blank" href="https://patreon.com/ValeriaMomo?utm_medium=clipboard_copy&utm_source=copyLink&utm_campaign=creatorshare_creator&utm_content=join_link" rel="nofollow noopener"> by joining the Commercial License in my Patreon</a>.

Google Trex Lightbox

trex

Gallus Design

This partial of Statue of Liberty designed to be tea light holder.&nbsp;Total height of print is 245 mm and suitable for regular size tealight (37mm diameter & 13mm height). &nbsp;I also design full size of statue with giant torch:<figure class="image image_resized" style="width:22.17%;"><a href="https://makerworld.com/en/models/179175#profileId-197044" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/515936/2024-02-10_d71d11ed48f59.jpg"></a></figure>

Statue Of Liberty Tealight Stand

new york

christofer.jh

The one ring, need I say more?&nbsp;Hang on the wall or just put it on a table. The ring is a whole 160mm in diameter!&nbsp;I printed with Bambu PLA silk - Gold.&nbsp;<h2>Current version 2.0 - Now better shine!</h2>Warning, the new back plate is much more secured when inserted. Make sure led is installed before closing.&nbsp;The assembly is easy, just take about 50cm led strip and put it in the ring, like this:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163169/design/2024-02-14_9d0f0db27d1.jpg"></figure>Or alternative slide it in above the internal “bride”, this way you can get two loops for more light.&nbsp;Holder remixIf you want a stand take a look at this remix: <a target="_blank" href="https://makerworld.com/en/models/467240#profileId-376287" rel="nofollow noopener">https://makerworld.com/en/models/467240#profileId-376287</a><h3>Revisions:</h3>v 2.0Total redesign of the inner space of the ring and the back plate. The led strip is now held in place which gives a more uniform shine. Slightly bigger radius on the top of the ring.The back plate also snaps to the ring better, DON&#39;T PUT ON UNTIL LED IS INSERTED.v 1.1<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163169/design/2024-01-30_7d6ab2acdbc06.jpg"></figure><ul><li>Added a optional back plate that snaps in place. Use the chord for hanging on wall, or drill a hole for a nail (or use bambu studio and add a hole)</li></ul><figure class="image image_resized" style="width: 23.9%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163169/design/2024-01-31_2e6cf6cbfd73d.jpg"></figure><figure class="image image_resized" style="width: 24.71%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163169/design/2024-01-31_e9eca6e2a85f3.jpg"></figure>

The one ring - The Lord of the Rings

lotr

Titan3DPrintingAU

Single bed print of a Mandalorian Helmet. Have included the Raw files as well as the file broken up (in RAW form)

Mandalorian Helmet

helmet

starwars

bennny

I modeled this stackable coaster design awhile ago and I had been looking for something to print on them. While at a bar I saw they had some branded coasters with beer logos and that made me want to print some of my favorite cheap/light beers!&nbsp;I currently have 13 different (although there are 2 Miller Lite versions) 3MF's available for download. Some are very easy (not very fine details) to print while others are much hard (lots of very fine details), and some inbetween. I have indicated their difficulty to get a successful print next to their brand names. <ol><li>Budweiser (HARD)</li><li>Coors Light (EASY)</li><li>Heineken (MED)</li><li>Michelob Ultra (MED)</li><li>Miller Lite V1 (EASY)</li><li>Miller Lite V2 (HARD)</li><li>Miller High Life (EASY)</li><li>Guinness (EASY)</li><li>Shiner Bock (MED)</li><li>Bud Light (EASY)</li><li>Rolling Rock (HARD)</li><li>Sol (EASY)</li><li>Dos Equis (EASY)</li></ol><h3>Tips For A Successful Print</h3>Some of these print are genuinely difficult to to get to print right and require good filament calibration and some trial and error. Print profiles simply cannot account of all the different unique variables for each printer and printing environment. The first layer is printed at 0.3mm width, which is significantly less than Bambu Studio's default 0.52mm width. This means good bed adhesion is incredibly important. <ol><li>Make sure your print bed is clean and if you are using glue it is PROPERLY applied. I use the Textured PEI Plate from Bambu Lab, which gives a nice finish, in my opinion, and has good adheasion. Make sure you watch the bed between prints or at least wipe down the plate with isoproply alcohol between prints.</li><li>Turn off the Auxiliary Fan. This coaster model really wants to warp and the excessive cooling from the aux fan will guarantee warping. You can do this in your printer settings at the top of Bambu Studio (or Orca Slicer) and create a new profile named NO AUX FAN or you can manually disable it during the print, but I would reommend changing it in the print profile itself so you don't forget.</li><li>Keep the door closed/barely cracked if you have a P1S or X1C. If you have a P1P or A1 series printer, just do your best to prevent air drafts from passing of your print bed, because that will lead to warping. As always, you know your printer, so just use your own knowledge on how to get successful prints. </li><li>Go SLOW. The first layer has a travel speed of 25mm/s to reduce the amount of stringing and increase the chance of solid contact. I use Orca Slicer when originally making these, which has an option to slow down the first few layers, whereas Bambu Studio does not have this option. Your mileage may vary here and this is going to depend person to person and printer to printer, so apply your own knowledge of your printer and environment. </li><li>Increase bed temperature. PLA typically prints on Bambu Lab printers at a default 55 degrees celsius. I bumped this up to 60 degrees and basically eliminated warping from my prints (if you look closely in the pictures you can see warping on some of the coasters, those were earlier prints as a refined the profile and printing environment). </li></ol>If you follow these tips, you will maximize your chance at a succssful print. While some of these coasters are very easy prints and broad details that any printer can handle, others are quite intricate and require a skilled printer to get good results with. I would watch the first layer go down and stop it if I noticed an issue.&nbsp;I request that people DON'T upload other profiles, because what works for you will not work for someone else. I gave the best possible profile already to ensure success, but it may require manual tweaking from the individual users to get the print they want.&nbsp;If you have any brand requests, questions, or printing advice, please leave them in the comments or DM me. &nbsp;Thanks and happy printing!

Stackable Beer Brand Coasters

DylansLightBoxes

Deadpool Light box. Easy to print, one plate for the lid and one plate for the back. Simply add a 1m white led strip and you have a great light box! The hole on the back is designed to fit a 20mm wire grommet (easily found on amazon).&nbsp;

Deadpool Light Box

lightbox

angry-p1p

&nbsp;This ist my first attempt designing an articulated dratini (multicolor version) - no supports, no assembly needed.&nbsp;You may have to reduce the printing speed for the pointy ears and make sure you activate brim type “outer brim only” otherwise the lower part of the ears come loose.&nbsp;Default size is 32x150x25mm&nbsp;If you want to sell 3D prints please become a <a target="_blank" href="https://www.patreon.com/angryp1p/membership" rel="nofollow noopener">Patreon</a> and start selling :)&nbsp;RAW .stl for non Bambu Users available! <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000147391/design/2024-02-13_9ed7d46333a48.jpg"></figure>More related prints: Shellder/Muschas <figure class="image image_resized" style="width: 32.04%"><a href="https://makerworld.com/en/models/244869" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000147391/design/2024-03-11_945e3063d8015.jpg"></a></figure>  Articulated Dragonair <figure class="image image_resized" style="width: 24.38%"><a href="https://makerworld.com/en/models/221657" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000147391/design/2024-03-03_eac5d40844b61.jpg"></a></figure>&nbsp;Articulated Gyarados <figure class="image image_resized" style="width: 34.31%"><a href="https://makerworld.com/en/models/193723" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000147391/design/2024-02-20_de90d12bd3fa1.webp"></a></figure>&nbsp;&nbsp;&nbsp;Keychain version <a target="_blank" href="https://makerworld.com/en/models/180339" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000147391/design/2024-02-10_7fc4cc0b412b5.jpg"></a>&nbsp;&nbsp;Pikachu Key Chain <figure class="image image_resized" style="width: 30.75%"><a href="https://makerworld.com/en/models/179448" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000147391/design/2024-02-10_33ef3f8ce178b.jpg"></a></figure>&nbsp;One Color Version:&nbsp;<figure class="image image_resized" style="width: 36.92%"><a href="https://makerworld.com/en/models/147389" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000147391/design/2024-01-19_2dfa09fb73b2f.jpg"></a></figure>&nbsp;More Pokemon related prints: <figure class="image image_resized" style="width: 23.43%"><a href="https://makerworld.com/en/models/124972" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000147391/design/2024-01-28_0b24300abf65.jpg"></a></figure> <figure class="image image_resized" style="width: 41.09%"><a href="https://makerworld.com/en/models/81994" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000147391/design/2024-01-28_8059aa8533b21.jpg"></a></figure> &nbsp;

Articulated Dratini Multicolor

minis

Jhos Fuentes

Lockheed F-117 Toy

aircraft

jarvizar

3D miniature of Midtown Manhattan!&nbsp;Model spans from the East River to the Hudson river & 25th St. to 60th St.&nbsp;&nbsp;Check out my collection of other Large miniature cities: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/468505" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/468505</a>&nbsp;New York City miniatures collection: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/177621" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/177621</a>&nbsp;&nbsp;This model was designed to be printed with a 0.4mm nozzle and 0.16mm layer heights. Try using a 0.2mm nozzle (0.08mm layer heights) or scaling up for even finer detail!&nbsp;Note: If roads or other small details disappear after slicing, try lowering the extrusion/line width of external perimeters (outer walls) closer to 0.4mm OR use Arachne walls.&nbsp;<h2>Framing Details</h2>&nbsp;This model measures almost exactly 7.5x9.5in (241.32mm X 191.08mm) and should fit most 8x10 frames (assuming frame lip/overlap is around a half-inch). Feel free to change the scale/size of the model(s) to meet your needs.&nbsp;Personally I use these cheap wooden frames from Amazon: <a target="_blank" href="https://www.amazon.com/dp/B08XVP48KQ" rel="nofollow noopener">https://www.amazon.com/dp/B08XVP48KQ</a>And blue printer paper: <a target="_blank" href="https://www.amazon.com/Astrobrights-491618-Multipurpose-8-5-Inch-11-Inch/dp/B00006IDQT" rel="nofollow noopener">https://www.amazon.com/dp/B00006IDQT</a>&nbsp;I also included a large printable frame (w/ 1mm water plate) designed to fit my large miniature cities.&nbsp;Note: This is a “large” miniature and will not fit the smaller ~5x7inch printable frame included with the other miniature cities!&nbsp;A frame is not required! This model looks great by itself and can be displayed almost anywhere.&nbsp;

New York City Manhattan (Large 8x10)

city miniatures

RynosaurusRex

Hello space travelers. Here is my 140 mm Jupiter.<ul><li>Must use 100% infill</li><li>Inner and outer brim recommended since there is not much surface area</li><li>No supports Required</li></ul>Uncut Version in Raw Model Files so you can plane cut for whatever size light your gonna use&nbsp;Travel to <a target="_blank" href="https://makerworld.com/en/models/151417" rel="nofollow noopener">Mars</a>&nbsp;Go large and print at 150% and use <a target="_blank" href="https://makerworld.com/en/models/161426" rel="nofollow noopener">nadnerb33's</a> rotating stand

Jupiter

lith

3D design shop

After a long journey, I've finally completed my flexible skeleton dragon.&nbsp;It's a fun piece of toy that's incredibly flexible, with virtually all joints capable of movement. It has become a huge hit with the kids at home!&nbsp;I printed it on a smooth surface, which eliminates potential issues with adhesion on a textured bed. If adhesion problems persist, I recommend adding a brim.&nbsp;Improved version

Articulated Skeleton Dragon

skeletal

Peprinter

IT crowd signSuitable for most IT offices

IT crowd sign

3DP RNS

★ New Robot Unveiled!&nbsp;[3DP RNS] Spi V1.0 (3D Printed Robot)<ul><li>Series : 6 Legs / 6-Legged Spider Type [<a target="_blank" href="https://youtube.com/shorts/I7V7X6KWw58?feature=share" rel="nofollow noopener">Youtube Video</a>]</li><li>This Is an all at once print. Assembly not required :)</li><li>If you subscribe to the YouTube channel [<a target="_blank" href="https://bit.ly/2KC3Tdx" rel="nofollow noopener">3DP RNS</a>], ★ a new robot will be revealed.</li><li>Thank you for your subscribing! It means a lot to me :)</li><li>Commercial License [<a target="_blank" href="https://www.patreon.com/3DPRNS" rel="nofollow noopener">Patreon</a>]</li></ul>&nbsp;※ Notice For my uploaded robot model to enable all joints to move, it&#39;s advisable to use a Brim.  If removing Brim is inconvenient or challenging, I don&#39;t recommend printing it.  Also, joint functionality may vary depending on the printer and filament you use. I hope your print is successful and you can have a robot with well-functioning joints.<figure class="media"><oembed url="https://www.youtube.com/shorts/I7V7X6KWw58"></oembed></figure>ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ[3DP RNS] Venom Weaver V1.0 (3D Printed Robot)<ul><li><a target="_blank" href="https://www.patreon.com/posts/3dp-rns-venom-v1-102280396?utm_medium=clipboard_copy&amp;utm_source=copyLink&amp;utm_campaign=postshare_creator&amp;utm_content=join_link" rel="nofollow noopener">[3DP RNS] Venom Weaver V1.0 Download [Patreon]</a></li><li>Venom Weaver V1.0 can be obtained through Patreon (Hero) membership.</li><li>Venom Weaver is a spider-like robot with eight legs that moves quickly. It can emit venom or explode to spread poison. It&#39;s dangerous, so avoid it if you encounter one.</li></ul><figure class="media"><oembed url="https://www.youtube.com/shorts/MX6lzRMSDXo"></oembed></figure>ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ[3DP RNS] Crawler V1.0 (3D Printed Robot)<ul><li><a target="_blank" href="https://www.patreon.com/posts/3dp-rns-crawler-104482987?utm_medium=clipboard_copy&amp;utm_source=copyLink&amp;utm_campaign=postshare_creator&amp;utm_content=join_link" rel="nofollow noopener">[3DP RNS] Crawler V1.0 Download [Patreon]</a></li><li>Crawler V1.0 can be obtained through Patreon (Hero) membership.</li><li>It is a hexapod robot with long legs, allowing it to move quickly. High-performance sensors are installed on its legs and body, providing excellent detection capabilities.</li></ul><figure class="media"><oembed url="https://www.youtube.com/shorts/nqp_DcHcsJk"></oembed></figure>

[3DP RNS] Spi_V1.0

robotics

LemonArts

This is my Remix from M-Power1970 T1 Pencil holder. <figure class="image image_resized" style="width:72.44%;"><img src="https://makerworld.bblmw.com/makerworld/draft/389575/2024-01-11_b32890627673e.jpg"></figure> This is a optimized version. The following things have been adjusted to the model: - Added 3d Model Wheel Axle- holes adjusted- adhesive aid created for the roof Instructions: Put the adhesive aid in the hole for easier assembly<figure class="image image_resized" style="width:33.81%;"><img src="https://makerworld.bblmw.com/makerworld/draft/389575/2024-01-11_e344e2bfbec8.jpg"></figure><figure class="image image_resized" style="width:33.15%;"><img src="https://makerworld.bblmw.com/makerworld/draft/389575/2024-01-11_e866eaadffab1.jpg"></figure>&nbsp;Press the Wheels on the rims. This requires a lot of pressure&nbsp;<figure class="image image_resized" style="width:32.97%;"><img src="https://makerworld.bblmw.com/makerworld/draft/389575/2024-01-11_3ff5d2145996a.jpg"></figure>&nbsp;Press the Axles in the holes&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/389575/2024-01-11_836e0ac248819.jpg"> press the wheels on the axles <figure class="image image_resized" style="width:34.19%;"><img src="https://makerworld.bblmw.com/makerworld/draft/389575/2024-01-11_79869918e8f29.jpg"></figure> the rest is self-explanatory. Just use some superglue and stick it on

VW T1 Bus Pickup Pen / Desk Organizer USB SD microsd

stationary 

lasse1999

Container for especially cotton swabs, when you are traveling or on the go. Can be used for much more. Remember to check out my matching container for cotton swabs.