s.epple

BamBam Design

<h4>The Sunflower Windmill - Self adjusting Sunflower wind turbine</h4><figure class="media"><div data-oembed-url="https://youtube.com/shorts/Nb2DXeNK04M?si=IG2UF_6DRZEUfwdW"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=Nb2DXeNK04M"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/Nb2DXeNK04M" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>Need a bit more wind, but can turn fast as well. Great spring &amp; summer garden decoration<ul><li>Beautiful Windmill with a Sunflower Propeller Design</li><li>Self adjusting to wind direction through the Tail Blade</li><li>100% printed, no Screws or tools needed</li><li>You can add 2 Propellers on one Axle with 2 distances</li><li>Choose your propeller sizes and directions (You get nice effects if you choose different directions)</li><li>Rods are stack able to your needed height</li></ul><h4>Printing:</h4>The rod could be a bit difficult to print, i added custom support, but clean your buildplate and apply some glue.&nbsp;Profile is tested with PETG &amp; PLA 👍🏼 Prefer PETG for Axle and Rod&nbsp;Info:This time the Axle is a bit shorter to add only 2 propeller with 10mm and 2 distances with 5mm each.And i slightly redesigned the tail blade to match the sunflower design. My other windmills are still fully compatible if you want to mix it up:<ul><li><a target="_blank" href="https://makerworld.com/models/235261" rel="nofollow noopener">Toroidal Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/250216" rel="nofollow noopener">Honeycomb Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/388124" rel="nofollow noopener">Elliptical Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/425419" rel="nofollow noopener">Sunflower Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/454861" rel="nofollow noopener">Raccoon Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/255324" rel="nofollow noopener">CLAMP for Windmills</a></li></ul><h4>Assembly:</h4><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425419/design/2024-04-12_5daa8d4f64298.png"> Thanks to all followers and don&#39;t forget the virtual handshake 👍 ….Happy Printing&nbsp;Some other Windmill Designs:<a target="_blank" href="https://makerworld.com/en/models/454861" rel="nofollow noopener">Raccoon</a><figure class="image"><a href="https://makerworld.com/en/models/454861" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425419/design/2024-05-06_9785fb508d759.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/250216" rel="nofollow noopener">Honeycomb</a><figure class="image"><a href="https://makerworld.com/en/models/250216" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425419/design/2024-05-06_9a2a48a0331ed.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/235261" rel="nofollow noopener">Toroidal</a><figure class="image"><a href="https://makerworld.com/en/models/235261" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425419/design/2024-05-06_ca5dfbc30c041.jpg"></a></figure>&nbsp;Checkout this Clamp for windmill, as well🧐 <a target="_blank" href="https://makerworld.com/models/255324" rel="nofollow noopener">https://makerworld.com/models/255324</a><a target="_blank" href="https://makerworld.com/en/models/255324" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425419/design/2024-03-15_6d9c46a2c3e8c.jpg"></a>&nbsp;Commercial license you can get here:<a target="_blank" href="https://www.patreon.com/BamBamDesign/membership" rel="nofollow noopener">https://www.patreon.com/BamBamDesign/membership</a>

Sunflower Windmill - Customizable System

Emma

dutchwoody

A simple hook for Skadis to store thread and yarn. 10 hooks fit on a Voron 0 buildplate.It is a real tight fit to make sure that everything stays in place.Angle is 45 degree. Larger bobbins will also fit.

Skadis thread hook for bobbins

Nähen 

MplusM

UPDATE:This model has been replaced by version v2 Plus. Download: <a target="_blank" href="https://makerworld.com/en/models/419236" rel="nofollow noopener">https://makerworld.com/en/models/419236</a>&nbsp;After so many people asked me for my Marble Run 003 expansions and I was not allowed to pass them on, I designed this Paddle Wheel Addon. Based on my improved “jump catcher”, there is now a track extension with a paddle-wheel as an Addon, which btw - from my point of view - shouldn&#39;t violate the license terms of the original Marble Run 003 model <a target="_blank" href="https://makerworld.com/en/models/14265" rel="nofollow noopener">https://makerworld.com/en/models/14265</a> .&nbsp;This track is clearly a shortcut and the marbles that take this route overtake all the other marbles. That&#39;s why I&#39;ve drawn it so that not many marbles go that way. Also, the lower part of the track is slightly uphill and then has only a slight slope in order to reduce the rolling speed. On the other hand this can cause the marbles to get stuck, depending on the print quality or the uneven surface. If this is the case, you just have to warm up the lane (serpentine) with a hairdryer and bend the curve down a little.I would be grateful if you share with me your suggestions and experiences.&nbsp;Notes:<ul><li>This addon contains small parts. Please make sure that children cannot swallow them.</li></ul>&nbsp;Print Instruction and Assembly:<ul><li>Please refer to the instructions in the attached pdf.</li></ul>&nbsp;More control:Do you prefer more control over marbles that take the shortcut? Check out the “Jump Catcher v1B” with adjustable opening (“sliding door“): <a target="_blank" href="https://makerworld.com/en/models/386909" rel="nofollow noopener">https://makerworld.com/en/models/386909</a>&nbsp;Interested in more Marble Run items? Check out <a target="_blank" href="https://makerworld.com/en/@mplusm" rel="nofollow noopener">https://makerworld.com/en/@mplusm</a>&nbsp;&nbsp;

Marble Run 003 Paddle Wheel Addon v1

Samu 

hologos

Wall hanger for an ironing board with curved legs. Use four 6mmx50mm half round head screws.<h3>Print Settings</h3>Material: PLA Layer height: 0.2 mm Perimeters: 4 Top layers: 4 layers Bottom layers: 4 layers Infill: 25% Supports: no (if you have decent cooling) Brim: yes (good practice with thin and tall objects)<h3>Print Instructions</h3>Print on the side so the layer lines are perpendicular to forces (gravity). Use brim to help bed adhesion.&nbsp;<figure class="image image_resized image-style-align-left" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/124852/2023-10-27_zcdqexlr2b3p.png"></figure>

Wall Hanger for Ironing Board with curved legs

Haushalt

Markus710

Vase

Vasen 

Xtreme73

English and italian description&nbsp;EnglishPyramid paint spraying standThis pyramid paint spraying stand is an ideal accessory for professional painting. It is made of lightweight and durable pla material, and can be 3D printed without supports.The stand consists of three or more pyramids that interlock to form a stable base. The pyramids have a conical base that allows you to support the object you want to paint in a safe and uniform way.Using this stand is simple and intuitive. Just place the object you want to paint on the base of the pyramids, and start spraying the paint. The pyramidal shape of the stand allows you to achieve a uniform distribution of the paint, avoiding drips and smudges.Main features:<ul><li>Made of lightweight 1 Gram! strong design</li><li>Fast and support-free 3D printing</li><li>Conical base for a safe and uniform support</li><li>Uniform paint distribution</li></ul>&nbsp;ItalianoStand per spruzzatura della vernice a forma di piramideQuesto stand per spruzzatura della vernice a forma di piramide è un accessorio ideale per la pittura professionale. È realizzato in materiale PLA leggero e resistente, e può essere stampato in 3D senza supporti.Lo stand è composto da quattro o più piramidi che si incastrano tra loro per formare una base stabile. Le piramidi sono dotate di una base conica che consente di appoggiare l'oggetto da colorare in modo sicuro e uniforme.L'utilizzo di questo stand è semplice e intuitivo. Basta posizionare l'oggetto da colorare sulla base delle piramidi, e iniziare a spruzzare la vernice. La forma piramidale dello stand consente di ottenere una distribuzione uniforme della vernice, evitando sbavature e gocciolamenti.Caratteristiche principali:<ul><li>Progettato in modo da essere leggero 1 grammo! e resistente</li><li>Stampa 3D veloce e senza supporti</li><li>Base conica per un appoggio sicuro e uniforme</li><li>Distribuzione uniforme della vernice</li></ul>

Paint spraying stand, ultralight and strong

Werkstatt 

Fugge84

Here's a cute but damn big decorative bunny&nbsp;Total size 78 cm&nbsp;There are other sizes to follow, but they first have to withstand my pressure.25cm/50cm/18cm&nbsp;Have fun printing&nbsp;Ein neuer Hase ist fertig gewordenMeine Frau Liebt ihn&nbsp;<figure class="image image_resized" style="width:47.5%;"><img src="https://makerworld.bblmw.com/makerworld/draft/704488/2024-03-14_2910b342fdfbb8.jpg"></figure>

Big Easter Bunny 78cm/ 30,71 inch / Oster Hase 

Ostern

valinalo82

Christmas decoration snowflake. print from white PLA. Layer 0.3mm

Christmas decorations - Snowflake

Weihnachten 

Urban 3D

12/9/2023 - updated to provide a better chute to prevent material from becoming stuck&nbsp;This is a highly revised version of my previous pull tray purge bucket. Ths model requires NO supports. After some user review, this model features a steeper angle on the chute, as well as a drastic reduction in material required to print! It also features slots for two 3x9 magnets to secure it to the back of the printer!