rolando

Soap_Warrior

香蕉爪刀 摘要：这是一把以香蕉为原型，结合伸缩爪刀而设计的香蕉爪刀，不需支撑方便打印，除了3D打印的零件之外，还需要两个直径10mm厚度2mm的磁铁。 Abstract: This is a banana claw knife based on the prototype, combined with the design of the telescopic claw knife, which is convenient for printing without support, in addition to the 3D printed parts, it also needs two magnets with a diameter of 10mm and a thickness of 2mm.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_5663645a5bc53.gif"></figure> 主要零件：香蕉1*1、香蕉2*2，香蕉刀刃*1、连接块*1、直径10mm厚度2mm磁铁*2，如下图所示： Main parts: banana 1*1, banana 2*2, banana blade*1, connecting block*1, diameter 10mm thickness 2mm magnet*2 as shown in the figure below:<img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_c2547b7f91a85.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_8c182f640bb7e.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_23c7e3e309af8.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_e9d884e12d496.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_31d257e313e9c.jpg"> 组装过程：1.将磁铁装入香蕉1零件的2个凹坑内，并使用胶水固定。注意：保证两磁铁相吸！ Assembly process: 1. Load the magnet into the 1 pit of the banana 2 parts and fix it with glue. Note: Make sure the two magnets attract!<figure class="image image_resized" style="width:50.42%;"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_64b61a5eb48e2.jpg"></figure> 2.将香蕉刀刃装入香蕉1零件，确保刀刃能够正常滑动。 2. Load the banana blade into the banana 1 part and make sure the blade slides properly. <img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_b69a26ab655a8.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_77246da017ec7.jpg"> 3.将连接块卡入香蕉2零件中并用胶水固定。（最新的连接块为了方便安装两端增加倒角）。 3. Snap the connecting block into the banana 2 parts and fix it with glue. (The latest connecting block adds chamfers at both ends for easy installation).<figure class="image image_resized" style="width:44.78%;"><img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_97bc91e5d88a5.jpg"></figure> 4.将香蕉2与香蕉1零件进行组装，并使用胶水固定。注意：不要使用过量胶水，可能会导致刀刃粘连！ 4. Assemble Banana 2 with Banana 1 parts and fix them with glue. Note: Do not use excessive glue, it may cause the blade to stick！<img src="https://makerworld.bblmw.com/makerworld/draft/778743/2024-03-28_fb18fe34b9138.jpg">&nbsp;

香蕉爪刀-Banana claw knife

Sebastian

JakeMakes

v2 available <a target="_blank" href="https://makerworld.com/en/models/101422#profileId-108205" rel="nofollow noopener">here</a>&nbsp;*v1.1 Update:<ul><li>Updated the &#34;blade&#34; to have a stronger tip and the filament profiles are geared more toward better layer adhesion. It might be too hot for some brands of PLA, but should work for most.</li><li>Added a pommel and set height layer modifier for a 2nd color if desired.</li><li>I have a v2 that&#39;s nearly ready and I&#39;ll post as a remix.</li></ul>Original DescriptionFirst attempt at a collapsible sword. I definitely have some things I&#39;d like to try for my next go, but it works and looks ok to me, so have fun!&nbsp;I used <a target="_blank" href="https://numakers.com/products/pla-filament?ref=4nyxoesl" rel="nofollow noopener">Numakers PLA+</a> for this and both swords have held up well with two boys sparring on the regular with them.

Print in Place Collapsing Sword

Dagger

scherlund

A set of pegs for the A1 Mini Tool Box:https://makerworld.com/en/models/65527#profileId-68895&nbsp;I didn't have any M3x30 screws at hand, so made a quick set of printet pegs instead.&nbsp;Size:Height: 31mmdiameter: 4 for the first 1mm and 3 for the remaining 30mm&nbsp;Since the original print is made for screws I had to use a 3mm drill to make the holes a bit larger.

Sebastian

Dagger

toola