randomdesigns

linus3d

<h2>Introduction</h2>The <a target="_blank" href="https://makerworld.com/en/models/13806#profileId-129851" rel="nofollow noopener">3D Printable Jet Engine </a>is great! However, I wanted a turbojet or low bypass turbofan to complement the original. So, I got to work designing the turbojet,<a target="_blank" href="https://makerworld.com/en/models/477462#profileId-388528" rel="nofollow noopener"> afterburner and variable exhaust nozzle.</a>&nbsp;This conversion uses fewer screws than the original! It adds an additional compressor stage, making the model longer and thinner. The design philosophy matches the original, with hints of the <a target="_blank" href="https://en.wikipedia.org/wiki/General_Electric_J79" rel="nofollow noopener">GE J79</a> visible in the inlet.&nbsp;I designed a <a target="_blank" href="https://makerworld.com/en/models/477457#profileId-388519" rel="nofollow noopener">stand</a>. Making the jet sit low to the ground. It works great!&nbsp;I made a video and written instructions for assembly. ( Video is more thorough).My print profile uses three colors, but feel free to unleash your creativity.&nbsp;If you don&#39;t yet have the hardware for the Jet Engine, I offer a great kit on <a target="_blank" href="https://linus3d.de/products/jet-engine-components-kit" rel="nofollow noopener">my website</a>. It provides better hardware at a lower cost and greatly supports my work. Thank you.&nbsp;Check out the <a target="_blank" href="https://makerworld.com/en/models/477462#profileId-388528" rel="nofollow noopener">Afterburner &amp; Variable Nozzle!</a>&nbsp;Happy printing and great success! Message me with any questions!&nbsp;<h3>Tools used for assembly:</h3><ul><li>M2 Screwdriver</li><li>Pliers or anything that can hold nuts</li><li>Plastic Glue</li></ul>&nbsp;<h2>Assembly</h2>&nbsp;<figure class="media"><oembed url="https://www.youtube.com/watch?v=q-FUjxFJqak&amp;list=PL8UJHE2kIJR-gfuExW762FB3cbsvxPOr2&amp;index=1"></oembed></figure>&nbsp;<figure class="table" style="width: 79.7%"><table class="ck-table-resized" style="border: 3px solid hsl(150, 75%, 60%)"><colgroup><col><col></colgroup><tbody><tr><td>Pliers aren&#39;t needed for this step. Drop the nuts into the slots and screw in the bolts.</td><td><figure class="image image_resized" style="width: 100%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_a17c81ffcbf94.jpg"></figure></td></tr><tr><td>Use plastic glue. I let the glue dry properly before installing into casing.</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_497a72db2ac2b.jpg"></figure></td></tr><tr><td>Don&#39;t glue them in place yet! :)</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_254d558ab4596.jpg"></figure></td></tr><tr><td>Easy…</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_676037b4e1e44.jpg"></figure></td></tr><tr><td>The bearing will also snap into place.&nbsp;</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_ce9c5144d1a1b.jpg"></figure></td></tr><tr><td>Easy…</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_3fa0e4a28d73.jpg"></figure></td></tr><tr><td>Don&#39;t tighten to much. You want even spacing around the inlet.</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_79e7688b07e24.jpg"></figure></td></tr><tr><td>Easy… (I don&#39;t use glue)</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_42ea63250832d.jpg"></figure></td></tr><tr><td>Last step… Make sure everything works. Congratulations! Thanks for printing!</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_a7de2137028fc.jpg"></figure></td></tr><tr><td>Placement of the engine on the stand</td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000477475/design/2024-05-20_481c8f7cac0b1.jpg"></figure></td></tr></tbody></table></figure>&nbsp;Designed by linus3d My website: <a target="_blank" href="https://linus3d.de/" rel="nofollow noopener">https://linus3d.de/</a>

things to build