pnwhammer

waveman

*** Check out the <a target="_blank" href="https://makerworld.com/en/models/505390" rel="nofollow noopener">Customizable Textured</a> version of this model! ***&nbsp;Infinity cube with strong hinges that won&#39;t break easily. This cube is designed with a lot of slack, so that it moves freely.&nbsp;I designed this after having several fails with other models, where the hinges would break when trying to loosen them after printing. Hopefully, this design will print well for everyone!&nbsp;These models and openscad source file can also be downloaded from <a target="_blank" href="https://github.com/jhpieper/sturdy-infinity-cube" rel="nofollow noopener">https://github.com/jhpieper/sturdy-infinity-cube</a><h3>Post-Printing</h3>The hinges should bent quite easily after printing, with the hinges on the front and back side being more tight due to the orientation. Just work the cube a few times and everything should be quite loose.<h3>Cube Sizes</h3>It is best to not scale the model, as it messes with the spacing in the hinges.Instead, check out these other models optimized for their size:<ul><li><a target="_blank" href="https://makerworld.com/en/models/36109#profileId-33936" rel="nofollow noopener">16: S</a></li><li>20: M -- try this first! This is the most common size.</li><li><a target="_blank" href="https://makerworld.com/en/models/36113#profileId-33940" rel="nofollow noopener">24: L</a></li><li><a target="_blank" href="https://makerworld.com/en/models/36115#profileId-33943" rel="nofollow noopener">30: XL</a></li><li><a target="_blank" href="https://makerworld.com/en/models/36116#profileId-33945" rel="nofollow noopener">36: XXL</a></li></ul><h3>Other Versions</h3><a target="_blank" href="https://makerworld.com/en/models/505390" rel="nofollow noopener">Customizable Textured Infinity Cube</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000021188/design/2024-06-23_8e8ad03b44d33.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/41416#profileId-41687" rel="nofollow noopener">Halloween Sturdy Infinity Cube</a> (two color print with AMS)<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000021188/design/2023-10-15_f2f98325d3a09.jpg">&nbsp;<a target="_blank" href="https://makerworld.com/en/models/31328#profileId-27875" rel="nofollow noopener">Two-faced Sturdy Infinity Cube</a> (two color print with AMS)<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000021188/design/2023-10-15_599e03246b88.png">

Sturdy Infinity Cube

Fidgets

DesignCraft

This model widens one side of the spool ring adapter to stabilize a ACEADDITY 1kg 199x61mm cardboard spool while it rotates within a Bambu Lab AMS.&nbsp;Features:<ul><li>Reusable</li><li>ACEADDITY nameplate for easy identification when reusing</li></ul>Instructions:<ul><li>Measure your spool first to ensure it matches the specified dimensions.</li><li>Print one of each model for a single spool.</li><li>Affix the wide spool ring adapter on the right-hand side of the ACEADDITY spool if you're facing the AMS.</li><li>See attached photos.</li></ul>Considerations:<ul><li>Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.</li><li>Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.</li><li>AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">AMS Lid Riser</a> which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on <a target="_blank" href="https://makerworld.com/en/u/243407759" rel="nofollow noopener">my profile</a> or directly here: <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">https://makerworld.com/en/models/33133</a></li></ul>

Fidgets

Spool Adapters