pixel cup

Hugo

If you need to secure your precious belongings in a safe place, you found what you were looking for. This safe is secured by a 3 digit combination to prevent anyone from opening it (unless they have a hammer or a heat gun, I mean it's just plastic at the end) This is kind of a long build but it is perfect to learn how a combination safe works. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_qic0h1icrn73.gif"></figure><h4>Printing instructions :</h4>Start by printing all the parts I provide, I used PLA with 0.2mm layer height and 20% infill for everything and non support.For some part the printing orientation is quite important for the strength, so this is the orientation for the parts you may have a doubt with :Both axle are printed on the side for better strength :<figure class="image image-style-align-center image_resized" style="width:49.05%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_9soz2jjbv724.jpg"></figure><figure class="image image-style-align-center image_resized" style="width:48.19%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_8l6i2qmusurb.jpg"></figure>The lever is printed like this :<figure class="image image-style-align-center image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_fpchn6fpzgzg.jpg"></figure>Both pivots are printed on the side :<figure class="image image-style-align-center image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_h3179x4t16fp.jpg"></figure>The pins are printed like this :<figure class="image image-style-align-center image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_d2hma44t28dw.jpg"></figure>The latch is printed like this :<figure class="image image-style-align-center image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_tpzanma84mk8.jpg"></figure>All the oher parts orientations should be pretty obvious.<h4>Building instructions :</h4><ol><li>Glue the dial with the disk_1 through the front_plate : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_pvatzay1ysnd.png"></li><li>Add the axle_1, the 2 remaining disks and the spacers, no glue required : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_er517y4une2y.png"></li><li>Glue the pins to each disk. On disk_1 and disk_3 the longer part should be facing towards the centre, and the centre pin is the biggest : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_k9t8edz0d0tj.png"> </li><li>Glue the knob to the axle_2 through the front plate, and then place the lever on the axle : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_8gvq2v99fauw.png"></li><li>Close the door assembly by gluing the back_plate to the front_plate : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_lp2gyrj08tic.png"></li><li>Place the latch over the lever's arm and secure it by gluing the 2 latch guides in their dedicated spot : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_vo0qe07t4477.png"> After this step, the assembly should look like this : <img src="https://media.printables.com/media/prints/259699/rich_content/bfb73901-7871-4b09-b254-c44da65f9763/image.png#%7B%22uuid%22%3A%2224948dac-c192-4727-8163-4e6776323946%22%2C%22w%22%3A1920%2C%22h%22%3A1440%7D"> At this point you can figure out the combination by following these steps : <ol><li>Turn the dial on the lock clockwise three times. This connects the 3 disks together, so they now turn with the dial.</li><li>Continue to turn the dial clockwise until the notch on the disk_3 is lined up with the lever. Stop and look at the dial to write down the first number of the combination.</li><li>Turn the dial counterclockwise for 1 full turn past the first number to engage the middle disk.</li><li>Continue to turn the dial counterclockwise until the notch from the middle disk lines up with the lever and stop to write down the second number of the combination.</li><li>Finally, turn the dial clockwise until the notch from the first disk lines up with the lever. All 3 notches should now be aligned. Write down the third number of the combination. You should now be able to turn the knob and unlock the mechanism.</li><li>Test your combination by unlocking the mechanism without looking at the disks. You can follow these instructions if you don't know how to : https://www.google.com/amp/s/www.wikihow.com/Open-a-Combination-Lock%3famp=1</li><li>Keep the numbers of the combination somewhere as it will never change. </li></ol></li><li>Glue the 2 pivots to the door assembly : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_3qdtt9kxxv8n.png"></li><li>To assemble the box start by placing the top and bottom walls on the pivots (no glue) : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_zbo1w07q7294.png"> </li><li>Glue the 2 side walls : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_9sjsq7gxjpmu.png"> When gluing the sides, do it with the door closed so you can see that everything is well centered. At this point you should test to lock and unlock the door a couple of times to test the combination before gluing the back_wall. </li><li>When you are sure of the combination you can glue the back_wall to finish the safe : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_rxxxpzkjo5kx.png"></li></ol>&nbsp;&nbsp;

Safe box - 3 digit combination

I like

3DP RNS

[3DP RNS] Worker V1.2 (3D Printed Robot)<ul><li>Strengthening the torso and knee joints.</li><li>Refinement of the sharp edges of the elbows</li></ul>ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ[3DP RNS] Worker V1.1 (3D Printed Robot)<ul><li>Modify torso joints</li></ul>ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ[3DP RNS] Worker V1.0 (3D Printed Robot)<ul><li>Series : 2 Legs / Humanoid Type [<a target="_blank" href="https://youtube.com/shorts/tvGhQDAssUE?feature=share" rel="nofollow noopener">Youtube Video</a>]</li><li>This Is an all at once print. Assembly not required :)</li><li>If you subscribe to the YouTube channel [<a target="_blank" href="https://bit.ly/2KC3Tdx" rel="nofollow noopener">3DP RNS</a>], ★ a new robot will be revealed.</li><li>Thank you for your subscribing! It means a lot to me :)</li><li>Commercial License [<a target="_blank" href="https://www.patreon.com/3DPRNS" rel="nofollow noopener">Patreon</a>]</li></ul>&nbsp;※ Notice For my uploaded robot model to enable all joints to move, it&#39;s advisable to use a Brim.  If removing Brim is inconvenient or challenging, I don&#39;t recommend printing it.  Also, joint functionality may vary depending on the printer and filament you use. I hope your print is successful and you can have a robot with well-functioning joints.<figure class="media"><oembed url="https://www.youtube.com/shorts/tvGhQDAssUE"></oembed></figure>ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ[3DP RNS] Worker V2.0 (3D Printed Robot)<ul><li><a target="_blank" href="https://www.patreon.com/posts/3dp-rns-worker-0-100476630?utm_medium=clipboard_copy&amp;utm_source=copyLink&amp;utm_campaign=postshare_creator&amp;utm_content=join_link" rel="nofollow noopener">[3DP RNS] Worker V2.0 Download [Patreon]</a></li><li>Worker V2.0 can be obtained through Patreon (Hero) membership.</li><li>There have been some changes to the joints and additional design details have been added.</li></ul><figure class="media"><oembed url="https://www.youtube.com/shorts/rWWGnp2Mcy4"></oembed></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000117513/design/2024-03-17_3ca93d4eaa5cb.png"></figure>ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ[3DP RNS] Astro V1.0 (3D Printed Robot)<ul><li><a target="_blank" href="https://www.patreon.com/posts/3dp-rns-astro-v1-102720556?utm_medium=clipboard_copy&amp;utm_source=copyLink&amp;utm_campaign=postshare_creator&amp;utm_content=join_link" rel="nofollow noopener">[3DP RNS] Astro V1.0 Download [Patreon]</a></li><li>Astro V1.0 can be obtained through Patreon (Hero) membership.</li><li>If the existing humanoid robot, Worker, had a design of straight lines, this robot has been designed with curves.</li></ul><figure class="media"><oembed url="https://www.youtube.com/shorts/ThhzUq1ta_Q"></oembed></figure>