pdavey751

skadis

waltersworld3d

<a target="_blank" href="https://www.patreon.com/waltersworld" rel="nofollow noopener">https://www.patreon.com/waltersworld</a>&nbsp;Be sure to check out our Patreon for all newly released models, monthly giveaways, and the opportunity to have models designed custom for you&nbsp;We are Venom!&nbsp;L3GO inspired, stands approximately 8 inches tall and is fully articulating! Two versions of the chest are included, as some had trouble removing supports when printing vertically. The split horizontal chest does require glue or some other bonding agent to reassmble. I tried using the built in pegs and dowel rods, but it never aligned perfectly, so I opted to do without. It&#39;s a small enough piece that it shouldn&#39;t require it. I use DAP Rapid Fuse from the Home Depot, it has a long enough working time to allow for readjustments after gluing.&nbsp;When gluing, glue only on the inner edge! Otherwise you&#39;ll have squeeze out and the glue will stain the model. I recommend some small spring clamps also to keep it in place once glued until dry. The seam is nearly invisible after putting the arms and head on.&nbsp;Be sure to check out our other L3GO inspired Marvel models! More are being added weekly!

Bricks Venom

lego bricks

luckyluc.64

New Smooth AMS Gen2 for Hydra Mod.Thanks to @firemanjc, we developed the Hydra version of my Gen2 Smooth AMS. He did an outstanding job providing the information I needed to design it properly. Hydra mod is an extreme design with an undesirable, steep feeding angle.Here is my solution. A variation of my popular Smooth AMS Gen2.&nbsp;This is designed For the Hydra Mod. But it would work fine in an unmodified AMS.📢 Issue Addressed:<ol><li>Smooth the jumping of the near-empty spool.</li><li>Reduce the AMS forces required to feed the filaments.</li><li>The PTFE tube acts like a fishing line to keep a smooth and even feeding.</li><li>Reduces friction.</li><li>Prevent the filament from eating the AMS feeding funnel or anything.</li></ol>&nbsp;Yep, it's not the only one out there.📢 What is distinctive about it;<ul><li>NO ROOM IS TAKING FROM THE SPOOL.</li><li>More compact but still as strung. (4.25g per unit and print 50% faster).</li><li>It can be printed in PLA, but I strongly recommend using minimum ABS, PETg, or better.</li><li>Yes, you can use any monster desiccant box.</li></ul>&nbsp;I highly recommend my Slim Desiccant box. You don't need to remove the spool when refreshing it.<a target="_blank" href="https://makerworld.com/en/models/69484#profileId-73827" rel="nofollow noopener">https://makerworld.com/en/models/69484#profileId-73827</a>&nbsp;You can find my Smooth AMS Gen2 for the X1 / P1 series.<a target="_blank" href="https://makerworld.com/en/models/128483#profileId-139112" rel="nofollow noopener">https://makerworld.com/en/models/128483#profileId-139112</a>&nbsp;Have fun in the MOD adventure.

Smooth AMS Gen2 for Hydra Mod

Bambu

prchlikblaine

Colorized Poker Chips Set: &nbsp;<ul><li>30 Chips per print </li><li>3hr 30m print time per 30 chips WITH filament changes</li><li>Only 11 filament changes per 30 chips</li><li>Recommended colors provided in print profile file</li><li>$1 to $500 denominations available </li></ul>&nbsp;Print Settings: &nbsp;<ul><li>0.28mm Layer Height</li><li>10% Gyroid or preferred infill</li><li>2 walls </li></ul>

Colorized Poker Set Chip - $1 to $500 Chips

poker

neocrisis

<div><h1>Summary</h1><div>I own 2 X-Workhorse Workbench from Husky. They already have holes in them but they are not the correct size to use with my bench dogs.I made an adapter which allows you to use 3/4in bench dogs.I got mine from Home Depot but it does not appear to be sold by them anymore. </div></div>

Bench Dog Adapter (Husky's X-Workhorse Workbench)

bench dogs

ME STUDIO

<h3>🌹🌹🌹 Introducing the 3D Printed Valentine Rose with Stem: "I Love You"! 🌹🌹🌹</h3>Express your love in a unique and heartfelt way with our enchanting 3D printed Valentine Rose. This one-of-a-kind gift combines the beauty of a rose with a personalized touch. Let's delve into the features of this romantic creation.&nbsp;&nbsp;***&nbsp;Copyright:All my designs are protected by copyright. By downloading, you agree to use the files for personal purposes only. This means that you do NOT have the right to sell 3D prints of the digital files, including selling products made from molds.If you want to sell my prints commercially and legally, you can join my Patreon:<a target="_blank" href="https://www.patreon.com/MESTUDIO" rel="nofollow noopener">https://www.patreon.com/MESTUDIO</a>&nbsp;The digital files (STL and other formats) may never be resold, shared, remixed or given away. Happy printing!&nbsp;***&nbsp;&nbsp;&nbsp;LOVE THIS DESIGN?&nbsp;You might also like my others:&nbsp;<h4>🎉 Adult Version: <a target="_blank" href="https://makerworld.com/en/models/90795#profileId-97152" rel="nofollow noopener">Link</a></h4><h4>🎉 Kids Version: <a target="_blank" href="https://makerworld.com/en/models/99723#profileId-106322" rel="nofollow noopener">Link</a></h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/514459/2024-01-06_2cd213434cbfe.jpg"></figure>2024 Happy New Year Party Glasses (Contains glasses frame, temples, Happy New Year style's lens and texts) :<a target="_blank" href="https://makerworld.com/en/models/90795#profileId-97152" rel="nofollow noopener">https://makerworld.com/en/models/90795#profileId-97152</a>&nbsp;&nbsp;<h4>🌈🦄 Magical Unicorn Calendar : <a target="_blank" href="https://makerworld.com/en/models/110396#profileId-118002" rel="nofollow noopener">LINK</a></h4><h4>🌈 🦖 Magical Dinosaur Calendar : <a target="_blank" href="https://makerworld.com/en/models/114991#profileId-123662" rel="nofollow noopener">LINK</a></h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/514459/2024-01-06_4a92f15c6d488.jpg"></figure>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

Valentine Rose with Stem "I love you"

Valentines

dfreshkremer

Snowman “coal” and realistic carrot nose. You will have to glue the spikes to the coal and carrot nose. Use the coal for the eyes and buttons down the front of the snowman. I have the z-seam set to random, which gives the carrot a nice texture. If you'd like the best quality on the coal, it is best to download the raw files and use adaptive layer height (smaller layer height towards the top), however for something like this, it's not completely necessary. PLA would probably be fine for these since it'll be used in the winter, however, I have also added a PETG print profile. If you print this and use it for a snowman, please post a “make” so I can see how it looks! Thanks!

Snowman Accessories

snowman

Nanodesigner

La HONEYCOMBO-X, una parete modulare pensata per laboratori o piccole officine. Potete considerarla come un remix del progetto originale disponibile online, credo su Printables.com con il nome utente @RostaP, che ringrazio per l'ispirazione. È importante precisare che queste versioni non sono compatibili tra loro. In comune hanno solo le celle a forma esagonale. Ho riprogettato completamente ogni aspetto, dalle dimensioni della griglia agli attacchi e agli accessori.Il progetto è composto da 61 parti suddivise in:- 6 griglie- 7 cornici- 16 accessori singoli- 10 Organizer accessori- 3 Dispenser- 1 Applique LED regolabile- 2 Sistemi di fissaggio a parete- 2 Sistemi di fissaggio accessoriTroverete una guida tecnica PDF dettagliata di 38 pagine in inglese e italiano. Prima di iniziare o per chi è semplicemente curioso, vi consiglio di leggerla, prestando particolare attenzione al messaggio iniziale. Ho anche realizzato un video esplicativo (in italiano) sul mio canale YouTube a questo <a target="_blank" href="https://youtu.be/I-A-65vCpI4" rel="nofollow noopener">link</a>, che può aiutare nella realizzazione del progetto insieme alla guida in formato PDF.Tutte le informazioni necessarie sono riportate nelle guide. Vi lascio con alcune illustrazioni e foto. Ringrazio "ERYONE" per il supporto fornito attraverso la fornitura dei filamenti. Auguro a tutti un'esperienza gratificante nella realizzazione di questo progetto. Se desiderate altri contenuti simili o se il progetto vi ha interessato, supportatemi con un like sul mio nascente canale YouTube e su altre piattaforme dove pubblicherò il progetto. In alternativa, se desiderate darmi un piccolo sostegno economico per il tempo impiegato, potete farlo attraverso il mio link PayPal: "<a target="_blank" href="https://paypal.me/RAIAGENNARO" rel="nofollow noopener">https://paypal.me/RAIAGENNARO</a>". Grazie a tutti&nbsp;-------------------------------------------------------------------- ENGLISH --------------------------------------------------------------------------------------------------&nbsp;the HONEYCOMBO-X, a modular wall designed for workshops or small workshops. You can consider it as a remix of the original project available online, I believe on Printables.com with the username @RostaP, whom I thank for the inspiration. It's important to clarify that these versions are not compatible with each other. They only share the hexagonal-shaped cells in common. I completely redesigned every aspect, from the grid dimensions to the attachments and accessories.The project consists of 61 parts divided into:- 6 grids- 7 frames- 16 individual accessories- 10 Accessory organizers- 3 Dispensers- 1 Adjustable LED wall light- 2 Wall mounting systems- 2 Accessory mounting systemsYou will find a detailed 38-page PDF technical guide in English and Italian. Before starting or for those who are simply curious, I recommend you read it, paying particular attention to the initial message. I have also created an explanatory video (in Italian) on my YouTube channel at this <a target="_blank" href="https://youtu.be/I-A-65vCpI4" rel="nofollow noopener">link</a>, which can help in the realization of the project together with the guide in PDF format.All the necessary information is provided in the guides. I leave you with some illustrations and photos. I thank "ERYONE" for the support provided through filament supply. I wish everyone a rewarding experience in completing this project. If you desire more similar content or if the project has intrigued you, support me with a like on my emerging YouTube channel and on other platforms where I will post the project. Alternatively, if you wish to provide a small financial support for the time spent, you can do so through my PayPal link: "<a target="_blank" href="https://paypal.me/RAIAGENNARO" rel="nofollow noopener">https://paypal.me/RAIAGENNARO</a>". Thank you all.

Honeycombo-X by NANODESIGNER

Italian Hex wall

M. Owize

<h2>Support for Amazon Echo Dot Alexa</h2>Echo Dot 4Echo Dot 4 with clockEcho Dot 5Echo Dot 5 with clock&nbsp;Echo Dot Width: 100mmEcho Dot Height: 89mm&nbsp;I was missing a fun stand for my Echo Dot. I modified the 3D mascot Phil aka Phil a ment to the size of the echo dot.10-15% Infill Gyroid.Use brim on the body. I used a 20mm outer edge to make sure it didn't fall off. Enjoy!

Amazon Echo Dot Alexa Dock

echo

Procs Design

This is a decorative foldable gift box which you can use to gift small presents, decorate your desk, put under a tiny Christmas tree, store candies, and whatever you can think of. This design features a box base and a lid that fit together. I designed it so that it requires no glue, tape or screws; minimal purge waste to print; different designs to choose from; and two sizes, the smaller one being able to fit on an A1 mini. It uses a single layer thin living plastic hinges and tabs that allow you to fold and snap it together to a sturdy box (as sturdy as a thin layer of plastic that is) and is surprisingly strong! Since it prints flat and folds up, the designs can come from Hueforge and only requires multicolor filament changes at layers which significantly reduces purge waste! This also means that an AMS is not required but is helpful. Unfortunately, the sizes are a bit small as you can only fit so much of a foldable design on the print bed.&nbsp;Sizes (interior volume):<ul><li>Normal (Printable on X1C, P1S, P1P, A1): 7.5cm x 7.5cm x 7.5cm (2.95 in x 2.95 in x 2.95 in)</li><li>Small (Printable on X1C, P1S, P1P, A1, A1mini): 5cm x 5 cm x 5cm (1.96 in x 1.96 in x 1.96 in)</li></ul>&nbsp;Print instructions:<ul><li>Designs are separated by profiles, each pattern has two versions. One for the X1, P1, A1 printers, and one for the A1mini. The A1mini can only fit the small size while the X1, P1, A1 versions have both sizes! Read the description carefully and select the correct design you want. Make also sure to select the correct plates of the size you are interested in.</li><li>If you have an AMS, use only the AMS plates in the profiles! If you don't have an AMS, use the pause swap plates. When using the pause swap plates, it will pause at the color changes. Simply unload and load a new color filament and resume the print. The profile description has a description of the order of colors so make sure to read them.</li><li>All you need to do is decide on a pattern to print, then select my appropriate profile. Afterwards choose what plate you want to print, each plate will have a different part, size, and AMS requirement. Do not increase the number of copies as it will auto rotate the models which may cause the living hinges to fail.</li><li>Tolerances are tight for this model due to the living hinges. Please make sure that your printer can handle a 0.15mm gap. Otherwise it may be a bit difficult to bend the hinges or it may fuse together.</li><li>Make sure that your first layer bed adhesion is good, the living hinges are on the first layer and any first layer defect may affect the bend-ability.</li><li>Check back every now and then, I will be updating this box with more designs as I test and print them!</li></ul>&nbsp;Assembly InstructionsWhen removing your print from the print bed, please be gentle and slow. The living hinges are thin and can be torn off if you aggressively remove the print. If using a textured or hot plate, please wait for the plate to cool completely first before removal. If using a plate with high adhesion where you need to peel or pry it off because bending the plate doesn’t work, consider using a medium for easy release like a glue stick or hair spray. Please see documentation for bigger versions of these pictures.&nbsp;<figure class="image image_resized" style="width:50.36%;"><img src="https://makerworld.bblmw.com/makerworld/draft/531581/2023-12-31_c5d5f24f17c788.png"></figure><figure class="image image_resized" style="width:49.97%;"><img src="https://makerworld.bblmw.com/makerworld/draft/531581/2024-01-15_afe3359d3d038.png"></figure>&nbsp;Designs:Spiral Pattern: Two colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White (background, can be any color you want)</li><li>PLA Sunlu Red (Spiral stripes, can be any color you want)</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Snowflake Pattern: Two colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White (background, can be any color you want)</li><li>PLA Sunlu Black (Snowflakes, can be any color you want)</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Maze: Two colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White (background, can be any color you want)</li><li>PLA Sunlu Blue (Maze walls, can be any color you want)</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Poinsettia Pattern: Three colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White</li><li>PLA Sunlu Red (Petals)</li><li>PLA Sunlu Grass green or Green (Leaves)</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Ornaments: 3 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Grass Green (Ornament color, any base color should work like red or blue)</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Snowy Trees: 4 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Grass Green</li><li>PLA Overture Matte Light Blue</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Watercolor Snowflake: 4 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Blue</li><li>PLA Overture Matte Light Blue</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Starry Night: 4 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Blue</li><li>PLA Sunlu White</li><li>PLA Overture Matte Yellow</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Blue Marble: 3 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Blue (or any base color you want your marble to be)</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;&nbsp;Great Wave: 3 colors, hueforge printPrint at 100% infill with a layer height of 0.1mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu Black</li><li>PLA Sunlu Blue</li><li>PLA Sunlu White</li></ul>&nbsp;Swap Instructions:See my print profile description for swap instructions if you don't have an AMS. I have included print profiles with plates that have pauses included for your manual swapping needs, make sure to choose the right one!&nbsp;Hearts Pattern: Three colors, simple and fast printPrint at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmFilaments Used:<ul><li>PLA Sunlu White </li><li>PLA Sunlu Red (lower hearts)</li><li>PLA Sunlu Sakura Pink (upper hearts)</li></ul>&nbsp;Swap Instructions:<ul><li>Start with White </li><li>At layer #5 (1.0mm) swap to Red or Pink (lower hearts)</li><li>At layer #8 (1.6mm) swap to Pink or Red (upper hearts)</li></ul>&nbsp;Basic Box and Basic SLIM Box: The basic box, no design on the walls for easy remixing or customizing.Print at 100% infill with a layer height of 0.2mm with a base layer of 0.2mmAny color you want.Note the model differences:<ul><li>Basic Box has a wall thickness of the base at 2mm as all lids are designed to fit on a box that size.</li><li>Basic SLIM box has a lip of 2mm for the lid and the rest of the walls are 1mm for your remixing or sticker needs, choose that one if you want to add some depth to your box.</li><li>All lids are 1mm thick in this set, as nothing requires them to be thicker.</li><li>Keep in mind how it bends when adding details to the 3d model.</li></ul>&nbsp;&nbsp;Want to slice these files yourself?While I recommend you use the profiles I have prepared and tested, you can slice it yourself if you follow these recommendations:<ul><li>For all projects, make sure to print at 100% infill, it is thin enough that having sparse infill can cause surface defects with a minor reduction in filament used which is not worth it.</li><li>For all projects, the first layer must be 0.2mm thick, the living hinges are designed based on that thickness.</li><li>For any boxes that include Hueforge designs, please print layer height of 0.1mm with a base layer of 0.2mm.</li><li>Do not rotate the files or change the first layer infill pattern, the infill pattern must be 45 degrees to the walls of the model to allow the thin living hinge design to work well.</li><li>I do not recommend scaling the model, it has tight tolerances on the living hinge and Hueforge designs are optimized at a specific scale.</li></ul>&nbsp;Update Log2023/11/23 Release with 4 designs: Spiral pattern, Watercolor snowflake, Ornaments, Snowy trees2023/11/27 Update with 4 new designs: Snowflake pattern, Maze, Poinsettia pattern, Starry Night2023/12/03 Update with 1 new design and opened remixes: Basic Box + SLIM2023/12/31 Update with 2 new designs: Great Wave and Blue Marble2024/2/11 Update with 1 new design: Hearts Pattern