onefast50

SavageLau

<h4><i><strong>If you want commercial license, check out my bio and get it from Patreon. </strong></i></h4><p>&nbsp;</p><p><strong>         This is full verison of the pistion trophy design. Full size , Bore dia 98mm. There are major feature changes from the semi-assembled one. The piston rod position have <u>15 degree to 30 degree max angle adjustbility</u> from vertical center line. Pistion have 60degrees adjustbility from horizontal surface.  All the connection part will have <u>tight fit</u> by design so you could keep it in position after adjustment. </strong></p><p><strong>        The dripping overhang issue is also taken consider during design process, by the orientation that I put on print file, these amount of overhang will work as friction component to keep the over all fitting tolerancing. At the same time those ugly overhang is not visiable to you after assembled. So, good deal. To proof there is attention to detail on my work, lol. (If your filament have huge sinkage rate, it might cause issue.)</strong></p><figure class="image image_resized" style="width:65.32%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_e5bd5df29d4f6.png"></figure><p><strong>        There is <u>no other hardware required</u>. All parts are printable, but you will need to assembly it yourself.</strong></p><p><strong>         I made different print files for different color setting. Introduction is below. It would be a great little build project with kids. </strong></p><p><strong>Tag is interchangeable.</strong></p><p><strong>        Have fun!</strong></p><figure class="image image_resized" style="width:57.57%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_ab82d19a1b408.png"></figure><p>&nbsp;</p><p>&nbsp;</p><h2>All the parts:</h2><figure class="image image_resized" style="width:56.87%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_0a4ce2dc60992.jpg"></figure><p>&nbsp;</p><h2>Assembly instruction:</h2><p>Due to the different material sinkage rate are different, I have tested many different revision of bolts sizes, but most of them end up hard to assembly, or break eaily for silk filament . At the end, I have decided to change the bolt to pin. All the pins are designed to be tight fit. You may need to hammer it down a little bit.</p><figure class="image image_resized" style="width:50.45%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_0bcb4348d6cbd.jpg"></figure><p>&nbsp;</p><h2>Step 1: crankshaft holder assembly.</h2><figure class="image image_resized" style="width:59.14%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_42168ca2dcbcc.jpg"></figure><p>&nbsp;</p><h2>Step 2: Coupler for connecting rod. Hammer in the pin on rod side first, then put coupler in.</h2><figure class="image image_resized" style="width:59.11%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_e27c5ea3d7178.jpg"></figure><figure class="image image_resized" style="width:59.34%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_e56108cd22cfa.jpg"></figure><p>&nbsp;</p><h2>Step 3: Install piston rings. Make sure the cut are not alined, lol, you don't have to. Car guy, you know why.</h2><figure class="image image_resized" style="width:58.42%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_037b5bbfbd0b8.jpg"></figure><figure class="image image_resized" style="width:57.96%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_7572472ce25ab.jpg"></figure><p>&nbsp;</p><h2>Step 4: Connecting rod with piston.</h2><figure class="image image_resized" style="width:59.63%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_910984c9cae3e.jpg"></figure><p>&nbsp;</p><h2>Step 5: Put piston assembly on crankshaft rod. And, you done.</h2><figure class="image image_resized" style="width:58.47%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_e26dd0a8e9429.jpg"></figure><p>&nbsp;</p><p>&nbsp;</p><h2>Some print file different:</h2><h2>Option one: Ultimate color version. More plate, so you have switch different color of filaments that you want.</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_de716304d4543.png"></figure><h2>Option two: Less plates.</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_0c278597f77bf.png"></figure><h2>For a1mini folks:</h2><figure class="image image_resized" style="width:85.55%;"><img src="https://makerworld.bblmw.com/makerworld/draft/399843/2023-12-18_084d4a47c573.png"></figure>

Piston Trophy (real size/full printed)

trophy

Plastic Avatar

A1 mini AMS lite Overhead Mount | v1

A1 Mini

jirawin.arty

<p><span style="background-color:rgb(28,30,33);color:rgb(224,224,224);font-size:16px;">Linear rails for Y axis</span></p>

Linear Rails for ender 6

Ender 6

Ender 6 skirt test