onebigbrew

Yedoggie

This is my V6 engine block cooler. Perfect for backyard get-togethers. The engine block is sliced into 4 sections so that it can fit on the P1 and X1 printer. There is also a drain plug (I used TPU to make). Holds six drinks, can or bottle. The tolerances are tight and will require you to seal the seams unless you do not mind melting ice to run out from the bottom or sides.&nbsp;Note:PETG for engineTPU for drain plugSupport required&nbsp;My V8 Version: <a target="_blank" href="https://makerworld.com/en/models/236157#profileId-252311" rel="nofollow noopener">https://makerworld.com/en/models/236157#profileId-252311</a>Koozie: <a target="_blank" href="https://makerworld.com/en/models/411911#profileId-313818" rel="nofollow noopener">https://makerworld.com/en/models/411911#profileId-313818</a>&nbsp;&nbsp;

V6 Engine block cooler

misc

RPM Designs LLC.

This is a Rotating Lithophane box that I created for my family memories. The box spins at .5 rpm so its slow enough to watch and take in the images&nbsp;Print at .2 or finer layer height. I love the bronze color- star wars inserts for reference only. Even tried to color one with packing tape on the back of it and sharpies came out cool. Saw this on a facebook post.&nbsp;I use <a target="_blank" href="https://lithophanemaker.com/Framed%20Lithophane.html" rel="nofollow noopener">https://lithophanemaker.com/Framed%20Lithophane.html</a> to make the lithopahnes.&nbsp;The size of the lithophane is 149mm tall by 111mm wide. I put a 3mm border around it to snug it up a little but slides right in and then is capped with the bottom plate for the cage.&nbsp;You need to wire the switch lights and motor to work with the switch.From the power port red wire will go to the light red and motor positive. The black groud wire will go to onde side of the switch then out the other side of hte switch to the light ground and motor ground. Pretty simple wire circut for the switch to work. I have added an alternative power port in the links below as well which gives it a little cleaner look and no need to glue the port it has a nut on it.&nbsp;The parts and filament I usedLights  <a target="_blank" href="https://amzn.to/3UrwpCn" rel="nofollow noopener">https://amzn.to/3UrwpCn</a>&nbsp;Filament <a target="_blank" href="https://amzn.to/3U4cutf" rel="nofollow noopener">https://amzn.to/3U4cutf</a>&nbsp;Power Supply. <a target="_blank" href="https://amzn.to/47FD2UF" rel="nofollow noopener">https://amzn.to/47FD2UF</a>&nbsp;Motor. <a target="_blank" href="https://amzn.to/3vGnl2i" rel="nofollow noopener">https://amzn.to/3vGnl2i</a>&nbsp;Switch. <a target="_blank" href="https://amzn.to/3OfsPaD" rel="nofollow noopener">https://amzn.to/3OfsPaD</a>&nbsp;Wire <a target="_blank" href="https://amzn.to/3Oc62MP" rel="nofollow noopener">https://amzn.to/3Oc62MP</a>&nbsp;Screws. <a target="_blank" href="https://amzn.to/490stN7" rel="nofollow noopener">https://amzn.to/490stN7</a>&nbsp;Heat Shrink <a target="_blank" href="https://amzn.to/3Hq253h3" rel="nofollow noopener">https://amzn.to/3Hq253h3</a>&nbsp;Soldering Iron <a target="_blank" href="https://amzn.to/4aYGxbT" rel="nofollow noopener">https://amzn.to/4aYGxbT</a>&nbsp;Alt Power Port. <a target="_blank" href="https://amzn.to/4b3xWEy" rel="nofollow noopener">https://amzn.to/4b3xWEy</a>&nbsp;ThanksKeith&nbsp;