omgitsmelvino

The Philosopher

Picture this: you&#39;re home by yourself, sitting on your porcelain throne, and you are ready to depart from your bathroom when you instinctively reach to the side. You reach for it again, but to your dismay, nothing is there, and you slowly look over. Could it be? Could you really have ran out of toilet paper? Now what??? Teepee ensures that this will never happen again. with a modular stacking system, the only limit to how many rolls you can store is your ceiling height. You can use teepee in two configurations, with a receptacle at the bottom that will hold the roll, or with a dispenser and rods for each roll that allows you to use it as a regular toilet paper holder which can “eject” the roll automatically when it is empty, allowing the next full one to automatically roll into the dispenser.&nbsp;This system should work with 99% of toilet paper rolls, however I have included the f3d file just in case, so the size can be increased. You could also just scale the model up, which should work just as well.&nbsp;&nbsp;Printing &amp; Assembly:&nbsp;Printing requires a very small amount of supports for the bottom of each straight piece, as well as supports for the curved portion if you choose to not split it.&nbsp;As for assembly, any strong glue should suffice, or as an alternative you could spot weld the pieces together. To attach the entire thing to your wall, I would recommend either tape or some sort of adhesive, to prevent making a hole in your wall.&nbsp;I have also included a test print, as this entire project is filament intensive, it is a good idea to make sure that each piece will fit together properly before printing the whole thing.  Notes:&nbsp;The dispenser with the ejection system is still quite hairy, and depends on the toilet paper roll. I am working on a more consistent version, but for now I would suggest printing both the receptacle and the dispenser to see which one works better for you. As always, feel free to modify the model as you need, I can provide any other files.&nbsp;To use the ejection system, you must print a rod for each roll you wish to use at any given time, and slide them into the holder. This ensures that each new roll is able to spin freely in the dispenser.&nbsp;Want More? Check out my modular dispensers! https://makerworld.com/en/models/412523

Teepee: Modular Bathroom Crisis Prevention System

Bathroom Shit

Teixi3D

I bring you a painted style Super Mario model, created with HueForge. I hope you like it!!&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: PLA PolyTerra Charcoal Black Transmission Distance: 0.3 PLA PolyTerra Pastel Watermelon Transmission Distance: 1.5 PLA PolyLite Pro Light Blue Transmission Distance: 1 PLA Protopasta White Transmission Distance: 3Swap Instructions: Start with Charcoal Black At layer #7 (0.64mm) swap to Pastel Watermelon At layer #15 (1.28mm) swap to Light Blue At layer #22 (1.84mm) swap to White for the rest.

super mario painting (HueForge)

Hueforge

everydaynormalguy99

I made this keychain from an svg file from the internet, printed in two colors on a P1S with AMS, it has three color changes Print in PLA

Jesus Keychain

keychains

hectorri

A 20mm size cube to basic print test. I made a display stand to all layer heights variants: <a target="_blank" href="https://makerworld.com/en/models/48746" rel="nofollow noopener">https://makerworld.com/en/models/48746</a> <img src="https://makerworld.bblmw.com/makerworld/draft/116605/2023-10-24_986a5722bc89.jpg">

Calibration cube XYZ

tools

Comi

<blockquote>You can use boring paper bookmarks or you can go with this one, that is outstanding!</blockquote>The print itself is very easy, use my profile, that is tested well. The print takes only 2 grams of filament and under 12 minutes of print time.Sharing is carrying, so please dont forget to post your makes when rating the print profile and share with others :-)<h3>Printing</h3><ul><li>Use my tuned print profile. You can add as many mookmarks as you want to the print plate. Default number is 1 bookmark.</li></ul>Happy printing and reading!

Starship Bookmark

Bookmarks

Tommy Gun

Here&#39;s a nice set of 5 coasters and amazing question mark block coaster holder/box !!&nbsp;Easy print, only have the ? and dots inserts to glue on as i wanted to save on filament !!!&nbsp;Coasters Dimensions: 104 mm diameter 4 mm height&nbsp;-Print x4 question mark inserts and x16 Dots inserts&nbsp;Interested in selling my prints : <a target="_blank" href="https://patreon.com/Papa3dHomemadePrints" rel="nofollow noopener">https://patreon.com/Papa3dHomemadePrints</a> &nbsp;Brother Box <a target="_blank" href="https://makerworld.com/en/models/112575#profileId-120555" rel="nofollow noopener">https://makerworld.com/en/models/112575#profileId-120555</a> &amp; Super mario Pipe holder : <a target="_blank" href="https://makerworld.com/en/models/101819#profileId-108453" rel="nofollow noopener">https://makerworld.com/en/models/101819#profileId-108453</a>&nbsp;Pen box&amp;pipe holder : <a target="_blank" href="https://makerworld.com/en/models/141100#profileId-153752" rel="nofollow noopener">https://makerworld.com/en/models/141100#profileId-153752</a> &nbsp;Question mark lightbox : <a target="_blank" href="https://makerworld.com/en/models/127720#profileId-138211" rel="nofollow noopener">https://makerworld.com/en/models/127720#profileId-138211</a>&nbsp;Grey Brick coaster box and coasters : <a target="_blank" href="https://makerworld.com/en/models/210143#profileId-230023" rel="nofollow noopener">https://makerworld.com/en/models/210143#profileId-230023</a>

Super Mario ? Coaster Box and Coaster set x5

cool stuff

braga3dprint

Introducing the Luigi Light Box: A captivating tribute to the iconic Luigi from the world of Super Mario. This 3D model embodies the adventurous spirit of the taller, green-clad Mario brother, capturing Luigi in his signature pose, ready for action. Every detail, from his distinctive cap to that friendly mustache, is meticulously crafted. When illuminated, the lightbox truly brings Luigi to life, making it a must-have for gaming enthusiasts. Let this warm, nostalgic glow evoke the magic of countless adventures with Luigi in the Super Mario universe. 🌟🍄&nbsp;If you don't have or don't want to install LED's you can just glue the parts together and have an awesome sign! WARNING!- remove purge line at the beginning of the print!&nbsp;Materials and tools: - glue gun - aluminum tape - led strip (here is the one I <a target="_blank" href="https://pt.aliexpress.com/item/1005004253095880.html?spm=a2g0o.order_list.order_list_main.16.1df1caa45b098E&gatewayAdapt=glo2bra" rel="nofollow noopener">use</a>): simple 1m white led USB- soldering iron (optional)&nbsp;RECOMMENDATIONS- use a textured PEI sheet - use the print profile, it has quite a few setting changes that help achieve the best results - make a hole for the USB strip wherever you like it best with a soldering iron, drill or in the slicer- use the aluminum tape on the inside of the backplate to help with light diffusion - glue the LED's the further away from the colored design possible; placing them too close ruins the diffusion and the individual LED's become visible Bambu Studio Settings: I always recommend using the print profile I provided since it has settings with which I've been able to get the best results. If you choose not to here are the main slicer settings I recommend: - preferences (ctrl + P) → activate developer settings → Quality →Advanced → First Layer Flow Ratio: 1.04 - Quality → Wall generator → Arachne - Quality → Wall transitioning threshold angle → 50º - Strength → Advanced → Infill/wall overlap → 20% - Quality → Advanced → Avoid crossing walls - Increasing retraction / reducing temperature can help reducing wisps - Order color printing from lightest to darkest color How to make a hole in Bambu Studio:<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=OsA23WCxRtg"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/OsA23WCxRtg" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure> Assembly video: <figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=QNsShLmXYh0"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/QNsShLmXYh0" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;

Luigi Lightbox LED Lamp

Lightboxes

Picture_it

Cute stitch key chain. Print face down. Easily painted by object or in Bambu Studio

Stitch Keychain

Stitch 

sassiecat3d

Timme is a T-rex, and he's of a very special species called a Cutasaurus Rex, they are very rare and only lives where theres a 3d printer in site! They love to hangh out on the varm cozy printer and makes sure nobody messes with the prints!&nbsp;*****&nbsp;Important when downloading the design: This is my design and copyight to me sassiecat3d, it's not to be used commercially or resold without my permission, the stl file is under the same clause, not to be re-sold or use commercially without my permission. You are welcome to contact me if you would like to know more. :-) You agree to these terms when you download this file.&nbsp;*****&nbsp;For buying the commercial version where you can print and sell copys of a physical 3d printed version, go here: <a target="_blank" href="https://cults3d.com/en/3d-model/art/timmy-the-cutasaurus-rex-commercial-version" rel="nofollow noopener">https://cults3d.com/en/3d-model/art/timmy-the-cutasaurus-rex-commercial-version</a>