newcomb.austin

JamesThePrinter

A small, strong case with a collection of optional inserts for different uses.&nbsp;<h3>Case</h3>Use a section of 1.75mm filament inside the hinge to connect the lid to the base. Depending on your printer/setup, this hole maybe be on the tight side or a bit loose. If tight, drilling out the hole may help. If it is slightly oversized, I suggest melting the end of the filament piece with a soldering iron or lighter.This can be a standalone case or you can add inserts for more functionality. &nbsp;&nbsp;Print SettingsBase and Lid can be printed with 3 perimeters and 0% infill. Using these settings, most walls will be solid. &nbsp;<h3>Optional Inserts</h3><ul><li>Battery Holders <ul><li>AA Holder - fits up to 6 AA batteries</li><li>AAA Holder - holds up to 8 AAA batteries</li><li>9V Holder - fits up to 2 9V batteries</li></ul></li><li>Digital Storage Holders - Can be used together or separately<ul><li>MicroSD Card Holder - fits up to 12 MicroSD cards in the lower section</li><li>SD Card Holder - fits up to 6 SD cards in the upper section</li></ul></li><li>Dividers<ul><li>Full Divider - Splits the entire case into 2 compartments</li><li>Upper Divider - adds 2 compartments on top - Can be used with the Lower Divider</li><li>Lower Divider - adds 2 compartments on bottom - Can be used with the Upper Divider</li></ul></li><li>Nozzle Holders - Can be used together or separately <ul><li>Upper Nozzle Holder - fits 14 standard nozzles (MK8 or E3D V6)</li><li>Lower Nozzle Holder - fits 14 standard nozzles (MK8 or E3D V6)</li></ul></li></ul>Print SettingsNo special print settings are needed for any of the inserts. I used 3 perimeters and 10% infill. &nbsp;&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:Black Case<ul><li>polymaker PolyTerra Charcoal PLA</li><li>Hatchbox Sparkle Gray PLA</li></ul>Red Case<ul><li>polymaker PolyTerra Army Red PLA</li><li>polymaker PolyTerra Lava Red PLA</li></ul>Yellow Case<ul><li>PrintBed Yellow PLA</li><li>polymaker PolyTerra Banana PLA</li></ul>Teal Case<ul><li>polymaker PolyTerra Arctic Teal PLA</li><li>PrintBed Baja Blue PLA</li></ul>Purple Case<ul><li>Prusament Galaxy Purple PLA</li><li>Fillamentum Lilac PLA</li></ul>Orange Case<ul><li>CC3D Flame Orange PLA+</li><li>Inland Orange PLA</li></ul>Green Case<ul><li>PrintBed Green PLA</li><li>polymaker PolyTerra Forest Green PLA</li></ul>Blue Case<ul><li>GIANTARM Matte Navy Blue PLA</li><li>polymaker PolyTerra Sapphire Blue PLA</li></ul>

Multi-Use Case with Inserts

Useful

kylemraley

<a target="_blank" href="https://makerworld.com/en/models/78647#profileId-82948" rel="nofollow noopener">- Darth Vader Available Here -</a> Full Size Stormtrooper Helmet - Pre colored w/ Bambu Studio & AMS.Multiple plates, and multiple pieces. Glued together. Sorry - no instructions included with original, easiest way for me was to use a reference photo.

Stormtrooper Helmet - Colored

ambitious 

linton

I made a supportless citadel paint holder to transfer into 15ml dropper bottles using included funnel in the common kits you can buy. Compatible bottles pictured for reference including dimensions.&nbsp;Fairly easy to use, insert empty bottle, funnel and open citadel paint pot upside down and then flip it over and watch the magic. You can use flow improver, airbrush thinner or water to help first just mix a bit in.&nbsp;Have fun!

Citadel paint pot to dropper bottle transferer

WHammer

A. Guy

Your friendly, neighborhood, poop dragon! Or, I guess it could be a Soft-serve Ice Cream Dragon, if you think the poop emoji is gross.

Useful

ambitious

WHammer

funny