nazrethh

fisherbrad922

A revised version of my bridge as part of my RC Crawler park. I made the wheel area of the steps and bridge wider, as it was a bit small for 1/24 scale cars. Enjoy!&nbsp;See full set- <a target="_blank" href="https://makerworld.com/en/models/205374#profileId-225548" rel="nofollow noopener">RC Crawler Park by fisherbrad922 - MakerWorld</a>

RC Crawler Park Bridge v2- Wider Wheel Area

rc. rawler

LordBoos

Night Dragon (Lithophane) - HueForge&nbsp;To celebrate 200 downloads of my <a target="_blank" href="https://makerworld.com/en/models/16099#profileId-15125" rel="nofollow noopener">Night Dragon (Filament Painting) - HueForge</a> model, I recreated this model as a special edition in a form of Lithophane. It still looks good without backlight, but it really pops out when you backlight it!<h4>Printing instructions:</h4>Warning! This model requires very translucent filaments to be used as blue and purple colors and also a mildly translucent white. I used glitter PLA filaments from eSUN and AzureFilm, they are almost like a natural PLA only lightly tinted blue and purple with added glitter. Glitter is not that important, but it still adds a little something to the print. If you use very opaque filaments, it might not allow enough light to pass through and the lithophane might become very dark or not translucent at all. You can still attempt it, but you have been warned.&nbsp;Filament swaps ONLY, no MMU or AMS required, but AMS makes it much easier.Use Original HueForge profile to get the intended look, my models are very sensitive to print settings because of color blending between layers. Every setting and filament changes for AMS are carefully prepared and fine-tuned in the Original HueForge print profile, feel free to change colors, but I recommend not to adjust other settings. If you want to experiment with your own settings or non-original print profiles, for best look print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm.You can use same filaments as I did, or you can experiment with your own.Don't forget to upload a make!<h4>Filaments Used:</h4><ul><li>PLA BambuLab Basic Jade White Transmission Distance: 4</li><li>PLA AzureFilm Glitter Blue Transmission Distance: 7</li><li>PLA eSUN eTwinkling Purple Transmission Distance: 6</li><li>PLA BambuLab Basic Black Transmission Distance: 0.6</li></ul><h4>Swap Instructions:</h4><ul><li>Start with Jade White</li><li>At layer #5 (0.48mm) swap to Glitter Blue</li><li>At layer #12 (1.04mm) swap to eTwinkling Purple</li><li>At layer #19 (1.6mm) swap to Black for the rest.</li></ul>

Night Dragon (Lithophane) - HueForge

lithopane prints

Saber3D

Check all my models out at <a target="_blank" href="https://saber-3d.com/" rel="nofollow noopener">www.Saber-3D.com</a> &nbsp;New dragons, creatures, and more released every month to my patrons, thank you for supporting my work! &nbsp;Follow our socials to see new models! <a target="_blank" href="https://www.instagram.com/saber.3d" rel="nofollow noopener">Instagram</a><a target="_blank" href="https://www.tiktok.com/@saber3d" rel="nofollow noopener">TikTok</a>&nbsp;This flexi dragon was designed to take less time but still give you the awesome look of a large dragon as well as make custom designs as easy as possible! Every part of this dragon can be easily painted in your slicer of choice, just make sure edge detection is turned off 😉&nbsp;Want to sell prints or just enjoy the instant access to all my models? join our All Access tier on <a target="_blank" href="https://www.patreon.com/Saber3D" rel="nofollow noopener">Patreon</a>. &nbsp;&nbsp;&nbsp;&nbsp;&nbsp;