my.workshop.life

DKprints

A mini molle panel folding camp table! This magnetic table is great for attaching small camp items to your vehicle once at the campsite, or for taking notes on your fridge! It locks in the upward position and uses integrated end stops in the downward position. I use it to organize my charging cables and it makes for quick access to essential items once they&#39;re attached! When folded down, it makes a great horizontal surface for drinks or other things! Print in PETG or ASA for prolonged outdoor use. &nbsp;Requires some additional parts:(1) M4 x 160mm Threaded Rod - I used <a target="_blank" href="https://a.co/d/hmznyoX" rel="nofollow noopener">https://a.co/d/hmznyoX</a>(2) Strong Rubberized Magnet - I used <a target="_blank" href="https://a.co/d/b8xvIC8" rel="nofollow noopener">https://a.co/d/b8xvIC8</a>(4) M4 x 12mm Countersunk Screws <a target="_blank" href="https://a.co/d/fo2LEX6" rel="nofollow noopener">https://a.co/d/fo2LEX6</a>(6) M4 Nuts - Included in countersunk screw assortment (6) M4 Washers - Included in countersunk screw assortment &nbsp;It is way more cost effective to get a assorted hardware kit for the M4 screws, bolts, nuts, and washers instead of purchasing individually. A #8 or 5/32&#34; Hardware set and treaded rod will also work, however the diameter is slightly bigger than the M4 hardware and may require more torque to assemble. &nbsp;Tools Needed: - Needle-nose Pliers - 2.5MM Hex Key Allen Wrench&nbsp;Assembly Instructions: Step 1: Attach the magnets to the Molle Panel Case by pushing the M4 Countersunk screw through the magnet, then case itself. Make sure the rubberized part of the magnet is faced outward away from the case. Step 2: Use one M4 washer and nut on to fasten the magnet to the Molle Panel Case. Repeat for the other 3 screws. Step 3: Align the Molle Panel Plate into the Molle Panel Case making sure the print bed surface is faced outward and the hinges are faced inward. Step 4: Insert the threaded rod into the side cutout of the Molle Panel case and through both Molle Panel Parts until an equal length of threaded rod is poking out of each end. You may need to twist the last couple of turns with pliers taking care not to damage the end threads. Step 5: Lock the threaded rod in place with a washer and nut on each end of the threaded rod. Step 6: Make sure the Molle Panel locks in the upward position and sets on the small integrated endstops on the lower position.Step 7: You&#39;re Done!&nbsp;

Mini Folding Molle Panel Camp Table

Molle

rexor400

This is a fully printable resin vat draining rack with height-adjustable vat holder and funnel systems. To adjust, loosen the lock bolt, slide the funnel or holder to the desired height, and re-tighten the lock bolt. The rack grooves mate with half-cylinders inside the vat holder (see CAD cross-section photo) when the locking bolt is tightened down, so there is no sliding once the weight of the vat is present. The holder is angled forward by 5 degrees to prevent resin from dribbling under the corner of the vat. The angle also maximizes stability by moving the center of gravity forward. This is very stable even when adjusted to the maximum height! The funnel is a separate item from the "car" it rides in. The ring in which the funnel sits is open on the end to aid in putting it in/out when the funnel is raised up close to the vat. There is a template that allows you to slide standard paint filters inside it, to aid in cutting them down the right size/shape to fit the funnel - very handy!

Resin Funnel For Vat Cleaning

resin

deigge

I liked the "Modular Cress/Sprout Sieve/Farm" but I only wanted to print one of them. The problem was, it was not that easily accessible in my small greenhouse. Thats why I designed the non-modular stand for this modular farm :PIt was quickly thrown together, that's why I didn't design it in different parts that can be put together. Use the cut tool in the slicer to make two parts that can be printed without supports and then glue them together.

Modular Cress/Sprout Sieve/Farm Stand

Garten/Pflanzen

Martin_au

<div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=TK3BMPxdlYI"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/TK3BMPxdlYI" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe></div> </div> Design criteria:<ul><li>It had to be usable in the field or the lab.</li><li>Therefore, it had to be compact and easy to store and transport,</li><li>……and that includes the magnetic stirrer bar…..</li><li>And it would need to run on batteries,</li><li>As it also had to double as a lab stirrer, it also required power for long term use.</li><li>It had to stir volumes from 10 to 1000 ml.</li><li>It had to be feasible to fabricate.</li><li>It had to be resistant to spills and chemicals.</li></ul>Vitamins<ul><li>2x M3x5mm screws for the PWM controller</li><li>2-3x M2x8mm screws for the charge controller</li><li>2x M2x10 mm nuts and screws for the rotator</li><li>7x M3x8mm screws for the lid and the motor clamp</li><li>1x M3x8mm nut and screw for the motor clamp</li><li>7x M3 Brass inserts</li><li>5 x 10mmØ x 3mm thick magnets.</li></ul>Electronics:<ul><li>Pimoroni Amigo Pro USB-C charge controller</li><li>LiPo 3.7V 1100mAh</li><li>PWM controller</li><li>Motor - <a href="https://www.aliexpress.com/item/33047774688.html?" rel="nofollow">https://www.aliexpress.com/item/33047774688.html?</a></li></ul>If you want to buy me a coffee for the design, you can also purchase the files here: https://www.etsy.com/au/listing/1347129276&nbsp;

Magnetic Stirrer

Projekte 

CarpeYeti42

This is the airsoft version, I'll upload a reenactment version without the holes needed for the airsoft version.&nbsp;I took inspiration from Wether Industrie's system to build French Offensive grenades.Here's how to reload/assemble the fuse part : <figure class="media"></figure>&nbsp;The grenade and fuse assembly were printed in PLA+ and painted, the spoon and rivets are printed in silver silk pla.I recommend using 3 or 4 walls at most to keep the weight down and not risk hurting your target.I inserted a M3 cap head screw in the firing pin to improve reliability, the percussion cap nipple is a 4mm pop rivet reamed to 3mm to make room for the fuse. The spring is 9x20mm.The safety pin was bent using a homemade jig from 1.5mm piano wire.

Airsoft / Reenactment French OF 37 Grenade

Airsoft

Daniel Schenk

<div><h1>Summary</h1><div>Simple Gridfinity 5x5 box 6u heightUpdate: V2Base and V2Lid with more clearance around the alignment features and improved locking mechanismHardware: 8x M3x6 set screw to fasten the hinges to the box 2x M3 Nyloc Nut for the hinges 2x M3x35 Socket Head Screw DIN912 for the hinges 2x M3x5 Socket Head Screw DIN912 to hold the sliders on the railsPrinting: -"block" and the two hinge parts need to be printed twice -printing orientation see picturesInspired by: <a href="https://www.printables.com/model/543553-gridfinity-storage-box-by-pred-now-parametric" rel="nofollow">https://www.printables.com/model/543553-gridfinity-storage-box-by-pred-now-parametric</a>Gridfinity by Zack Freedman: <a href="https://www.youtube.com/watch?v=ra_9zU-mnl8" rel="nofollow">https://www.youtube.com/watch?v=ra_9zU-mnl8</a><h1>gridfinity</h1></div></div>

Gridfinity 5x5x6 box stackable with sliding lock

Gridfinity

橙豆造物

颜色是红色、黑色、白色还有金属铜。金属铜和甲板颜色一起能充当甲板。

Tianic1:800 泰坦尼克号1:800彩色打印

Figur

XH_Lab

IKEA SKADIS Homepod mini holder

Skadis

Lukas

Easter window pictures

Laser 

kerngebiet

<h3>Heat Set Insert Press</h3>With this conversion kit, the Paulimot drill stand can very easily be converted into a melting helper for thread inserts. Never again crooked threads or missing hands. ;)The print can actually be made in all materials. The holder for the LED ring should rather be printed in a more temperature resistant material, because of the possible heat development. Almost all parts do not need supports (only the mounting block for the LED ring needs smaller supports).<h4>For the assembly of the table you need:</h4><ul><li>4x - M4 thread insert</li><li>4x - M4*16mm</li><li>4x - M4 washer</li></ul>If you want to mount the LED ring or the Key holder, you also need a M6*10mm or M6*12mm screw.<h4>I have used the following parts:</h4><ul><li>Drill stand <a href="https://www.paulimot.de/Bohrstaender-mit-Arbeitstisch-43-mm" rel="nofollow">https://www.paulimot.de/Bohrstaender-mit-Arbeitstisch-43-mm</a> </li><li>Soldering iron <a href="https://amzn.to/3Le78aj" rel="nofollow">https://amzn.to/3Le78aj</a> * </li><li>Soldering Tips <a href="https://amzn.to/3JwM1Pq" rel="nofollow">https://amzn.to/3JwM1Pq</a> * </li><li>Threaded inserts <a href="https://amzn.to/41ZSLfH" rel="nofollow">https://amzn.to/41ZSLfH</a> * </li><li>Switch <a href="https://amzn.to/3mGOhKS" rel="nofollow">https://amzn.to/3mGOhKS</a> * </li><li>LED Ring 50mm <a href="https://www.ebay.de/itm/274098656178?var=574196945905" rel="nofollow">https://www.ebay.de/itm/274098656178?var=574196945905</a> </li></ul>For safety&#39;s sake, I mention that the assembly and use is of course at your own risk. Have fun with it!* = Amazon Affiliate Links

Heat Set Insert Press for Paulimot Drill Strand

Werkstatt

Markus710

I used this activ carbon: <a href="https://www.amazon.de/gp/product/B095PZLXPQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1" rel="nofollow">https://www.amazon.de/gp/product/B095PZLXPQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1</a>You have to watch out that your active carbon is a least Ø3mm otherwise it will fall out of the box. &nbsp;

Bambu Lab active carbon Box Filter

Bambu

IXPatch

To celebrate the 7th anniversary of Pokémon GO, I decided to make a little PokéStop spinner keychain :) It prints in place with no supports or assembly required.