mjrko84

deejay

Custom plate in 10 x 10, compatible with Lego Duplo. The plate can be built on from above and below.It is best to switch off the AUX fan.&nbsp;&nbsp;Custom Platte in 10 x 10, kompatiebel mit Lego Duplo. Die Platte kann man von oben und unten bebauen.Den AUX - Fan auf am besten ausschalten.

Plate 10x10 compatible with Lego Duplo

Duplo

Martin Kozak

<h3>Model</h3><ul><li>Model is 45 cm long, consists of 70 pieces and needs 720 g of PLA filament. Total print time is about 30 hours.</li><li>Biggest part is 214 x 118 mm and does not fit A1 mini build plate.</li></ul><h3>Postprocessing</h3><ul><li>Remove supports.</li><li>Use deburring tool to remove sacrificial bridging inside the holes.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/469116/2023-12-30_7f665c461fbba.jpg"></figure>&nbsp;<h3>Assembly</h3><ul><li>See attached assembly guide.</li><li>Due to the printer tolerances and nature of FDM printing, sometimes you'll need to apply more strength to assemble, some parts will be little loose and need a glue to secure it in position and whole drive train will need a lubrication in order to make it work smoothly (PTFE lubrication or silicion oil in spray recommended).</li></ul>See my other upscaled creation:<ul><li><a target="_blank" href="https://makerworld.com/en/models/114353#profileId-122927" rel="nofollow noopener">https://makerworld.com/en/models/114353#profileId-122927</a></li><li><a target="_blank" href="https://makerworld.com/en/models/133466#profileId-144784" rel="nofollow noopener">https://makerworld.com/en/models/133466#profileId-144784</a></li><li><a target="_blank" href="https://makerworld.com/en/models/146718#profileId-159991" rel="nofollow noopener">https://makerworld.com/en/models/146718#profileId-159991</a></li></ul>

Helicopter 300 %

Lego

Drunken_Monkey

Small collection of ISO 7010 Signs that may find a good use in your Bathroom.&nbsp;Included are:E001 – Emergency exit (left hand)E002 – Emergency exit (right hand)E003 – First aid&nbsp;M011 – Wash your handsM017 – Wear respiratory protectionM056 – Ventilate before and during entering&nbsp;P052 – No divingP061 – No jumping into water&nbsp;W009 – Biological hazardW016 – Toxic material&nbsp;The two-color signs can be created with a manual filament change, the three-color signs require an AMS&nbsp;&nbsp;

ISO 7010 Sign Collection for Bathrooms

Iso7010

BuzzEye

If you have AMS just use provided print profile&nbsp;Swap Instructions (if you do not have AMS): Start with black <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=43992830017755" rel="nofollow noopener">PLA Basic | Bambu Lab EU</a> At layer #6 (1.20mm) swap to Blue <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=42911327912155" rel="nofollow noopener">PLA Basic | Bambu Lab EU</a>At layer #8 (1.60mm) swap to Orange <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=42911327879387" rel="nofollow noopener">PLA Basic | Bambu Lab EU</a>At layer #11 (2.20mm) swap to Yellow <a target="_blank" href="https://eu.store.bambulab.com/en-pl/products/pla-basic-filament?variant=42911328043227" rel="nofollow noopener">PLA Basic | Bambu Lab EU</a>&nbsp;Experiment with other colors or use even more!&nbsp;You can scale up and down but only X and Y. Z axis must remain the same as original

Cat looking in the stars Van Gogh style Hueforge

Hueforge

Litophany 

blecheimer

This is a toy plane that is based on the famous Boeing Stearman Model 75 biplane. <a target="_blank" href="https://en.wikipedia.org/wiki/Boeing-Stearman_Model_75" rel="nofollow noopener">https://en.wikipedia.org/wiki/Boeing-Stearman_Model_75</a> The toy plane has a wingspan of 240mm and a length of 196mm. It can be completely assembled without using glue. All necessary clips and bolts are printed. I even included a small screwdriver.&nbsp;Use the following settings for the wings: 0,12 layer height, 4 walls, 4 bottoms, 8 tops, 16% gyroid infill The rest can be printed with 0,2 layers, 4 walls, 4 bottoms, 5 tops, 6% gyroid infill. I recommend a brim only for the bolts. See my 3mf for more details and how I positioned the parts on the build plates.&nbsp;Print the following parts with support:<ul><li>Fuselage (only for the cockpit)</li><li>Wings (only for th bottom of the threads)</li><li>Engine (not for the thread)</li><li>Bolts (only for the head)</li><li>Struts (use small tree support)</li><li>Supports (use small tree support)</li><li>Cockpit (only for the bottom of the thread)</li></ul>Do not use support on the threads.&nbsp;All parts will fit into a 200x200x200 build space.  A1 mini users need to split the wings into two parts (can be done with Bambu Studio) and glue them together after printing.&nbsp;For assembly follow these steps:<ul><li>put the front cover on the engine</li><li>screw the engine to the fuselage</li><li>insert the cockpit into the fuselage and secure it with a short bolt</li><li>insert the lower wing into the fuselage and secure it with a short bolt</li><li>insert the rear wing into the fuselage and secure it with a short bolt</li><li>this is now a bit tricky: insert the middle supports into the fuselage and put the top wing on the supports</li><li>now put one strut between the lower and top wing</li><li>insert a long bolt through the lower wing into the strut and screw it to the top wing</li><li>repeat for the other side</li><li>clip the propeller and the wheels with the pins to the plane</li><li>make funny engine noises and play with your new plane  </li></ul>Update 2023-12-11:Thanks to sgioja and CatWhisker I was able to correct two design flaws (cockpit + wings) and re-oriented the wing support in the print profile. The STLs and the print profile have been updated accordingly.&nbsp;Update 2024-02-17: User doppelt-05 made a very creative add-on to this model. He added a pinwheel propeller so that the propeller spins when the wind is blowing. You can find his model here on makerworld: <a href="https://makerworld.com/en/models/190364#profileId-210130" rel="nofollow"> https://makerworld.com/en/models/190364#profileId-210130</a>&nbsp;&nbsp;Disclaimer: This work by blecheimer is licensed under <a target="_blank" href="https://creativecommons.org/licenses/by-nc-nd/4.0/" rel="nofollow noopener">CC-BY-NC-ND 4.0</a>. You are not allowed to copy this model to other 3D printing websites without my permission.

Boeing Stearman 75 Toy Plane

Giocattoli

baris.ayarkan

Nice elephant because of the sitting it easy to print not need support only couple layers under its leg. I made 2 size 4 inch and 7 inch as an options but free to play with. Enjoy

Sitting Elephant

Statuette e home decor

maxaruta

This photobox features a 360-degree rotating base, which allows you to take photos from any angle. It is also fully customizable, thanks to the variety of wall styles available. With my photobox, you can significantly improve the perceived quality of your products to your customers. Your photos will be more professional and engaging, and your customers will be more likely to purchase them. Download the model today and start taking professional photos of your creations! _____________________________ Ti presento la mia nuova photobox, lo strumento perfetto per creare fotografie professionali delle tue stampe e creazioni.&nbsp;Questa photobox è dotata di una base d'appoggio ruotabile a 360 gradi, che ti permette di scattare foto da qualsiasi angolazione. Inoltre, è personalizzabile al massimo, grazie ai vari stili di pareti disponibili.&nbsp;Con la mia photobox, potrai migliorare notevolmente la qualità percepita dai tuoi clienti dei tuoi prodotti. Le tue foto saranno più professionali e accattivanti, e i tuoi clienti saranno più propensi ad acquistarli.&nbsp;Scarica il modello subito e inizia a scattare foto professionali delle tue creazioni!

Photobox: Take professional photos of your creations

Gadget Utili

uhltimate

Introducing the DIY Fly Swatter Gun, the ultimate weapon in your battle against mosquitoes. This 3D print model lets you build your own mosquito-swatting machine. Just snap the pieces together, no tools required! With a reach of 30cm, you'll have the upper hand in the mosquito-hunting game.&nbsp;IMPORTANT: "min. 4 Wall loops" if the spring has infill pattern, it will not work&nbsp;<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=Mk_qMPQVysw"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/Mk_qMPQVysw" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Fly Swatter Gun Card

Gadget Simpatici

Fyrby Additive

<h3>Design</h3>This model is designed to fit 100mm aluminium ventilation pipe, but will fit any 100mm flexible pipe that you can fix a clamp over to attach to these connectors.<h3>Useful Information</h3>There are two variants available. One has quite short protrusions for each pipe and one has longer ones which may be more convenient.The short version sits 150.5mm high on the print bed and the large version 210.7mm.<h3>Printing</h3>These were designed to be printed directly on the print bed with no supports with the end with two pipes on the print bed. They were strong enough for me in PLA using a print profile designed for strength.&nbsp;

Y Connectors For 100mm Pipe

Raccordi e simili

KYZ Design

This model was originally uploaded <a target="_blank" href="https://www.printables.com/model/452124-under-desk-drawer-with-double-travel-stops" rel="nofollow noopener">here</a>, check out the previous 50+ makes and comments<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/194310/2023-11-22_741ebdf3aad638.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/194310/2023-11-22_2ef855184807e.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/194310/2023-11-22_7e7782bb7c62a8.png"></figure>&nbsp;The remix adds built-in travel stops, added “tails” for stability when open, a double depth drawer version and more.&nbsp;Rails are designed for 6Gx20mm countersunk screws (or 4mm x 20mm)

Under Desk Drawer with Double Travel Stops

Cassetti e portaoggetti

revopoint

martin.taichl

This is my Rocinante model which is supposed to represent the Rocinante ship as it featured in the very last episode of the season 6 of the show Expanse. It has CSL plating, railgun, PDCs and torpedo tubes. The model is 50cm long and has several features. - Retractable PDCs - Posable landing legs - Retractable Airlock cover - Extendable Air-bridge. - Attachable stand Model is once again a kit so you do not need a glue (with one exception described in the assembly video). I highly recommend to look at this video to know, how to assemble everything together: <figure class="media"><div data-oembed-url="https://youtu.be/M02tMysBd8A"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/M02tMysBd8A" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Rocinante from the Expanse

Astronavi

toolmantim313

Simple rack to hold up to 10 build plates. Screws together with 3mmx14mm socket head cap screws. I included both 3mf and stl files with a multi color stand 3mf file, but it's not really necessary as it stands on it's own. Although since the stand does bolt onto the rack, you can use it to mount to the underside of a bench or shelf in the vertical position. I opted to use 3m tape and attached it to the side of the X1.&nbsp;And check out my Hex system adapter mounts so you can mount the rack to a hex wall!&nbsp;https://makerworld.com/en/models/28603#profileId-24991