mjm2420

E9-3D

Please consider supporting me with a boost on the new system, would love to have more recourses available to make and share Models!! Made this Headset stand of spiderman. Printet like a boss and now i have a cool place to store my headset slicer says floating object, just ignore this , it will print fine 0.2mm layerhight. No support. lightning infill 15 %. gyriod infill for the buttom part. 3 walls Make sure to check out my other headset stands. * Black Panther - https://makerworld.com/en/models/176323#profileId-193839 **Thanos - https://makerworld.com/en/models/162344#profileId-178199 ***Iron man - https://makerworld.com/en/models/126398#profileId-136594 ****Dead Pool - https://makerworld.com/en/models/140981#profileId-153593 Happy Printing

Spiderman Headset Stand

Gaming

Truffle

I was looking for a design that was simple, but looked good. There were designs here on MakerWorld, but there were a few problems with them that I didn't like. Most importantly is that they didn't have a simple, but nice design, the design did not come with a water hole at the bottom, and the designs didn't provide options in which you could either place a container with your plant into the pot or directly place the soil inside the pot. So I decided to make my design that provides a simple but nice design, ways in which you can place your plant inside the pot, as well as a water hole and a tray to catch the water. &nbsp;This design gives you the ability to either put the soil directly into the pot or to place a container within the pot that holds your soil. Also, this design has a drain at the bottom of the pot that allows the water to exit and enter the tray that stores excess water. (The tray has a maximum capacity of 75ml) Lastly if you place the soil directly into the pot there is a option to place a mesh that can hold the soil and let the water filter to the bottom.&nbsp;Dimensions: <ol><li>Pot: The opening has a circumference of 81 mm and height is 89.5 mm</li><li>Tray: The circumference of the tray is 105 mm, a height of 15 mm and a capacity of 75 ml of water</li><li>Mesh: The circumference of the mesh 79.5 mm and the height is 3 mm</li></ol>&nbsp;Note:<ul><li>If you have a plastic container that holds your soil and can fit within the pot nicely it's NOT necessary to print out the mesh.</li><li>I think it's best to either print this design in PLA MARBLE or BASIC WHITE PLA.</li></ul>

Flower pot with spiral design 

Garden

Zurlingo-3D

A fully articulated Dragon model with no support or post processing required.-Designed to be strong at full scale. -A Very easy, fast print. -Perfect to give as a gift. -Looks great with 'fuzzy skin' enabled in your slicer. -Can be scaled up or down to suit your needs (minimum around 25%)The rendered skin is a digital texture only and not part of the actual model<h2>3D PRINTING SETTINGS</h2>-0.4mm Nozzle Diameter. -=<0.2mm Layer Height. -10% Gyroid Infill. -3 Perimeters or more. -'Bridge Mode' On -4 Top/Bottom Layers -Use A Skirt Or No Build Plate Adhesion -No Support&nbsp;COMMERCIAL LICENSE IS AVAILABLE TO PURCHASE HERE: <a target="_blank" href="https://cults3d.com/:1558471" rel="nofollow noopener">https://cults3d.com/:1558471</a>

'HORNY DRAGON' - PRINT-IN-PLACE, ARTICULATED DRAGON - SUPPORT FREE

Dragon

Filar3D

Steampunk easters egg container!&nbsp;You can store small chocolate easter eggs or whatever you want :)&nbsp;Assembly Instructions: The egg has 5 parts<ol><li>Top</li><li>Bottom A1</li><li>Bottom A2</li><li>Side gear</li><li>Top Gear</li></ol><ul><li>Glue Bottom A1 to bottom A2</li><li>Insert side gear and top gear into Top (they pressure fit)</li><li>You dont need an AMS. The egg is designed so you can make color changes based on height.</li></ul>&nbsp;Wanna sell my designs? Join my patreon: <a target="_blank" href="https://patreon.com/filar3D" rel="nofollow noopener">https://patreon.com/filar3D</a>  &nbsp;

Steampunk Easter Egg Container

Easter

Maty505

articulated dragon model. resize for your needs.

Articulated Crystal Dragon

Things to Print

thingspatprinted

Build Difficulty: EasyThese are STL files used to create the 3D printed Buffalo Neon LED sign. Entire model is around 16 inches wide, 10.5 inches in height. Includes channels on the back to run wires for the connection between LED strips. Other materials used to build are listed below. I printed in 2 separate prints and used a soldering iron to melt the pieces together.&nbsp;Neon LED strips used: Red and Blue, 1 strip of each is enough:<a target="_blank" href="https://www.amazon.com/dp/B096FF6FSB?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">https://www.amazon.com/dp/B096FF6FSB?psc=1&ref=ppx_yo2ov_dt_b_product_details</a> &nbsp;12 volt Power supply:<a target="_blank" href="https://www.amazon.com/dp/B00FEOB4EI?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">https://www.amazon.com/dp/B00FEOB4EI?psc=1&ref=ppx_yo2ov_dt_b_product_details</a> &nbsp;Cable to attach end of Neon LED strip to on/off switch:<a target="_blank" href="https://www.amazon.com/dp/B01GPQZ4EE?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">https://www.amazon.com/dp/B01GPQZ4EE?psc=1&ref=ppx_yo2ov_dt_b_product_details</a> &nbsp;On/Off Switch:<a target="_blank" href="https://www.amazon.com/dp/B0895NVJLF?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">https://www.amazon.com/dp/B0895NVJLF?psc=1&ref=ppx_yo2ov_dt_b_product_details</a> &nbsp;Optional, instead of on/off a dimmable switch can be used:<a target="_blank" href="https://www.amazon.com/gp/product/B07KW4NCCJ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1" rel="nofollow noopener">https://www.amazon.com/gp/product/B07KW4NCCJ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1</a>

Buffalo Bills Neon Sign

Football

VRsculpts

Cute crochet style Pikachu. I have sized it to be a keychain but you can print it much larger if you wish, remove the negative keychain hole part in bambu slicer if you want it to just be a figurine.&nbsp;**Charmander, Squirtle, and Bulbasaur available on my Patreon (UPDATE no longer available on Patreon as of 2/1, I will make them available for purchase on my Cults3D page, discount available for paid Patreon subscribers), I will take requests for additional Pokemon from my Patreons as well! Join my Patreon if you would like to sell physical copies of my designs, your support is appreciated and motivates me to create more cool stuff to share! https://www.patreon.com/VRsculpts

Amigurumi Pikachu keychain

Pokemon

Gyroid

Coaster featuring Grogu from The Mandalorian. Simple design with 3 colours, easily painted in Bambu Studio or OrcaSlicer.&nbsp;Any layer height works, but lower will give better detail around the sides. Smaller line width might help with the detail, but overall a very easy model to print.&nbsp;IMPORTANTSince the top surface quality is important for the end result, make sure to have plenty of top layers. 4 or more is usually a good starting point.

Grogu (baby Yoda from The Mandalorian) coaster

Grogu

JamesThePrinter

Six versions are available:<ul><li>Little Debbie Christmas Tree - Bite<ul><li>Multi-Color</li><li>Single Color</li><li>No Ornament Loop</li></ul></li><li>Little Debbie Christmas Tree - No Bite<ul><li>Multi-Color</li><li>Single Color</li><li>No Ornament Loop</li></ul></li></ul>Check out the rest of my Christmas models <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/69417" rel="nofollow noopener">here</a>!&nbsp;&nbsp;Print SettingsMulti-Color Version - To ensure that the sprinkles don't easily break off, I sunk them about 1mm into the frosting. The downside of this is that the first couple top layers of frosting can be messy. To help with this, I used 5 top layers.&nbsp;Single-Color Version - no special settings are required&nbsp; <a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;&nbsp;The following filaments were used in the pictures above:<ul><li>Bambu Lab Matte Ivory White PLA</li><li>Bambu Lab Basic Bambu Green PLA</li><li>Bambu Lab Matte Scarlet Red PLA</li><li>Bambu Lab Matte Lemon Yellow PLA</li></ul>

Little Debbie Christmas Tree

Ornaments

chiz_m

If you like to show appreciation for the effort that went into creating this model, pls hit that BOOST button!&nbsp;A <a target="_blank" href="https://makerworld.com/en/models/18035#profileId-16764" rel="nofollow noopener">base/diorama builder</a> is now available for download for this mini figure model!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000018045/design/4fb50df1-8c36-4d0c-88ec-bcc8e5122b9c.jpg"></figure>___________<h3>IMPORTANT NOTE ON COMMERCIAL USE OF MY MODELS</h3>Please note that I am sharing my designs to any one to enjoy but for personal use only. I have NOT provided any commercial license to any one allowing the sale of 3d printed copies of my designs. Seeing my designs being sold for profit is discouraging for me to continue coming up with more designs. I will not hesitate to report to Etsy and other online sites if I find them being sold.__________This is a kit card of Minecraft Turtle in mini figure scale. Parts can easily be removed from the sprue without using cutters/clippers just by twisting the part.Default scale is comparable to the Minecraft mini figures but of course you can scale it up to as large as you want! :)<h4>Usage Options</h4><ol><li>Assemble as is and use as toy/collectible; or</li><li>Use the alternative part with loop and glue the halves together to make for a great keychain ornament!</li></ol><h4>Printing Reminders</h4><ul><li>Print as oriented, with NO supports needed.</li><li>If you&#39;re printing in multiple colors, please note that due to several color swaps, it would take longer to print.</li></ul><h4>Difficulty Level (Easy, Medium, Hard)</h4><ul><li>Printing: Medium - Bed should be leveled well to ensure small parts stick well to the build plate. Requires printing slower during the first few layers. May require lots of filament swaps if printed in multi-color.</li><li>Assembly: Easy - Parts should fit really easy. The flippers are intentionally designed to be loose and wiggly. See pictures for correct orientation of the flippers.</li></ul>

Minecraft-inspired Turtle Mini Figure Kit/Keychain

Keychains

lindh3d

I designed this to be printed without support and as one piece.It will take about 1kg of plastic and over 24 hours to print. But I think this is a super nice practical print to have at home or in the garden or when camping etc…&nbsp;Made a small update to my print-in-place portable stool. I also made an instruction video on how to open it up the correct way without breaking it or cutting it open.Perfect print to use up all those leftover spools with just a few grams of filament on.The weight limit is not tested to its full potential.My weight is 85kg and a friend of my have tested it and his weight is 90kg. No problem at all. I guess it will be able to withstand 120-150kg if you sit perfectly in the center and don't wiggle on it <img src="https://static.xx.fbcdn.net/images/emoji.php/v9/t80/1/16/1f92a.png">. It's a print-at-your-own-risk thing <img src="https://static.xx.fbcdn.net/images/emoji.php/v9/t83/1/16/1f60e.png">&nbsp;Rekommended printsettings:0.4 nozzle4 Parimiters0.16 layer height15-20% infill gyroid5 top/bottom layersSupport yes : Snug Support from build platePrint mode: Arachne&nbsp;<figure class="media"><div data-oembed-url="https://youtu.be/PND58IzI9xc"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/PND58IzI9xc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><figure class="media"><div data-oembed-url="https://youtu.be/VZa5Ko11Rl0"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/VZa5Ko11Rl0" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;EDIT: 231003More pegs for more weight support.0.1mm z offset for rings. this will make them tighter at first when printing making for easier and successful print. But more force when using the stool the first time is needed.&nbsp;EDIT: 231005 Added an extra chamfer on the inside ring to be able to take more force when disassembling the first time.&nbsp;EDIT: 231022 Larger holes on the top and bottom part for larger fingers :)Removed support for holes, new design can now use regular snug support for the top holes&nbsp;EDIT: 231203 After requests, I have now made a smaller kids version. This will also fit the A1 mini printbed size.

Portable stool (twist an sit)

Utility

mocodroid

Transformable Truck Robot. Ptint in place. Based on a Transformable movie character. Printed on PLA, .2mm layer height, .4 mm nozzle, 10% rectilinear infill, 4 top and 3 bottom layers. Use a brim if you have layer adhesion issues. No support needed. Move the joins side to side gently to free them.

Transformable Truck Robot Print In Place

Kids

BC Designs

Edit: Apols people, the print profile was oriented incorrectly which led to a few people having bridging issues, this is now corrected in the models main profile. Would advise ignoring the other profiles. Thanks to those that let me know! &nbsp;Because I'm sure most owners who have placed an order for spares have added a few filament cutters to the basket, why not use them :)&nbsp;Cuts flush @ 90 degrees.&nbsp;F360 screenshot attached as someone had mentioned this is a remix. It is not.&nbsp;Printing<ul><li>Included 3mf file setup at 0.20 layer height @ 15% infil</li><li>3 walls</li><li>No supports, the internal bridging is fairly clean and wont show/affect performance.</li><li>Seam set to the rear of the model to keep the logo clean </li></ul>Parts<ul><li>1 x Bambu labs original filament cutter</li><li>2 x m3 x 30. 2 came with the printer, packaging screws perhaps? </li><li>2 x springs. Mine measured around 4mm x 25mm long and were quite soft. </li></ul>Assembly<ol><li>Screw both screws into from the bottom and then drop the springs on. My screws (in picture) were not fully threaded and I suspect this made assembly much easier.</li><li>Insert filament cutter into the top section and insert a strand of filament to lock in place. Cut flush</li><li>Insert top into bottom, and screw together. Press fully down and tighten screws so they sit just inside the bottom piece.</li></ol>&nbsp;