meraner

panicozxb

I've done this charm for croc of pokemon's pokeball. I don't recommend printing just one, as the colors tend to blend when there are very small pieces with color changes. I hope you like it.&nbsp;&nbsp;He hecho este charm para croc de una pokebal lde pokemon. E. No recomiendo imprimir solo uno, ya que los colores tienden a mezclarse cuando hay piezas muy pequeñas con cambios de color. Espero que os guste

pokeball croc charm

croc

ljhtom (Javier Hernando)

Egg dispenser.This is the model created by me, ljhtom.Other similar model not linear, helical<a target="_blank" href="https://www.printables.com/es/model/250789-helical-and-rotary-eggs-dispenser" rel="nofollow noopener">https://www.printables.com/es/model/250789-helical-and-rotary-eggs-dispenser</a>&nbsp;Added files in neutral format for CADAdded split model to be printed on any printer.Always have fresh eggs, thanks to this dispenser, fill the dispenser with 12 XL size eggs, maybe 13 or 14 other sizes. .Model without supports (view image, you can only support in central area 75º, one piece, requires printing height of 300 mm.Added an optional anti-fall stop, it is not necessary, but it gives more security, it can be made in a soft materialIt only occupies 7 cm wide in your fridge, saving space, conventional dispenser 18 cm.&nbsp;02/12/23-- Added model with 20 mm more of support for the upper part to improve the hold.08/15/23 Add model slow down and photograph<h3>Print Settings</h3>Printer:Two trees Sapphire PlusRafts:Doesn&#39;t MatterSupports:YesInfill:10Filament:Fervi Esencial -Fiberlogy Petg PLA-PETG the one you like&nbsp;&nbsp;Category: Kitchen &amp; Dining

Eggs rotary Dispenser + slow down

kitchen

SavageLau

<h2>If you want a commercial license, check out my bio and get it from Patreon.</h2><h2>Personal use only.</h2>&nbsp;This model is design for MakerWorld light contest (2/5). Complete free version is only available on here Makerworld. <h3>Many people have contacted me said they willing to pay for the model. Other platform product manager reach and out said I could use their platform and selling this design for some money, but I have decided to keep it here for free for now. So there will be more people could enjoying it :) So show me your finshed print, I would like to see it. </h3><h3> Anywhere else you see this model upload is Unauthorized (please notify me and report them), beside my own account (SavageLau). </h3>&nbsp;<h2>If you would like purchase LED light needed for this design and filament from Bambu Lab Offical website: Affiliate link is below, so I can get some commission to support my future work. </h2><h2><a target="_blank" href="https://shrsl.com/4h4np" rel="nofollow noopener">https://shrsl.com/4h4np</a> </h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-03-23_4ad27b7082fe3.png"></figure><h2>Filaments that I use for this project: (Bambu Lab Offical website:)</h2><h2><a target="_blank" href="https://shrsl.com/4h4ns" rel="nofollow noopener">https://shrsl.com/4h4ns</a> </h2>&nbsp;&nbsp;&nbsp;<h2>You may also like this design:</h2>PeaShooter Lamp Kit 001. <a target="_blank" href="https://makerworld.com/en/models/174475#profileId-191833" rel="nofollow noopener">https://makerworld.com/en/models/174475#profileId-191833</a> &nbsp;&nbsp;&nbsp;My boss saw some Bellsprout light the other day and she want me to design one. I have one LED Lamp kit come with my a1mini and sitting for a while. So why not turning it into what she want. So the design started adpot the lamp kit into Bellsprout.I found this pic on Google, based on the posture and proportion started deisng.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_bc131748fd272.png"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-01_33679f29d502a.png"></figure><h2>Update: </h2><h3>2/2/2024. A new profile was made for a1mini. Increased infill/walls on base and body part. </h3>Model main body have been reduced in size inorder to meet the build plate size for a1mini with muti-color prints. &nbsp;<a target="_blank" href="https://makerworld.com/en/u/2010665163" rel="nofollow noopener">@Sascha2202</a> feedback it is a bit hard to keep banlance. Weight increased on printing profile by adding more infill and walls. Weight for that part from 160g to 202g, lowered center of gravity. Consider head is around 40g + led weight, it should do well now. <h3>2/1/2024. Joints redesigned. </h3>Improved joints firction load, strength, tolerancing. New turning angle sets around 13.5 degrees max for each joints. <figure class="image image_resized" style="width:36.72%;"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-01_d00693a8b7acb.png"></figure>“Head” part fit and finish improving. <h3>Revisions and Tests today:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_ffe7e41994dec.png"></figure>&nbsp;<h2>Before you print(Important!):</h2>Run the joint test print first with the filament you are going to use for joints and body, before you doing the full print! This is important. Depend on filaments you use for the joint parts, there will be sinkage rate difference, and firction load on joint will be different.&nbsp;I put very tight tolerancing on design, but it may not work as intended when you printing with your filaments, so run the test and confirm joints is very tight to each other. Other wise You will not get the desired result.&nbsp;&nbsp;Joints with other parts are standard size. There is one “Tight” profile for joints. There are two types of joint, regular and with wire clip one. You will need to print total of 12 or above (maybe less than 15) to get good proportion. &nbsp;Joints designed best work with 4 wall layers, and 10% to 20% infill, adding more infill will not improve the strength, will only leading part failure during assembly. &nbsp;<h2>Hard ware:</h2>This design require Lamp LED Kit 001 from Bambu Lab. All other parts are printable. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-31_bca061fd80f1d.png"></figure>&nbsp;<h2>Post work:</h2>Removing brims from all parts, when you remove brim from joints part, confirm it is fully removed. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_dec1b2c670225.gif"></figure><h2>Assembly:</h2>Refer these gif image. Joints is a bit hard to push in, refer how I do it, holding the bottom part with you fingure, it will reduce the change of failure. &nbsp;Joints:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_5c978e23e8634.gif"></figure><figure class="image image_resized" style="width:51.25%;"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_9f2e463b2d8a6.gif"></figure>Fully assembly:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_9a975d341b61f.gif"></figure>&nbsp;&nbsp;&nbsp;<h2>Design:</h2>Lamp kit is 60mm dia, 8mm thickness. based on that dims and make rough draft to evaluate the overall size.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_34bf66e6b20e5.png"></figure>&nbsp;Working on some parts, and integrate them in the end.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_4880a9ab2336a.png"></figure>&nbsp;I started with wanting ball joint on the head, so it will able to turn angles. End up why not to have more ball joints on the body.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_b08f0ea2e5ee9.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_80ec7f991cbaa.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_80ed16d7dd498.png"></figure>&nbsp;Ball joints is pain in the axx to work with. I want it to have a lot of friction load in normal condition. so the outter shell shall have very small tolerance to the ball or even smaller. Ended spending a lot of time try in truth to testing out different tolerances and make design revisions.Still not perfect, but it work for this application. You gain a lot of DOF, but it is a bit brittle, depends on your materials.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_153933e0ba5bb.png"></figure><h2>Revisions and tests:</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-31_641c974fd0d58.png"></figure>

BellSprout Lamp LED Kit 001

lamps

Layer by Layer

Build guide: <a target="_blank" href="http://danielnoree.com/the-openrc-f1-build-guide/" rel="nofollow noopener">http://danielnoree.com/the-openrc-f1-build-guide/</a>Questions & Answers: <a target="_blank" href="http://danielnoree.com/openrc-questions/" rel="nofollow noopener">http://danielnoree.com/openrc-questions/</a> OpenRC Electronics: <a target="_blank" href="http://danielnoree.com/openrc-electronics/" rel="nofollow noopener">http://danielnoree.com/openrc-electronics/</a>&nbsp;Complete hardware/electronics lists and kits available here: <a target="_blank" href="http://danielnoree.com/openrc-electronics/" rel="nofollow noopener">http://danielnoree.com/openrc-electronics/</a>Please respect the license under which this project is released. Thank you!&nbsp;Add your OpenR/C build to the buildmap: <a target="_blank" href="https://zeemaps.com/map?group=1888242" rel="nofollow noopener">https://zeemaps.com/map?group=1888242</a>&nbsp;&nbsp;This is the OpenR/C Formula 1 car. It's the third generation OpenR/C car and this time around focus is on simplicity! You can print everything in PLA except the tires which are done in NinjaFlex! Of course you can print it in any material you like but for those that want to print a car but only have PLA at hand, this is the project for you!&nbsp;Print the calibration cube to see if you need to fine tune your printer for the M3 nuts to fit in their pockets.&nbsp;A note on the servo saver. It's designed to be used with PLA, the upper and lower BOM applies force similar to a spring in a convetional servo saver. Of course the pressure depends on the type of material used, infill etc. Fine tuning can be done adding washer under or over the servo saver.&nbsp;The "Main Turning Vane's" needs to have it's lower part trimmed using a "exacto knife". Then slide it in the chassie plate and push it over the "Lid" and it should snap into place&nbsp;Parts that need support added: Front Spoiler.stl Front.stl Rear Rim.stl Rear Wing.stl Servo Saver Lower.stl&nbsp;Things to buy:Ok, obviously you need some filament which you'll get from your favourite filament supplier.You also need M3 screws and nuts which you can get at your local hardware store. Check the BOM list for what to get.Some bearings are needed as well, check the BOM list or buy a kit from FastEddyBearings.com: <a target="_blank" href="http://www.fasteddybearings.com/openrc-f1-sealed-bearing-kit/" rel="nofollow noopener">http://www.fasteddybearings.com/openrc-f1-sealed-bearing-kit/</a>&nbsp;Suggestion for electronics: <a target="_blank" href="http://danielnoree.com/openrc-electronics/" rel="nofollow noopener">http://danielnoree.com/openrc-electronics/</a>You can aslo ask questions in the Facebook group: <a target="_blank" href="https://www.facebook.com/groups/1111886228841596/" rel="nofollow noopener">https://www.facebook.com/groups/1111886228841596/</a>Short video: <a target="_blank" href="https://youtu.be/eTST_g2g2xQ" rel="nofollow noopener">https://youtu.be/eTST_g2g2xQ</a>Please consider supporting Daniel Noree on Patreon: <a target="_blank" href="https://www.patreon.com/DanielNoree" rel="nofollow noopener">https://www.patreon.com/DanielNoree</a>&nbsp;THIS IS A RE-UPLOAD RESPECTING THE ORIGINAL LICENSE: if you have any problems with any links let me know and i'll get them updated.

OpenRC F1 car - 1:10 RC Car

Alexis_

<h2>Rivals Party Dice</h2>Assembly instruction :&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/733249/2024-03-19_2af72e537b6968.jpg"></figure>&nbsp;<figure class="image image_resized" style="width:35%;"><img src="https://makerworld.bblmw.com/makerworld/draft/733249/2024-03-19_d59c809feb5dd8.jpg"></figure>&nbsp;&nbsp;_____________________________________________________________________________________________________________________________&nbsp;&nbsp;Check out more of my designs below and on my profile: <a target="_blank" href="https://makerworld.com/@Alexis_" rel="nofollow noopener">makerworld.com/@Alexis_</a>&nbsp;&nbsp;&nbsp;&nbsp;

Rivals Party Dice

dice

chiz_m

If you like to show appreciation for the effort that went into creating this model, pls hit that BOOST button!&nbsp;WARNING: Contains small parts. Not intended for children below 7 years old.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000038611/design/2023-10-10_8786f4c502dcc.jpg"></figure>A <a target="_blank" href="https://makerworld.com/en/models/18035#profileId-16764" rel="nofollow noopener">base/diorama builder</a> is available for download for this mini figure model!_____________<h3>IMPORTANT NOTE ON COMMERCIAL USE OF MY MODELS</h3>Please note that I am sharing my designs to any one to enjoy but for personal use only. I have NOT provided any commercial license to any one allowing the sale of 3d printed copies of my designs. Seeing my designs being sold for profit is discouraging for me to continue coming up with more designs. I will not hesitate to report to Etsy and other online sites if I find them being sold.__________Easy-to-assemble, quick print, kit card of Minecraft Spider in mini figure scale. Parts can easily be removed from the sprue without using cutters/clippers just by twisting the part.Print as oriented, with NO supports needed. Model comes with breakaway supports.Default scale is comparable to the Minecraft mini figures but of course you can scale it up to as large as you want! :)<h4>Usage Options</h4><ol><li>Assemble as is and use as toy/collectible; or</li><li>Use the alternative part with loop and glue the halves together to make for a great keychain ornament!</li></ol>

Minecraft-inspired Spider Mini Figure Kit/Keychain

minecraft

andythilo

Wanted to print this for a while but only just got around to it. Scaled to 150% which fits nicely on the Bambu's. I wanted to have a separate name plate to make printing easier so designed a new base similar to the original. The name plate can be painted in Bambu Slicer and is fixed to the base with 2 x M3 x 6mm screws of your choosing. &nbsp;I epoxyed the pole into the base plate, but left the skull un-bonded so it can be removed for show and cleaning.

T-Rex - Scaled to 150% + New Base

dani

phillip.b.brown

These are decorations for mini Christmas trees, perfect for your desk. To assemble each pokeball you need 1 top, 1 bottom, 1 middle ring and 1 button. The top and bottom are the same .stl file so you have to print it once white for the bottom and once red for the top. There is an optional top with a hook so you can easily tie a string to it and hang it that way. The Staryu tree topper prints in two pieces and is glued together. All parts are scalable for bigger trees. I used Bambu Labs PLA Basic Red, White & Black and Gold Silk PLA for the Staryu.

Mini Pokemon Tree Decorations

christmas

coufi2002

<h4>Print Settings</h4><ul><li>Rafts:</li></ul>No<ul><li>Supports:</li></ul>Yes<ul><li>Resolution:</li></ul>0,2<ul><li>Infill:</li></ul>15%

Wooden railway endstop by coufikus

trains

MrHanjak

⚫ Zetor 7745 ⚫&nbsp;👉INFORMATION👈I would like to announce that the Zetor 6341 will be the last tractor I will make in foreseeable future. At least for a year, I want to take a break from the tractors. Right now I want to focus on sci-fi or fantasy models. I want to stop using glue and have complete models without glue. Which is not very possible with a tractor. So look forward to the new models!&nbsp;&nbsp;!!!Warning!!!Not suitable for small children. The model contains many small parts, risk of inhalation and suffocation.&nbsp;If you like my work, I will be very happy if you support me by giving me a follow and subscription on YouTube. If you have any ideas for models, you can write me your suggestions :-) Soon I will add an update for already existing Zetors so that something can be connected to them + some machine or trailer.&nbsp;This tractor is designed to be beautifully assembled. ✅ ➖➖➖➖➖➖➖➖➖➖➖➖➖➖➖ Follow me on YouTube for more info about what you can look forward for. ■ YouTube ➔ <a target="_blank" href="https://www.youtube.com/c/MrHanjak2017" rel="nofollow noopener">https://www.youtube.com/c/MrHanjak2017</a> ■ Video<figure class="media"><div data-oembed-url="https://youtu.be/u6RwfhFYF5g?feature=shared"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/u6RwfhFYF5g" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>🔳 INFO 🔳■ Steel sheet ➔ PEI■ Nozzle ➔ 0.4■ Material ➔ PLA■ Infill ➔ 15%■ Circuit ➔ 3■ Supports ➔ NO&nbsp;🔳Change of color + Brim🔳Brim is individual - I can't tell you where yes and where not, it depends on how well your printer is calibrated. And how does it hold up on your steel sheet. So I'll leave it up to you. I don't need a brim almost anywhere.➔ Red_ORANGE-50 - change color [0.95] + BRIM<img src="https://media.printables.com/media/prints/603808/rich_content/7e18e873-4b9a-4db4-8a62-1c744858191d/image.png"> ➔ 50 Orange_WHITE-49 - change color [1.55] + BRIM<figure class="image"><img src="https://media.printables.com/media/prints/603808/rich_content/39ec2abf-d75d-45db-8685-445edaf8cf17/image.png"></figure>&nbsp;➔ Orange_RED-48 - change color [1.55] <figure class="image"><img src="https://media.printables.com/media/prints/603808/rich_content/a6444a41-dc7f-499e-bd1e-67efbe1eaea2/image.png"></figure>&nbsp;➔ Black_RED-46 - change color [17.15]<figure class="image"><img src="https://media.printables.com/media/prints/603808/rich_content/85fbdb00-4072-4ba1-a0f0-4102e6493cea/image.png"></figure>&nbsp;➔ Black_WHITE-47 - change color [2.15] <figure class="image"><img src="https://media.printables.com/media/prints/603808/rich_content/90869b3b-4ed8-43e7-a867-580efb043ce3/image.png"></figure>&nbsp;➔ Red or DarkSilver -7 - BRIM<figure class="image"><img src="https://media.printables.com/media/prints/603808/rich_content/4c40c768-929c-4521-ad91-bf85c1e026bb/thumbs/cover/800x375/png/br.webp"></figure>&nbsp;&nbsp;&nbsp;&nbsp; More models coming soon! 😉🔳 Model created by MrHanjak 2023 🔳