mcampbell371

ATTV85

for 19mm strapmake from ABS or PET-G

Quick Release Buckle

Functional

laisch

<h3>HUGHES MD - 500 (flyable pullcopter) </h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_sman5x65txu7.gif"></figure>&nbsp;&nbsp;<h3>Externals</h3>For launching the MD-500, you need to make the “<a target="_blank" href="https://makerworld.com/de/models/81500" rel="nofollow noopener">Overpowered Heli Launcher</a>” before:<figure class="image"><a href="https://makerworld.com/de/models/81500" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_cmrmg9lwcdhu.jpg"></a></figure>&nbsp;<h3>Printingsettings</h3>Print as light as possible. I used 2 perimeter, 0.2mm layerheight and 10% infill on the helicopter body.For the Rotor use Arachne in the slicer.&nbsp;<h3>Postprocessing</h3><figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_n770l86x94u8.jpg"></figure>Clean the hole for the shaft with an 8mm drill bit. Make it as clean as possible to avoid friction.</td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_41bpt3jnpijj.jpg"></figure>Add the pins to the body and glue the two haves together with some superglue</td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_bb2k67jpmjiq.jpg"></figure>Add a drop of superglue into the skid holes and glue the skids in place</td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_huhj8w7d9shl.jpg"></figure>To make the helicopter fly stable, you have to direct the airflow of the propeller to act as a counterforce against the rotors spinning direction. The easiest way is to make a fin with transparent tape.</td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_i9cggf52mewy.jpg"></figure>You have to adjust the sice and angle of the tape according to your friction on the shaftTestfly -→ adjust → repeat …</td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_61dldorkdcxe.jpg"></figure>Mount the rotor to the shaft. It should be friction fit, but if its too lose you can add some superglue. (The rotor should spin freely)</td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_etlatpk1760y.jpg"></figure>To stop the helicopter from rotating during the launch, you have to add the helistops to your launcher. Just remove the old M3x6 screw and replace it with a M3x10.</td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/239508/2023-12-06_7efl5p749tfj.jpg"></figure>Have Fun</td></tr></tbody></table></figure>&nbsp;

MD-500 (flyable Helicopter)

Romwba3D

A Festive Grinch andles split for multi-colour printing, also split to enable printing with just one AMS or all in one with more than one AMS.&nbsp;i have also included a single colour STL file single colour or resin printing&nbsp;I have uploaded 3mf Print profiles for both the X1C/P1P and A1 Mini &nbsp;These are part of My Patreon <a target="_blank" href="https://www.patreon.com/romwba3d" rel="nofollow noopener">https://www.patreon.com/romwba3d</a>&nbsp;You can view all the Available Models - now over 220 models on https://www.romwba3d.com

Functional

fun

Holiday