mblack24

Sevro

Instruction how to train your dragon.After printing, you have to make some bends.The most important is bending of the tail a little up.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/707210016/draft/2023-08-14_742i3oxai92n.jpg"></figure>You can also bend it a little into V shape<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/707210016/draft/2023-08-14_8ysm4b56u0cv.jpg"></figure>Next important thing is bending of wings a little bit up.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/707210016/draft/2023-08-14_uwh80du8jcaq.jpg"></figure>Beyond that you can play with middle small wings and bend it up or down or just leave them as they are.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/707210016/draft/2023-08-14_46milndjqctn.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/707210016/draft/2023-08-14_owq4oq6r94ge.jpg"></figure>With version 2.1 you don't have to add ballast to the head. With 100% infill and PLA, dragon should be good balanced.If you accidentaly printed dragon with lower infill than 100%, add play-doh or plasticine to the head and it will be flying too.Sometimes the model is demand a little refresh shape after hard landing. Good throw technique is also important. Throws it like paper airplane. Prepare that not every flight will be good. But if you train the dragon a little then smooth flight is very satisfactory :)PrintingPrint in place with PLA, with 100% infill (for proper head ballast) and 0.2 mm layer height. You have to have good bed leveling, because wings and tail have only one layer height. With my prusa mk2 with 0.6 nozzle it takes about 30 minutes. FilesThe model has two versions One without horns to quickly print and fly.Second one with horns on the back to fix it to the ceiling and for a better look :) Horns fix with superglue.Besides, there is a desk stand, wall sticker and ceiling hanger. To stick it to the surface, use double side tape. Print it with layer height whatever you want.Flights Below some outdoors exemplary tweaks nad flights.Version 2.1 without ballast. Flights were performed with windy condition so dragon was a little nervous :)<figure class="media"><div data-oembed-url="https://youtu.be/N9rLLoG5ESg"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/N9rLLoG5ESg" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>Version 1 with balast.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/707210016/draft/2023-08-14_daiibxm95bxl.webp"></figure><figure class="image image-style-align-center"><img src="https://makerworld.bblmw.com/makerworld/user/707210016/draft/2023-08-14_unilyl8lzdjy.gif"></figure>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

Flying Night Dragon

Dragons

Black Glovz

Basic Witch Coffee Coaster

Coffee Coffee Coffee

jwalker55

Similar to my other “Wavy Vase” but with a lattice style

Wavy Lattice Vase

Decor

Dingus Dude

To be sure you're always downloading the most up to date file, use my “DD” profiles. See changelog below for detailed updates.&nbsp;BetterBoxPrint In Place Double Storage Customizable Divider Parts BoxNot just for Bambu Lab parts! Makes a great jewelry box, too!&nbsp;This is another version of my Print In Place Hinged Box and part of my BetterBox series!Check out the rest of the lineup below to find the ones that fit your needs!<figure class="table" style="float:left;width:35%;"><table class="ck-table-resized" style="border:2px solid hsl(0, 0%, 100%);"><colgroup><col></colgroup><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/45645#profileId-47422" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/377353/2023-10-28_e2af4207409738.jpg"></a></figure></td></tr><tr><td style="border:2px solid hsl(0, 0%, 100%);"><a target="_blank" href="https://makerworld.com/en/models/22697#profileId-20609" rel="nofollow noopener">BetterBox</a> <a target="_blank" href="https://makerworld.com/en/models/45645#profileId-47422" rel="nofollow noopener">Customizable Dividers</a></td></tr><tr><td><figure class="image"><a href="https://makerworld.com/en/models/22697#profileId-20609" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/377353/2023-10-27_f53e9d31a992f8.jpg"></a></figure></td></tr><tr><td style="border:2px solid hsl(0, 0%, 100%);"><a target="_blank" href="https://makerworld.com/en/models/22697#profileId-20609" rel="nofollow noopener">BetterBox</a> <a target="_blank" href="https://makerworld.com/en/models/22697#profileId-20609" rel="nofollow noopener">Original Bambu Parts Box</a></td></tr><tr><td><figure class="image"><a href="https://makerworld.com/en/models/45918#profileId-47727" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/377353/2023-10-27_50d65c4b44a158.jpg"></a></figure></td></tr><tr><td style="border:2px solid hsl(0, 0%, 100%);"><a target="_blank" href="https://makerworld.com/en/models/22697#profileId-20609" rel="nofollow noopener">BetterBox</a> <a target="_blank" href="https://makerworld.com/en/models/45918#profileId-47727" rel="nofollow noopener">Empty Storage Box</a></td></tr></tbody></table></figure>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;-Now back to the box that you came here for-&nbsp;FEATURES:&nbsp;Print In Place Hinged Box&nbsp;Compartments:<ul><li>Fully customizable! Use all the included dividers or print any of the ones you want plus more. Whatever you want to store, this box can accommodate. Please share how yours is arranged! There are litterally HUNDREDS of variations! Mix and match divider colors to help organize!</li></ul>Flip Top Lid:<ul><li>Allows for double the storage! The Flip Top prints on a separate plate and is super easy to install. When the Flip Top snaps closed it sits tight to the top dividers so even the tiniest screws won't fall out or move to another compartment! In short, your parts STAY where you put them!</li></ul>&nbsp;Flip Top Installation:<figure class="table" style="float:left;width:50%;"><table style="border:2px solid hsl(0, 0%, 100%);"><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/377353/2023-10-31_5a34a1d06579c.gif"></figure></td></tr><tr><td style="border:2px solid hsl(0, 0%, 100%);"> </td></tr></tbody></table></figure>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;Box Dimensions175mm length107mm width (not including hinge and latch)61mm height (closed)&nbsp;&nbsp;&nbsp;Of course it's not necessary but if you want to add to my <a target="_blank" href="https://paypal.me/davebarbier?country.x=US&locale.x=en_US" rel="nofollow noopener">beer fund</a> it would be much appreciated! 😄&nbsp;

BetterBox - Flip Top Storage Box

Boxes

Kit Crafters

<h2>MINI-CITY</h2>Welcome to MINI-CITY, where you create and customize your own city from the ground up. Starting with a tileable base plate, you can print out an array of building from a wide variety to choose from to begin piecing together your very own miniature metropolis. This first set of the MINI-CITY series comes with a modern house series, an apartment complex series, a tower series, an office series, and miscellaneous buildings to complete your very own city.&nbsp;Let me know what you think! I plan to make more buildings, baseplates, and other additions to this series and your support is greatly appreciated!<h3>Instructions:</h3>To make sure your building fit well into the base plate, try printing the fitment test profile to see if you need to adjust your X-Y hole compensation/contour compensation.&nbsp;This is my setting for SUNLU PLA+. The Bambu Lab PLA Basic filament works well with the default settings. <img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_7867989c75297.png">&nbsp;After your fitment test, try printing out one of the building series with a base plate or the profile with one of every building! The profiles provided have a color change right where the building starts to print so that the ground can be a color of your choosing and the building can be a different color. All buildings have the same color transition, thus minimizing the number of color changes to just one!&nbsp;There are several baseplates available, the largest one includes a hill, slanted streets, and the ability to connect with more baseplates.&nbsp;Try mirroring any of the buildings and baseplates to add variety and depth to your city as well.&nbsp;<h3>Modern House Series:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_c0dd505587ddb.jpg"></figure><h3>Apartment Complex Series:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_6ffa89a71cbad.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_446e131b2fd4f.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_cc90e3ce08d95.jpg"></figure><h3>Tower Series:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_8d10d5e35d404.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_e8740fe92ecaa.jpg"></figure><h3>Office Series:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_50d7b0bdf33d9.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_e737526f6ac7c.jpg"></figure><h3>Misc. Series:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/115334/2023-10-23_0f6754d483f74.jpg"></figure>

MINI-CITY - Modular Miniature City Blocks

Buildings

Bookmarks

RestoreDoctor

Update: 26.07.2023 - added feets without support to use your own settings in the slicer. Settings:<ul><li>0.20mm Standard </li><li>support needed </li><li>PLA / PETG </li></ul>Hardware:<ul><li>2pcs. M3 x 10mm Cylinder Head (hands)</li><li>2pcs. M6 x 10mm Cylinder Head (arms)</li><li>2pcs. M6 x 35 mm Cylinder Head (hinge)</li></ul>The supports for the drawer must be removed from the FEETS after printing - see below <figure class="image"><img src="https://media.printables.com/media/prints/504936/rich_content/33828916-0289-4448-94cc-3efca0f998cf/f39fe2f4-eceb-4f29-aab0-e56c3afd4f1f.webp"></figure>

Robot Desk Organizer

Pen Holder

chiz_m

If you like to show appreciation for the effort that went into creating this model, pls hit that BOOST button!&nbsp;Santa Hat now available! <a target="_blank" href="https://makerworld.com/en/models/75526#profileId-80041" rel="nofollow noopener">Download it here!</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000018267/design/2023-11-29_8d14c8695d84a.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000018267/design/c6564a0c-3193-4ced-8e44-9405fcfbcfb3.jpg"></figure>A <a target="_blank" href="https://makerworld.com/en/models/18035#profileId-16764" rel="nofollow noopener">base/diorama builder</a> is now available for download for this mini figure model!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000018267/design/e5f6d4cc-3842-40ac-a7e3-cb275c3670fa.png"></figure><a target="_blank" href="https://makerworld.com/en/models/18035#profileId-16764" rel="nofollow noopener">Download the different tiles here</a> for the Enderman to carry around!_____________<h3>IMPORTANT NOTE ON COMMERCIAL USE OF MY MODELS</h3>Please note that I am sharing my designs to any one to enjoy but for personal use only. I have NOT provided any commercial license to any one allowing the sale of 3d printed copies of my designs. Seeing my designs being sold for profit is discouraging for me to continue coming up with more designs. I will not hesitate to report to Etsy and other online sites if I find them being sold.__________Easy-to-assemble, quick print, kit card of Minecraft Enderman in mini figure scale. Parts can easily be removed from the sprue without using cutters/clippers just by twisting the part.Print as oriented, with NO supports needed. Model comes with breakaway supports.Default scale is comparable to the Minecraft mini figures but of course you can scale it up to as large as you want! :)<h4>Usage Options</h4><ol><li>Assemble as is and use as toy/collectible; or</li><li>Use the alternative part with loop and glue the halves together to make for a great keychain ornament!</li></ol>__________Thanks to the wonderful folks from <a target="_blank" href="https://sparta3d.ca/" rel="nofollow noopener">Sparta3D.ca</a> for giving me the opportunity to try their Chameleon and Galaxy PLA filaments! Great PLA filaments all around! I did my usual initial test print to make sure the filament are calibrated to meet the required clearances/tolerances of my mini figure models and got the kits printed in my first try! No bed adhesion issues, superb surface finish, no AMS jamming issues! All around great filament performance! Try their filaments today esp. if you&#39;re located in Canada!&nbsp;

Minecraft Enderman Mini Figure Kit/Keychain

Minecraft

Kit Cards

WizPrint3D

Introducing our 3D-printed multicolored Pikachu keychain! This delightful accessory captures the essence of everyone's favorite Pokémon in vibrant hues. Attach it to your keys or bag and let Pikachu's cheerful spirit accompany you on your adventures. A must-have for Pokémon fans and collectors, this keychain is sure to brighten your day!&nbsp;AMS ready profile, gotta print em all!&nbsp;NOT FOR COMMERCIAL USE&nbsp;If you want to support me and are interested in selling my items, please visit:https://www.patreon.com/WizPrint3D

Happy Pikachu Keychain

Pokemon

remi.rafael

<div><h1>Summary</h1><div>Those designs are different types of nozzles and a cork for seal guns. You can chose nozzle sizes between 2 and 5 mm. I like the 2mm for delicate works. All models can be printed without support and need no post treatment. For a smooth result use 0.4 layer thickness. The walls are designed to be to layers thick.Edit: After being asked in comment i added 2 models with 1mm holes: "1mm.STL" and "1mm_thin_walls.STL". The first one uses the exact same design with 0.8mm walls but it seemed like a precise work requiring 1mm holes would be wasted by 1.6mm of plastic. So the second model "thin walls" uses 0.4 mm walls. High pressure might break it so bee cautious and don't hesitate to give feedback on those models.</div></div>

Seal gun nozzles and cork

Tools

Williams Industries

Makes a great pin, magnet, coaster, keychain, or scale it up for some sweet wall art&nbsp;We have a lot of great stuff over at the Patreon: <a target="_blank" href="https://www.patreon.com/WilliamsIndustries" rel="nofollow noopener">https://www.patreon.com/WilliamsIndustries</a>

Mario Star

Mario

COSE-JERRY

make sure to disable the aux fan, the part is too close.&nbsp;you can purchase one herehttps://www.ebay.com/itm/115660839209

NASA Meatball Logo

Space

Crafty Sven

No supports needed. Make sure that the bed is clean and the first layer adheres properly, glue is recommended.&nbsp;Good luck and happy printing ! ^-^&nbsp;I suggest trying the non AMS version 1st to see if you like the design and size. &nbsp;You can scale this up to 150% !

Ancient Guardian Articulated from Zelda 

Zelda

bensbigolbeard

<h2>An Icosahedron made of bevel gears.</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461626/2023-10-04_58621e1768a8e.gif"></figure>&nbsp;<h3>Assembly</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461626/2024-01-27_56dec3bf3a3588.gif"></figure><h3>Text Assembly Instructions:</h3>Some folks have had trouble following the video above (sry, it's not as clear as I'd hoped), so here are some alternate instructions. The image shows the process, working from top left to bottom right.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461626/2023-10-22_97301cb6256.png"></figure>Image 1<ul><li>The first image above shows two large gears attached to the core, with one small gear in between them.</li><li>Point the larger gears' pointed teeth straight up (i just took the pin out on the opposite side, so it could sit flat for the pic). These points are indicated in red in the image.</li><li>Looking at the small gear, locate the three sides of the small triangle on the back and make sure that the insets (indicated with red “V”s in the image) are angled to accept the larger gears' pointed teeth.</li><li>You should then be able to add the next large gear with the point up, like you see in the first image.</li></ul>Image 2<ul><li>The second image shows the model flipped over 180 degrees, sitting on flat of the small gear that was just on top</li><li>Stick on the last large gear to the pin pointed up (it can be in any orientation at first)</li></ul>Image 3<ul><li>Find an empty gear slot and point it upwards.</li><li>Orient the large gears so the points are now pointing up around the empty small gear slot, similar to their orientation in the first image.</li><li>Pop in the small gear, with those triangle corner inset areas accepting the large gears' points</li></ul>Image 4<ul><li>repeat the previous step until all of the empty small-gear slots are file</li></ul>That should leave you with everything in the correct arrangement! The pins will fully seat after the initial turns, so you might hear them pop into place. If you still encounter issues, I'm active in the comments and would be happy to help troubleshoot.&nbsp;Background: I love <a target="_blank" href="https://www.printables.com/model/245028-three-cube-gears" rel="nofollow noopener">this gear cube</a> and it made me want to explore how to apply that approach to other platonic solids. For some stupid reason I picked the Icosahedron and the additional geometric complexity kicked my butt days. It would have probably been easier if I could math good, but that's not the case… I still prefer how much the gear cube deforms so significantly in it's intermediate states, but the icosahedron is still a satisfying fidget. I might explore some alternative ways to break up the shape to introduce some more deformation, while retaining the smooth gearing. Printing notes:<ul><li>If the gears begin to get loose, replacing the pins with newly printed ones will likely tighten it right up.</li><li>To that end, printing the pins in a more friction resistant material and adding a bit of grease/lubrication can extend their life</li></ul>Print profile updates (for the ones I've uploaded): 10/8/23:<ul><li>Print order changed to outer/inner/infill for better dimensional accuracy</li><li>Brim added to pins for improved bed adhesion for most plate types</li><li>New pins only profile, in case you still have bed adhesion issues or need a fresh set, if the originals wear out</li></ul>10/22/23:<ul><li>I updated the stand-alone STL and 3mf files to include the brim and orientation tweaks from the previous update</li></ul>

Icosahedron Gears Fidget Toy

Fidgets

Lofted Goods

A mid century modern vase.&nbsp;No supports needed. Easy print. Can be scaled up or down however you like.&nbsp;Filament and hardware/non 3D printed items for this model can be found on my Amazon Storefront, linked here: <a target="_blank" href="https://hendricks.design/links/" rel="nofollow noopener">https://hendricks.design/links/ </a>

MCM Vase

Vase

JamesThePrinter

Candy cane halves spiral around each other.Print the model twice. The two half should slide together as you twist. Once together, hold it in one hand. Push together the top of one piece and the bottom of the other piece. This should slide the pieces in opposite directions. Then push on the opposite ends to reverse. You can slide them about half way without them falling apart.If you would like to use these as decorations, glue the two halves together.&nbsp;Check out the rest of my Christmas models <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/69417" rel="nofollow noopener">here</a>!&nbsp;Print SettingsStandard settings will work, but I used the following:<ul><li>0% infill</li><li>3 perimeters</li><li>5 top layers</li><li>Wide brim (8-10mm)</li></ul>As with any tall model, it can get a bit wobbly near the top. Removing the infill allows for smooth, even movements to minimize the wobble. Also, be sure to cleanly remove the brim to avoid any extra friction during use.At first, they may be a little tight. However, they loosen up some as you play more with it. As they slide back and forth, they are rubbing away any imperfections to make smooth mating surfaces. The original model has a 0.2mm clearance between the pieces. I have included a higher clearance (0.3mm) version for anyone who is getting a very tight fit. The original model will work for almost everyone.&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>polymaker PolyTerra Lava Red PLA</li><li>Sunlu PLA White</li><li>CC3D Flame Orange PLA+</li><li>Prusament Azure Blue PLA</li><li>polymaker PolyTerra Forest Green PLA</li><li>Fillamentum Lilac PLA</li><li>Fillamentum Wizard's Voodoo PLA</li><li>Inland Tough PLA Pink</li><li>PrintBed Baja Blue PLA</li><li>polymaker PolyTerra Pastel Banana</li><li>MatterHackers Quantum Blue Yellow PLA</li><li>MatterHackers Quantum Silver Gold PLA</li></ul>

Candy Cane Fidget

Christmas

Kardes.Design

Update: Amazing 11 panel <a target="_blank" href="https://makerworld.com/en/models/61376#profileId-63895" rel="nofollow noopener">collection</a> done by <a target="_blank" href="https://makerworld.com/en/u/3946821223" rel="nofollow noopener">Superus</a> and also dozens of new panels are available in this <a target="_blank" href="https://makerworld.com/en/u/2706903410/collections/57878" rel="nofollow noopener">collection</a> Model&nbsp;I wanted to have a lamp that can be customized and changed while having a futuristic and modern look. The base model has a pattern that achieves an optical illusion as you can see in my Assembly video here. It's very simple with no glue or extra hardware.https://www.youtube.com/watch?v=gBAowd_ECU0&nbsp;I created this futuristic looking lamp with swappable panels that can be remixed with all your favorite characters or patterns. I will be adding more panels and will try to make custom panels upon requests in the comments. (New Dragon ball inspired collection released! <a target="_blank" href="https://makerworld.com/en/models/35292#profileId-32809" rel="nofollow noopener">https://makerworld.com/en/models/35292#profileId-32809</a> )&nbsp;I will upload the raw STEP file of the panels as a separate project for the community to remix as they wish.&nbsp;https://makerworld.com/en/models/31480&nbsp;Print Instructions.&nbsp;I have uploaded a 3mf files with the recommended settings and pre supported&nbsp;Main structure:&nbsp;Extremally low amount of support needed (Painted support)&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/160978/2023-10-02_9915021e7ad94.png"><img src="https://makerworld.bblmw.com/makerworld/draft/160978/2023-10-02_0cbc2559b7af3.png">Layer height: 0.2Infill: 5%Walls: 2Bottom/top layers: 4Panels with built in light diffuser:<img src="https://makerworld.bblmw.com/makerworld/draft/160978/2023-10-02_8d8e06fd386be.jpg">The right panel has a built in light diffuser that is modeled as a separate object which can be changed in the slicer to a white filament using the AMS or by adding a pause and changing filament without an AMS. This type (Panel with built in diffuser) can accommodate more complex designs since the design does not have to be a continuously connected print like the example on the left. &nbsp;&nbsp;First layer width: 0.55 ( to make sure that the 2 layers of the diffuser stick together well)Layer height: 0.2Infill: 5%Walls: 2Bottom/top layers: 4&nbsp;Panel without diffuser:&nbsp;Very simple to print. Only requires the diffuser to be printed in vase mode separately. only one diffuser is needed for all 3 panels.Layer height: 0.2Infill: 5%Walls: 2Bottom/top layers: 4&nbsp;Diffuser:<img src="https://makerworld.bblmw.com/makerworld/draft/160978/2023-10-02_4796306e51b11.jpg">Print in vase mode with 0 bottom/top layers. It will work perfectly even if its not printed perfectly straight. like this wonky example here.&nbsp;Hardware:&nbsp;&nbsp;Only 2 parts are needed1: A power cord with a e27 attachment like the one i got here for 4 eurosthis attachment has a thread diameter of around 39.3 mm and an outer right of around 44 mm.The whole in the lamp is 40 mm so you just need the included cap to secure it. &nbsp;If you have other sized cords please let me know so that i can release more hole sizes.<img src="https://makerworld.bblmw.com/makerworld/draft/160978/2023-10-02_2ecf52b872678.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/160978/2023-10-02_4a4b4bc3753b6.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/160978/2023-10-02_84f981f479d4d.jpg"><img src="https://makerworld.bblmw.com/makerworld/draft/160978/2023-10-02_a658987c90106.jpg"> <a target="_blank" href="https://www.aliexpress.com/item/1005005164587104.html?spm=a2g0o.order_list.order_list_main.36.6d1979d2ai4Dj2&gatewayAdapt=glo2nld" rel="nofollow noopener">https://www.aliexpress.com/item/1005005164587104.html?spm=a2g0o.order_list.order_list_main.36.6d1979d2ai4Dj2&gatewayAdapt=glo2nld</a>&nbsp;2: A multi color bulb. I got one from a local store here for 4 euros but you can find them anywhere. they come with a remote or an app. I prefer the one with a remote like the one here.&nbsp;<a target="_blank" href="https://www.action.com/nl-be/p/3007108/multicolor-ledlamp/" rel="nofollow noopener">https://www.action.com/nl-be/p/3007108/multicolor-ledlamp/</a>&nbsp;Hi, I'm a student and an aspiring designer. I'm so grateful for the support I've received from people like you. Your support means the world to me, and I'm excited to share my work with you. You can find links to my donation pages below:&nbsp;<a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=6VL4LD2NAJJ86" rel="nofollow noopener">https://www.paypal.com/donate/?hosted_button_id=6VL4LD2NAJJ86</a><a target="_blank" href="https://www.buymeacoffee.com/KardesDesign" rel="nofollow noopener">https://www.buymeacoffee.com/KardesDesign</a>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

Mystic lamp with swappable panels

Lighting

Neebick

Update: I have added a <a target="_blank" href="https://makerworld.com/en/models/146363#profileId-159384" rel="nofollow noopener">scabbard</a> that is designed for this Master Sword.&nbsp;This one was a fun project to see if I could make a master sword that would could be all encompassing for its appearances in Tears of the Kingdom. The party trick being that the center jewel acts as a locking peg for which ever blade is inserted. It's modeled with a tight tolerance so that it will friction fit in. Just press the center of the jewel and the peg will slide out. This allows the blade to be removed. My idea was that this would be more convenient then printing and finishing 3 different hilts for each blade. Storage should be easier as well. Plus its just cool.&nbsp;Glue and supports will be necessary for some parts.&nbsp;I have kept tolerances tight on some parts to help with friction fitting. I've found the blades need a couple insertions before it becomes easier. I figured this was better then a wobbly blade.&nbsp;<h3>Parts</h3><ul><li>Blades - Each blade is designed to be printed upright on the plate. You will need 2 center portions to make a full length blade. I have included pegs which should be glued to join all the sections. I suggest thick walls. I print with 5 walls for good measure. Really helps with flex. Use supports for the peg holes. On the restored blade, I did not include a tip since it is the same as the original blade.</li><li>Cross guard - I have sliced this 2 ways: Sideways for more vertical printing. Excellent cooling is a must. I had very slight sagging towards the top of mine due to the sharp angles of the tips. Or sliced in half for a wider print but easier details if bed adhesion and warping isn't an issue. Supports are a must for both. Focus on the interior portions and tips.</li><li>Grip - Simple part. Print with flared portion on the plate. Make sure to glue it with the cutout portion facing forward. Important for the wrap to be aligned with the cross guard.</li><li>Wrap - This is was a trickier part for me since it kept coming loose from the bed. It doesn't have a very wide base so bed adhesion is critical. Supports and brims help. Has a built in peg to lock it into the proper orientation.</li><li>Jewels and Blade surrounds - Super easy print. Glue peg into jewel with inset on the back. Glue surrounds on cross guard.</li><li>Pommel - Two parts for nicer printing. Use grip to help align while gluing halves together. Can remain removable with future upgrades...</li></ul>&nbsp;<h3>Video Demonstration</h3><figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=AtKNojgwpLE"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/AtKNojgwpLE" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Master Sword with interchangeable blades from Legend of Zelda Tears of the Kingdom 

Swords

Sneaker

Bill of Materials with links at the very bottom. Some links are part of an Amazon Associate program, and I may receive compensation from qualifying purchases.&nbsp;Click on "Download raw model files" for the templates.&nbsp;&nbsp;Introducing the Overengineered Filament Closet. The system uses the <a target="_blank" href="https://makerworld.com/en/models/17255#profileId-16014" rel="nofollow noopener">RepRack: Open Source Spool Holder And Storage System by Repkord</a> to hold everything and adds magnetic label holders for 10x3 magnets, InDesign label template, and Excel tracking template.&nbsp;The labels have barcodes, which are scanned using a <a target="_blank" href="https://www.amazon.com/dp/B01GDJ2BH6?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=957c0b080c36884d63ce0e51714a090f&camp=1789&creative=9325" rel="nofollow noopener">cheap Amazon barcode scanner</a> and a <a target="_blank" href="https://www.amazon.com/dp/B07S48NHYS?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=0fdbb07f55688d91b9086270924e5540&camp=1789&creative=9325" rel="nofollow noopener">thermal printer</a> to fit on 2.25" x 1.5" <a target="_blank" href="https://www.amazon.com/dp/B098JHPM3D?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=5d4ad8007d4d51be076c3ac9d4554e67&camp=1789&creative=9325" rel="nofollow noopener">labels</a>. Just click the green Add square and scan. The macro will add an entry to the log and update the quantity in the spreadsheet. The cell will turn red if the quantity goes to 0, but this threshold can be adjusted in the conditional formatting to warn you if you are getting low rather than if you run out.&nbsp;The labels have blank spots to enter additional information, such as flow and CHT information. Each label also has a unique code generated automatically based on brand, material, etc. If you have a brand, color, or material not listed, add it to the legend. ***New zero-lip stl added for cleaner and faster printing!***&nbsp;I used <a target="_blank" href="https://bytescout.com/products/enduser/misc/barcodegenerator.html" rel="nofollow noopener">ByteScout BarCode Generator</a> to batch-create the barcodes. They use Code 128, bar height 50, narrow bar width 3, and no margins. F3D file included for the magnet holder. The room is kept dry using a mid-sized dehumidifier set to turn on and off using an <a target="_blank" href="https://www.amazon.com/dp/B0BNLWT292?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=bf9d1b56dc7dba7bd9656cfc457876c7&camp=1789&creative=9325" rel="nofollow noopener">AC Infinity controller</a> and a <a target="_blank" href="https://www.amazon.com/dp/B0BCHB97Z5?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=c1eadc378caf22914c78da87fe900338&camp=1789&creative=9325" rel="nofollow noopener">control plug</a> set to 20% humidity. A <a target="_blank" href="https://www.amazon.com/Z-Wave-Detector-Carbon-Monoxide-Generation/dp/B08FFB233Y?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=ed9032dc25236812b297228c0954379c&camp=1789&creative=9325" rel="nofollow noopener">smart smoke detector</a> was mounted on the ceiling to be safe. ***Disclaimer*** Some filament is very sensitive to humidity. I have yet to run into any printing problems with TPU, but Nylon needs to be dried before use. Check out <a target="_blank" href="https://makerworld.com/en/models/16523#profileId-15339" rel="nofollow noopener">Chef's Path Single Spool Rod Mount by Sneaker - MakerWorld</a> for a solution for sensitive rolls. The room can sit anywhere between 95 and 105 degrees Fahrenheit with a dehumidifier cycling on and off 24/7. Is this safe? Probably, but maybe not. Replicate at your own risk. I put a smart smoke detector in there so I could get alerts to my phone and smart speakers in the event I couldn't hear it in the closet. Having a dehumidifier run as often as it does uses a lot of power. This setup adds ~$20/mo to my bill.&nbsp;Bill of Materials:&nbsp;Almost everything on here can be found cheaper if you search around. The links included are for convenience only. If you have any questions, don't hesitate to ask!&nbsp;Shelf:Item: <a target="_blank" href="https://www.homedepot.com/p/1-2-in-x-5-ft-Conduit-Electrical-Metallic-Tubing-Steel-0550005000/202068069" rel="nofollow noopener">1/2 in. x 5 ft. Steel Conduit</a> Qty: 2x Shelf Notes: Home Depot / Lowes should be able to cut to size for you, but it only takes a few seconds with a reciprocating saw.&nbsp;Item: <a target="_blank" href="https://www.homedepot.com/p/1-in-x-2-in-x-4-ft-Spruce-Pine-Fir-Common-Board-Actual-Dimensions-0-70-in-x-1-45-in-x-48-in-473436/319661869" rel="nofollow noopener">1 in. x 2 in. (0.75 in. x 1.5 in.)* Common Board</a> Qty: 1x Shelf Notes: The link is just for reference. Almost any type of 1x2 board will work, though I tend to avoid furring strips. *Lumber is sold by its nominal measurement, which is the size before it has been planed smooth. Unless it states otherwise at the store, if the lumber is listed as 1 in. x 2 in., you are buying the right size.&nbsp;Item: <a target="_blank" href="https://www.amazon.com/DEWALT-DW4898-Bi-Metal-Reciprocating-10-Piece/dp/B004TSS2TU?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=3a6ac81d996dddcd4b840297e95bbc96&camp=1789&creative=9325" rel="nofollow noopener">Bi-metal Reciprocating Saw Blade</a> Qty: 1 Notes: You don't need to buy this set, any bi-metal blade will do.&nbsp;Item: <a target="_blank" href="https://www.homedepot.com/p/Grip-Rite-9-x-3-in-Star-Drive-Bugle-Head-Construction-Screw-1-lb-Box-3GCS1/204959258" rel="nofollow noopener">#9 x 3 in. Wood Screws</a> Qty: 1 Notes: This is what I had on hand already. Use whatever you want as long as they anchor deep into the stud.&nbsp;Item: <a target="_blank" href="https://www.amazon.com/DEWALT-DW2535-Piece-Countersink-Assortment/dp/B0000225OU?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=ca8cfc26752eebe43243c5a6c784f05c&camp=1789&creative=9325" rel="nofollow noopener">Countersink drill bits</a> Qty: 1 Notes: Any brand will do.&nbsp;Item: <a target="_blank" href="https://www.amazon.com/dp/B00GDY7IN4?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=72074794668633bc35260f2ea021b32c&camp=1789&creative=9325" rel="nofollow noopener">#6-19, 5/8" Thread Forming/Rolling Screws</a> Qty: 4x Hanger Notes: These lock the clamps to the bar, you could get away with 3x hanger.&nbsp;Item: <a target="_blank" href="https://www.amazon.com/gp/product/B081F6X2W2?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=3491673e7f4751d73646e4397c0490c5&camp=1789&creative=9325" rel="nofollow noopener">Cereal Container Storage</a> Qty: 1x Spool Notes: Only needed for things like Nylon and TPU, and depending on your setup, you might not need them at all. Shelves for the rack can be found here: <a target="_blank" href="https://makerworld.com/en/models/16523#profileId-15339" rel="nofollow noopener">Chef's Path Single Spool Rod Mount by Sneaker - MakerWorld</a> Room:Item: Dehumidifier Qty: 1 Notes: No link because this is going to vary based on your room size and specific needs. I had a refurb one rated for 3,000 sq. ft. that I got on Woot for like $125. If you want to drop below 30%, you need one that is way overkill for the size of the room.&nbsp;Item: <a target="_blank" href="https://www.amazon.com/dp/B0BNLWT292?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=bf9d1b56dc7dba7bd9656cfc457876c7&camp=1789&creative=9325" rel="nofollow noopener">AC Infinity Controller</a> Qty: 1 Notes: This is absolutely not required and much cheaper options are available if you want automation.&nbsp;Item: <a target="_blank" href="https://www.amazon.com/dp/B0BCHB97Z5?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=c1eadc378caf22914c78da87fe900338&camp=1789&creative=9325" rel="nofollow noopener">AC Infinity Control Plug</a> Qty: 1 Notes: To turn the dehumidifier on and off&nbsp;Item: <a target="_blank" href="https://www.amazon.com/Z-Wave-Detector-Carbon-Monoxide-Generation/dp/B08FFB233Y" rel="nofollow noopener">Smart Smoke Detector</a> Qty: 1 Notes: This uses Z-Wave. Get a different smart detector if you don't already have a Z-Wave hub. Labels:Item: <a target="_blank" href="https://www.amazon.com/dp/B01GDJ2BH6?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=957c0b080c36884d63ce0e51714a090f&camp=1789&creative=9325" rel="nofollow noopener">Barcode Scanner</a> Qty: 1 Item: <a target="_blank" href="https://www.amazon.com/dp/B07S48NHYS?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=0fdbb07f55688d91b9086270924e5540&camp=1789&creative=9325" rel="nofollow noopener">Label Printer</a> Qty: 1 Notes: There are a ton of different brands and prices out there. I already had this one so I just bought the correct-sized labels for it.&nbsp;Item:<a target="_blank" href="https://www.amazon.com/dp/B098JHPM3D?&_encoding=UTF8&tag=swiftshapes-20&linkCode=ur2&linkId=5d4ad8007d4d51be076c3ac9d4554e67&camp=1789&creative=9325" rel="nofollow noopener"> 2.25 in. x 1.25 in. Direct Thermal Labels</a> Qty: 1

Overengineered Filament Closet

Storage

Adam L

Note to printables staff : this is NOT a remix of a different model that doesn’t allow remixes, it is an original design of my own making where I invested significant effort. As proof, I am including the Fusion360 CAD files here to prove my design is original from scratch and not a “remix” of that model. It is only a remix of my OWN model. I do respect licenses of others. Note to everyone else: Now includes Fusion360 Model (because reasons.. ) !&nbsp;Some people suggested that they would prefer to use a toothbrush or brass bristle brush to clean their threads instead of the parent <a href="https://www.printables.com/model/476890-super-screw-scrubber-a-sensational-solution-for-sp/remixes" rel="nofollow">Super Screw Scrubber </a>design with paper towel. For them, I've designed this alternative version of the scrubber that lets you slap on a cut-off toothbrush or brass bristle brush or similar and glue it onto the guide. This simple but effective modification lets you get a deeper clean with a longer reach!This version is the more reliable tapered version from the parent that should reduce any first layer print issues. Since the brush bristles are the key to cleaning in this version, the exact tightness of the threads is less important.<h4>Versions</h4><ul><li>DefaultSize (Recommended)</li><li>ShortBrush - if you have a brush that's not quite long enough to comfortably reach, this offers a closer spacing of the flat part to the lead screw by ~ 4 mm. </li></ul>&nbsp;<h3>Print Instructions (same as parent)</h3><ul><li>Print at high layer resolution, I recommend 0.1 or 0.08 if possible on your printer, so that the threads fit nicely. There are slight tolerances built into the thread design so that it should clamp nicely.</li><li>Most filaments should be fine.. but I would avoid anything like carbon fiber or glow in the dark filament to avoid any scratching of the screws (though most are made of steel that probably would not scratch anyways).</li><li>Orient the flat side down. I designed the part slightly asymmetrically so this is intentionally hard to screw up when placing on your bed :).</li></ul><h3>Use instructions </h3><ul><li>Find an old toothbrush or brass bristle brush, cut off the head. Use hot glue (recommended) or some other suitable glue to attach the head to the flat section as shown in the pictures.</li><li>Attach the clamp and brush to your lead screws as shown.. run the bed up and down (make the screws rotate), and hold the clamp in place as you do so.</li><li>Remove the widget, and clean the gunk off (can just rinse with IPA and/or acetone for most greases).</li><li>Re-grease your threads if you stripped all the grease off.</li></ul>&nbsp;<ul><li>Don't use as a regular toothbrush anymore, the ADA has informed me this is not an approved dental product after this modification :). <img src="https://media.printables.com/media/prints/477870/rich_content/50fb1bab-9bd4-4c1c-b9c8-59d26d9d371c/image.png#%7B%22uuid%22%3A%222da5821e-19c2-4860-832f-116d5b83b985%22%2C%22w%22%3A652%2C%22h%22%3A600%7D"></li></ul>&nbsp;3MF & STEP file included!

Super Screw Scrubber: A Sensational Solution for Sparkling Screws (Brushy Edition)

Bambu

Bambu Lab

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014265/design/2023-09-19_8d08d601f168.png"></figure>Let&#39;s start a marble race with friends! This marble run features a series of elements including elevator, starting line, randomized dividers, elevated track, large funnel, spiral, and loop section. It allows competition of multiple marbles, with each segment introducing an element of unpredictability. The excitement continues all the way to the end!&nbsp;Recommended filaments: Bambu PLA series, PLA Basic is recomended for more smooth track<a target="_blank" href="https://store.bambulab.com/collections/bambu-lab-3d-printer-filament?gf_60645=279355719795" rel="nofollow noopener">https://store.bambulab.com/collections/bambu-lab-3d-printer-filament</a>Hardware Kit: Marble Run Components Kit-003<a target="_blank" href="http://store.bambulab.com/products/marble-run-components-kit-003" rel="nofollow noopener">http://store.bambulab.com/products/marble-run-components-kit-003</a>&nbsp;Please make sure you clean the build plate before printing and/or applying glue to prevent print failures.&nbsp;Follow the video tutorial step by step to print and assemble your build. <figure class="media"><div data-oembed-url="https://youtu.be/8_Su9jdzgNA"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/8_Su9jdzgNA" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

Marble Run 003

Toys & Games

BODY3D

Juste a cute Ghost !Print it without supports =)&nbsp;Video : <a href="https://www.tiktok.com/@body3d_/video/7151361561372691717" rel="nofollow">https://www.tiktok.com/@body3d_/video/7151361561372691717</a>

Ghost Booh

Halloween

Overview and goals Flying pegasus is my most sophisticated glider so far. In this project I continue my experiments with single layer wings and stretch this concept to the edge. My goal was to create glider that have build in anhedral angle of the wing without no need to bend them. I achieved that by separated model into part that have to be glued together after print. After seven prototypes I achived quite good glider with decent charasterictic of flights.Assembly After print, first glue together body and then glue wings and tail. I used cyanoacrylate glue (super glue) and bond is very strong. In no one printed version I haven't had no issue with glued part. They kept together even after hard crashes.<figure class="image"><img src="https://media.printables.com/media/prints/427770/rich_content/096f5939-4904-4d36-ae40-f2045c470611/assem.gif"></figure>Flight To fly, just throw glider like paper plane. You can adjust tail by bending it up a little. <figure class="image"><img src="https://media.printables.com/media/prints/427770/rich_content/7e70cc47-3bc8-47d8-8423-abcb39ae22d7/tail.gif"></figure>Balance Different materials have different density so I don't wanted to overdo it with balast of the head. I left there some underweight to calibrate it by yourself. With normal PLA it should working, alternatively you can add some plasticine (about 1.5 g) to head if you need to. Generally you pegasus should stand on his legs, if head will be to heavy and prevails back legs, then you need to decrease balast of the head like below. Good balance without plasticine for moderate throw<figure class="image image-style-align-center"><img src="https://media.printables.com/media/prints/427770/rich_content/c0db615c-fedb-4164-ba73-edd718166885/balans-acceptable.gif"></figure>Maximum balast with plasticine ( in this case 1,5 g) for flight with high force of throw<figure class="image"><img src="https://media.printables.com/media/prints/427770/rich_content/c89229ee-e354-4c41-a778-b9a0d1b7b81a/balans-maks.gif"></figure>&nbsp;You can also check balance by using “hair” hook on the neck. Balance should be achived on second hook.Without plasticine head and back is quite even. In this state pegasus has good flights with moderate force of throw.<figure class="image"><img src="https://media.printables.com/media/prints/427770/rich_content/045e77ae-bed5-401b-97e4-d5b6eba7a0b4/balansokup.gif"></figure>&nbsp;With balast the head is a little below back and this is good for flights with high force of throw.<figure class="image"><img src="https://media.printables.com/media/prints/427770/rich_content/f9dc999a-fbd7-4182-b1bf-63764f3b33bd/balance-maksup.gif"></figure>&nbsp;StandingApart from flight I designed pegasus to be decoration too. You can print it in different colours, using change layer colour option in slicer. YOu can storage it in four different states. 1 Simple standing on his legs 2 Putting its back legs into stand. In this state he looks like it's about to take flight. 3. Standing on its tail, presented wing in all its glory 4 Hung on the hook ( presentend in balance section)<figure class="image image_resized" style="width:455.531px;"><img src="https://media.printables.com/media/prints/427770/rich_content/f040502e-f373-429a-bfa1-bbfa3ff83715/thumbs/cover/800x600/jpg/stand.webp"></figure>&nbsp;FlightsSome examples of flights<figure class="image"><img src="https://media.printables.com/media/prints/427770/rich_content/dcf03817-7ce7-44f8-a34e-5b4ce714a6cd/flight1.gif"></figure>&nbsp;<figure class="image"><img src="https://media.printables.com/media/prints/427770/rich_content/dedfd98a-ae13-461e-83a1-135e4ddc5406/2.webp"></figure><figure class="image"><img src="https://media.printables.com/media/prints/427770/rich_content/3ed9fcae-cba4-41ca-a001-83492a2d377c/3.gif"></figure>

Flying Pegasus

Flying Things

IXPatch

This is a cute little articulated llama 🦙 It can stand on its own and move each leg separately. It is a print-in-place model, requiring no supports or assembly.In addition to the regular single-color version, there is also a multicolor version for Bambu Studio. Enjoy :)

Cute Llama - Flexi Articulated Animal (print-in-place)

Flexi Critters

printchallenge

Print all files. I added different groups so they can be printed in different colors. For assembly instructions please watch this short:&nbsp;<figure class="media"><div data-oembed-url="https://youtube.com/shorts/J7GMYzbBtdc?feature=share"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=J7GMYzbBtdc"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/J7GMYzbBtdc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>

Mini Mars Rover

Cars and Trucks

** Get an early start! Get the <a target="_blank" href="https://makerworld.com/en/models/41177" rel="nofollow noopener">Christmas version</a> now! **&nbsp;&nbsp;Light up different Halloween scenes in this display. A tea light candle is required. The display features a door that opens to allow access to the tea light. Use a section of 1.75mm filament inside the hinge to connect the door to the case. Depending on your printer/setup, this hole may be on the tight side or a bit loose. If tight, drilling out the hole may help. If it is slightly oversized, I suggest melting the end of the filament piece with a soldering iron or lighter.I have included a separate liner. This allows you to print the case in a dark color, but line the inside with a lighter color to allow for more reflection of light outward, making everything brighter.For a complete display, you will need:<ul><li>1x Case</li><li>1x Door</li><li>1x Knob</li><li>1x Snap Ring</li><li>1x Liner - Optional</li><li>1x (minimum) Scene - You can easily remove the snap ring to swap out scenes as desired</li></ul>Check out my other holiday models <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/23941" rel="nofollow noopener">here</a>.<h4>Print Settings</h4>No special setting are needed for the display case, door, knob, snap ring and liner. &nbsp;Scenes Print SettingsPrint the scenes with 100% infill. The scenes also require color changes:<ul><li>The top 2 layers should be black</li><li>If there is no moon in the scene, all other layers can be white or clear - both look nice</li><li>If there is a moon in the scene, it will look best if the bottom 2 layers are printed in clear filament<ul><li>All other layers should be white</li><li>All non-black layers could be printed in all white or all clear if one isn't available to you</li></ul></li></ul>&nbsp;<h4>Assembly</h4>Glue the knob into the door. Only a very small amount is needed.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_njhnxlluv3as.png"></figure>Put the door in place and latch it. Use a 20mm piece of 1.75mm filament to connect the 3 sections of the hinge. If the filament goes in very easily, it may be a good idea to heat up the top end of the filament ‘pin’ and press it flat. This will prevent the pin from falling through later on.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_ps9jc73zrxio.png"></figure>Open the door. Insert a scene into the opening (image facing outward). Insert the snap ring behind the scene by gently squeezing and placing it into the groove (see red arrow below).<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_zosx4sj7pb0v.png"></figure>If you are using a liner, slide it inside the case. This may be a tight fit. Go slowly and be sure to slide it in evenly on all sides.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_t3jeg8v9f9hv.png"></figure>Turn on your tea light and close the door.&nbsp;&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Bambu Lab Matte Charcoal PLA</li><li>Bambu Lab Matte Ivory White PLA</li><li>GIANTARM Transparent Clear PLA</li></ul>