maxpowerz

LoboCNC

<figure class="media"><div data-oembed-url="https://youtu.be/3CzV9iwZRQc"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/3CzV9iwZRQc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>With this 21 shot rubber band shooter, you'll be able to rain hellfire (hell rubber?) down on your competition. This is a completely redesigned version of my <a target="_blank" href="https://makerworld.com/en/models/95135" rel="nofollow noopener">earlier rubber band shooter</a> with a vastly simpler trigger and indexing mechanism, and more stretch for longer shots.&nbsp;The mechanism uses a pawl and ratchet for turning a worm gear that both advances the magazine and releases each band. Pulling the trigger causes the worm ¼ turn, advancing the magazine by one tooth. The leading edge of each of the 4 threads on the worm is what pushes each rubber band off of the nub above each tooth gap.&nbsp;Assembly<ol><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_487e03e1072d6.jpg"> Remove the small built-in support that sits in the trigger slot.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_affbef958b134.jpg"> Insert the trigger into the slot  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_3180e31dfd26.jpg"> Slide the U-shaped clip over into the notches in the trigger to hold it in place.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_a5eb3274b4a56.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_baca0d09c4d03.jpg"> Slide the pawl into the slot at the back of the shooter and place the hole in the end of the pawl onto the post on the trigger.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_8fad8a27fedeb.jpg"> Screw the worm onto the back end ot the shooter with one of the screws.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_a5a8995ebfeae.jpg"> Hook a small rubber band between the hook on the trigger and the hook on the frame.  </li><li><img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_5bed8080ce354.jpg"> Screw the tip of the magazine into the front end of the shooter with the second screw.  </li></ol>Play You are now ready to load the rubber bands. The stretched length of the bands is about 280 mm and you can use any 1.5-3mm wide bands that will stretch that far.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_dbb06ff5acfb8.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_64708c74cef49.jpg"> <img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_722e3012b36f9.jpg"> Start at the right side of the magazine. Loop one end of the band over the nose of the magazine and then hook the other end over the little nub above the gear-tooth gap. The 3rd photo shows how it looks as you progress.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/477630/2024-01-28_07e79f6f6406b.jpg"> Now pivot the magazine around so that the left-most tooth engages the worm. Each pull of the trigger should advance the magazine one tooth and release one rubber band.

21-Shot Rubber Band Shooter

Toys

HangarDesigns

Cincinnati Bengals floating logo sign. THIS IS A MULTI-PART LOGO, that means it does not require an AMS! This is so the texture of the textured plate will be on the front of all the parts of the sign and to help achieve a 3 dimensional look as all the colors are different thicknesses. The different components (if large enough) are modeled with connecting pins to achieve a press fit, but a bit of CA glue doesn't hurt (ProTip- if CA glue cures without an accelerator, it may leave a smoky residue. If you apply a thin coat of WD-40 and wipe away, this residue will disappear).&nbsp;The base is modeled with an integrated hangar and standoff feet.&nbsp;The holes in the logo and base are designed to accept TPU adapters that allow the acrylic rods (with slight manufacturing diameter deviations) to be installed and removed easily, while remaining secure. These adapters can be found here- <a target="_blank" href="https://makerworld.com/en/models/39229#profileId-38178" rel="nofollow noopener">https://makerworld.com/en/models/39229#profileId-38178</a> . The inserts are designed with a 2 degree draft angle to lock them in place once installed. I generally print these in clear TPU or a matching color TPU if I have it. I included the F3D file in case you want to change the design to fit any dowel you may have (or print). The dowels I use- <a target="_blank" href="https://www.amazon.com/dp/B09SKYYS5X?psc=1&ref=ppx_yo2ov_dt_b_product_details." rel="nofollow noopener">https://www.amazon.com/dp/B09SKYYS5X?psc=1&ref=ppx_yo2ov_dt_b_product_details.</a>&nbsp;If you like this design, think about buying me a coffee (let's be honest- it's going towards filament)- https://www.buymeacoffee.com/thehangardesigns

NFL Cincinnati Bengals Floating Logo Sign

Signs

Maty505

better articulated dragon. be careful when scaling down cause the tail can breake at smaller sizez. scaling up is fine.

Toys

Signs

Duplo

tools and organization