Matthew

Darrare

A prop/cosplay sword and sheath that holds a standard dice set for D&D. I printed a bunch of these out for friends for Christmas or birthday gifts super easily, only very minor supports needed.&nbsp;The hilt and blade have some nubs that interlock, but what I did was I used the hot end of my hot glue gun to melt the nubs and melt a bit in the hilt to create an uneven surface to let the hot glue really hold with a strong bond. I also just tried plain super glue and it held really well, but not as sturdy as the hot glue gun method.

Dice Holder for D&D Dice Set

Gaming

EPIQ3D

Make All your herbs easy in the kitchen.This planter ensures that your herbs stay fresh and hydrated.&nbsp;<figure class="image image_resized" style="width:84.24%;"><img src="https://makerworld.bblmw.com/makerworld/draft/836596/2024-04-09_ede14bf23669e.png"></figure>&nbsp;<h3>HOW IT WORKS</h3>The self watering planter is designed to slowly absorb water from the reservoir (This needs to be filled up occasionally).Its a one piece print (uni body).&nbsp;<figure class="image image_resized" style="width:84%;"><img src="https://makerworld.bblmw.com/makerworld/draft/836596/2024-04-09_2bdf03c8c5f73.png"></figure>&nbsp;The water inlet, is alongside the upper part, and is guided down to the reservoir. This also acts like a overflow, so you dont overfill the reservoir. (Stop filling in water, when is reaches the edge, or when it pours over - you decide)&nbsp;It is recommended to use a wicking material at the center (between the soil and the water).This helps to absorb water into the soil slowly. You can place a couple of cotton balls / cotton wool in the bottom of the pot.I recommend filling wicking material so it is above the reservoir edge, then fill with soil, and your herb of choice.&nbsp;&nbsp;Basic print settings:<ul><li>Infill : 10%</li><li>Walls: 3</li><li>Top/bottom shell layers: 3</li><li>No support needed</li></ul>Dimensions: hight 70mm, Crossection: 74mm (at the widest point)

Self watering herb/flower pot

For crystal

iLab 3D

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm - 1 loopFilaments Used: SUNLU Black Transmission Distance: 0.3 SUNLU Gray Transmission Distance: 2.5 PLA BambuLab Basic Beige Transmission Distance: 8 SUNLU White Transmission Distance: 6&nbsp;Swap Instructions: Start with Black At layer #7 (0.64mm) swap to Gray At layer #14 (1.2mm) swap to Beige At layer #20 (1.68mm) swap to White for the rest.

Dragon - HueForge

For Me

TsiTsi

2020 Aluminum Extrusion - Scale As needed.

2020 Aluminum Extrusion

Engineering

mail.iou

Collapsing Katana 天鎖斬月 (BLEACH -Tensa Zangetsu)This is a telescopic sword inspired by the sword "天鎖斬月" used by Kurosaki Ichigo in the Japanese manga "BLEACH". This is a telescopic katana that is printed in parts and then assembled. You can choose to print different colors and strengths for different parts. The handle is capped to facilitate future maintenance and blade replacement.However, the disadvantage of this is that the printing time will increase. If you are sure that you can print an all-in-one print, you can refer to my previous telescopic knife work Reverse Blade Sword mini: https://makerworld.com/en/models/114630&nbsp;Notice It is recommended to use PLA+、PETG for printing. If your filament has insufficient strength, please increase the fill overlap to more than 40%.&nbsp;Assembly instructions: 1. Place the blades in order.2. Close the handle cover.<img src="https://makerworld.bblmw.com/makerworld/draft/669172/2024-03-09_3962f81c0b1a2.png">&nbsp;3. Insert two pins to secure.<figure class="table"><table><tbody><tr><td><img src="https://makerworld.bblmw.com/makerworld/draft/669172/2024-03-09_49b8dafec3343.png"></td><td><img src="https://makerworld.bblmw.com/makerworld/draft/669172/2024-03-09_d90619ba279ab.png"></td></tr></tbody></table></figure>&nbsp;4. fixation of chains Glue is required to secure the chain to the cover of the handle.<img src="https://makerworld.bblmw.com/makerworld/draft/669172/2024-03-09_851405b7d869e.png">&nbsp;Remark: 1. If the pin is too loose, you can apply removable glue, such as Styrofoam, to the tip of the latch to facilitate removal during future repairs. 2. Since the flow rate of each brand of filament will vary, the pin may be too thick or too thin. If you encounter this problem, you can adjust the Z height of the pin and print the two pin parts separately. 3. If it is difficult to align the exit hole when the pin is inserted into the tool holder, you can use a blade to push in the direction of the hole to facilitate alignment of the exit hole.<figure class="table"><table><tbody><tr><td><img src="https://makerworld.bblmw.com/makerworld/draft/669172/2024-02-24_383d366365265.png"></td><td><figure class="image image_resized" style="width:100%;"><img src="https://makerworld.bblmw.com/makerworld/draft/669172/2024-02-24_08d21962ae4eb.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/669172/2024-02-24_4f45d2e261b7f.png"></figure></td></tr></tbody></table></figure>&nbsp;&nbsp;

Collapsing Katana 天鎖斬月 (BLEACH -Tensa Zangetsu)

For the kids

Maoirae

Made some addition for my spool shelf design, filament material tags so you can separate different type of filaments from each other on one shelf and not mixing them accidentaly. Tags are just clip on, no additionl hardware required.&nbsp;This fits my spool shelf here with all different dimension wooden dowels, 20mm, 23mm and as well 1inch: <a target="_blank" href="https://makerworld.com/en/models/88779#profileId-95016" rel="nofollow noopener">https://makerworld.com/en/models/88779#profileId-95016</a>&nbsp;Also added multicolor version.&nbsp;Added some more tags, now it contain: PLA, ABS, ASA, PETG, NYLON, TPU, CARBON, GLOW, FLEXI, CLEANER, MARBLE, MATTE, SILK.Also added blank tag so you can add custom text as you want.&nbsp;If you need tags with different text, just let me know :)

Gaming

For crystal

For Me

Engineering

For the kids

Printer Upgrades