mattdeogracias

Boink

fits a 22&#34; headMagnets 9x2mm for the standard profile 10x2mm for the enlarged one. Don&#39;t apply too much pressure and crack the mask if the magnets feel too snug. If the magnet hole is a bit small, then use a lighter or soldering iron to loosen the hole. I also use a drop of super glue for each magnet to ensure they stick.

Ironman Mark 46-47 Helmet (wearable with magnets)

helmets

SavageLau

&nbsp;This simple tool is fast to print, and cost very little filaments, 1.95g each.This tool will help you lube on the z and y axis (lead screw and linear rod).Extended length handle will help you easy to reach center one that within the cover.You can control the angle to push how much lube apply to the screw.<figure class="image image_resized" style="width:78.49%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_10731b083ab3.gif"></figure>&nbsp;<h3>Leadscrew:</h3><figure class="image image_resized" style="width:77.49%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_047b690a0cf77.jpg"></figure><figure class="image image_resized" style="width:77%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_0136c09e64bc8.jpg"></figure><h3>Linear rods:</h3><figure class="image image_resized" style="width:76.74%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_25301222a7901.jpg"></figure><figure class="image image_resized" style="width:76.18%;"><img src="https://makerworld.bblmw.com/makerworld/draft/368109/2023-12-19_6dbff3848e74c.jpg"></figure>

P & X Series Lube helper

Tools

OwenTF

This is a toy Butterfly Knife / Balisong I designed. No metal hardware such as screws or bolts are needed.&nbsp;Check out my new Banana Switchblade <a target="_blank" href="https://makerworld.com/en/models/480959#profileId-392609" rel="nofollow noopener">here.</a>&nbsp;You can find my other toy knife designs <a target="_blank" href="https://makerworld.com/en/@OwenTF/collections/608169" rel="nofollow noopener">here.</a>&nbsp;You can obtain a commercial license to sell prints of this <a target="_blank" href="https://www.printables.com/@OwenTF_1791221#join:894" rel="nofollow noopener">here</a>.<h3>Print Settings</h3>Resolution:0.1 mmInfill:100%  Notes:This is designed with very tight tolerances so print quality is very important. Two slicer settings that I would recommend tweaking are print resolution (smaller is better) and outer wall speed (20 mm/s is good). If your still having problems with the screw tolerances you can try shrinking them in the x and y directions.Assembly InstructionsThe first step for assembly is to separate the handles and blade from their bases. Firmly grip the base and snap it off. Next, use small pliers to remove the supports from the pin holes at the top of the handles and bottom of the blade. File down any material left in the pin holes from the supports. I recommend using a small circular file but a knife would also work. The blade pins should have a very loose fit with the blade and a tight fit with the handles. Also check the fit between the blade and the handles. If it is too tight and does not rotate smoothly, file down the inside surfaces of the handles until it rotates smoothly. Once everything fits together smoothly, use a flat head screwdriver to screw the pins in place. I would also recommend applying a plastic lubricant on all contact surfaces.&nbsp;Image of all the parts before supports are removed.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000185549/design/2024-02-14_phg1bji34tfs.jpg"></figure>&nbsp;This video shows what each part should look after the supports have been removed. It also shows how to assemble them.<a target="_blank" href="https://youtu.be/wXwBjPturD0?feature=shared" rel="nofollow noopener">https://youtu.be/wXwBjPturD0?feature=shared</a>&nbsp;This is an image of how it should look after being assembled.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000185549/design/2024-02-14_3ixhc3mlxziu.jpg"></figure>

Toy Butterfly Knife (No Hardware Needed)

Swords

WorkShop3D

Hi everyone! I&#39;m sharing my first keychain that I made for my girlfriend. Planning on releasing the rest of the Sanrio family soon! the keychain printed really nice on my P1S and took around 30min. If you enjoy the file, feel free to rate it 5*!

helmets

Tools

Swords

Key Chains