marco08108

mail.iou

update 04/05/2024If you want a printing method that is easy to maintain, you can consider my redesign:Reverse Blade Collapsing Katana - Rurouni Kenshin<a target="_blank" href="https://makerworld.com/en/models/414234" rel="nofollow noopener">https://makerworld.com/en/models/414234</a>&nbsp;update 01/12/2024 This knife is a one-piece printed design. If you are not sure whether the filament you bought can print this work well, you can refer to my new creation &#34;Nichirin Samurai Sword&#34;. This work uses a split printing design to facilitate future maintenance and blade replacement. Nichirin Samurai Sword : <a target="_blank" href="https://makerworld.com/en/models/135353" rel="nofollow noopener">https://makerworld.com/en/models/135353</a>&nbsp;Reverse Blade Sword miniThis is a smaller version of the Reverse Blade Sword, with a total length of about 80cm, suitable for A1 mini printers or people who don’t want to print too much. If you want to experience the full size, please go to <a target="_blank" href="https://makerworld.com/en/models/111322" rel="nofollow noopener">https://makerworld.com/en/models/111322</a>&nbsp;Notice It is recommended to use PLA+ and Textured PEI Plate for printing. If the viscosity of the plate of your 3D printer deteriorates, be sure to use glue to increase the grip to prevent the printed part from falling off halfway and wasting filament.After printing, please remove the support at the end of the knife.<figure class="table" style="width:77.33%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-29_51c8c09c32f62.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-29_60e68ce20b26b.png"></figure></td></tr></tbody></table></figure>Repair of fallen blades This work has been printed and verified on P1S, A1, and A1 mini printers and resized. It is currently tested using three materials: Bambu PLA, eSUN PLA+, and eSUN ePLA-Matte. The blade surface can be freely expanded and contracted without falling off. However, since PLA material is not resistant to high temperatures, if it is stretched and swung back and forth many times quickly, it will cause the blade to be heated and expand, causing the blade to be thrown out. At this time, you can repair it with a simple method. Please use a tape with high viscosity that is not easy to fall off, such as Acetate Cloth Tape. Stick it on the entrance where the blade falls off. The amount of tape can be adjusted to increase or decrease the size of the enlarged hole. Then push the blade down and plug it back into the entrance to repair it.<figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-30_59e2edca56a86.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-30_9ae8cbf98f5af.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-30_75ce6d29cda6e.png"></figure></td></tr></tbody></table></figure>&nbsp;&nbsp;

Reverse Blade Sword mini ( Samurai Sword)

codehustler

Its a modular formicarium, aka ant farm. For small ants.Nests and arenas can be conneted in multiple ways. Attach more space when your colony grows. Open and close the doors between the habitats.Use 2mm acrylic glas to cover the habitats.Included a drill jig to help you cut out and drill holes into the acrylic glas covers.Print out the hinges to connect the arenas and nests and put a door between them.close all open end tunnels with door plugs.there are two nests. a "dry" nest and a "wet" nest. the "wet" nest has a big center cylinder to store water and distribute it to one corner and two opensings arround the clinder. add some soil, clay or gypsum to cover the water outlets. The water will keep the material moist.

Modular Formicarium // Ant Farm

laisch

With this handy little tool you can clean your carbon rods even when the lid of your bambulab printer is closed.Just put Isopropyl alcohol on the sponges, snap it to your carbon rod and move it back and forth a few times till they are shiny again.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/251911/2023-12-07_e4ey6ohuzxon.gif"></figure>&nbsp;<h3>Postprocessing</h3>For the sponges you can use a normal kitchen sponge (be careful to not use the abrasive ones). Cut two pieces roughly about 10x20x20mm and press them into the spongeholder.For the pullback mechanism you can either print the provided spring in TPU, or use small hair rubberbands. The spring also works in PETG but looses its strength from time to time.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/251911/2023-12-07_g1k0c2tnzlwn.jpg"></figure>&nbsp;&nbsp;More info about cleaning the carbon rods can be found in the <a target="_blank" href="https://wiki.bambulab.com/en/general/carbon-rods-clearance" rel="nofollow noopener">Bambulab Wiki</a>

Toy

Ant

Tools