marckau

michelem

Welcome to our cozy Midcentury Modern Birdhouse!&nbsp;It&#39;s not just a home for birds – it&#39;s a stylish retreat full of cool features like a Wifi enabled camera for birdwatching and more!&nbsp;Around the house, you&#39;ll find cool stuff like a modern textured panel, tiny cacti, a cute wooden-effect wall, a pergola for shade and a handy tray for seeds or plants. There&#39;s even a pop of color with a fun angular piece!&nbsp;Of course, there&#39;s a 35mm entrance and a little perch for our feathered friends.&nbsp;But the coolest part? The roof has a big opening covered by a magnetic box that looks like a mini terrace. It&#39;s not just for looks – you can put a plant in it with the &#34;Terrace Box&#34; component or add a WiFi camera with the &#34;Blink Support&#34; part to see what the birds are up to!&nbsp;It comes with mounts for walls or poles, so you can place it wherever you like.&nbsp;Printing it is easy but takes a bit of time. Since it&#39;s for outdoors, use tough materials like PETG, ABS, or ASA is recommended. PLA might fade or warp in the sun.&nbsp;You&#39;ll need screws, bolts, inserts, and magnets – check the list below for everything you need!&nbsp;Assembling it is quite intuitive, but I have attached the complete instructions.&nbsp;To add the Wifi camera you will need a Blink device (works with Blink Outdoor 3 or 4). You could need also the Sync Module or an Alexa device to connect the camera to.&nbsp;I personally used these:&nbsp;<a target="_blank" href="https://www.amazon.it/dp/B086DKRWCH?psc=1&amp;ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">Blink Outdoor Camera</a> <a target="_blank" href="https://www.amazon.it/dp/B084RPZGR2?psc=1&amp;ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">Blink Sync Module</a>&nbsp;NOTE:It&#39;s recommended not to install the birdhouse in direct sunlight, especially if equipped with the WiFi camera. Best place would be under a tree or similar.&nbsp;Dimensions&nbsp;The base is 25cm x 20cm. The house with terrace is tall about 19cm max.&nbsp;Unfortunately, I&#39;ve just finished and mounted the first one, so I don&#39;t have any videos of our little friends to show you yet. However, here&#39;s a peek inside with the camera:&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000468694/design/2024-05-19_c9dc902e65eab.jpeg"></figure>Get ready to enjoy building your birdhouse and making new feathered friends!

Modern Midcentury Birdhouse - Wifi Camera enabled

school

Printerchen

<h3>About the design</h3>I designed my own 180° Uphill Track that fixes two issues I had with the track from Cannela Verde: The Angle is wider, so the trains, even three-axle trains, fit better on the track, even electric trains are able to climb the slope. The second fixed issue: the height is now compatible to Brio bridges.To achieve that I split the track into two parts, so they will fit on my printers bed. The parts can be easily plugged together and also separated again after playing (for better storing).&nbsp;There is also a <a target="_blank" href="https://makerworld.com/en/models/79423" rel="nofollow noopener">2 Part Version</a> (which is shown on the photos).<h3> Printing</h3>I recommend to print it in at least 0,16mm to have a smooth surface on the top. You can combine the infill and select "adaptive cubic" as Infill pattern to save time and material.<h3> See the track in action</h3><figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=X3NvCDvwuzI"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/X3NvCDvwuzI" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

180° Brio Uphill Track (3 Parts)

brio

TerTerro

Traffic Signs to use with Brio/Ikea/Hot Wheels or other games. Designed to not need AMS, 1cm thick and 0.56mm thick top color later. Print in white and change color on top two layers. Print in 0.28 layer height. For base add modifier to have infill 50%, rest is 10% infill fine. Added print profiles with these settings. If you have wishes for other traffic signs, let me know, I see what I can do :)

Traffic Signs for Brio/Ikea/Hot Wheels and other toys

OddPlasticity

You might also like to check out my Halloween Ghost Cat Trio, <a target="_blank" href="https://makerworld.com/en/models/30639#profileId-27171" rel="nofollow noopener">which you can find here</a>. &nbsp;Three happy ghost dogs waiting to share Halloween with you. My brother once owned an old German Shepherd who always had an enormous bone hanging from his mouth. The “dog with bone” model in this collection is inspired by that friendly old beast. &nbsp;If you like these models, it'd mean so much to me <a target="_blank" href="https://www.buymeacoffee.com/mlambertfrw" rel="nofollow noopener">if you buy me a coffee</a>. &nbsp;Happy Halloween!&nbsp;&nbsp;

Halloween Ghost Dog Trio

holiday 

bensbigolbeard

<h2>An Icosahedron made of bevel gears.</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461626/2023-10-04_58621e1768a8e.gif"></figure>&nbsp;<h3>Assembly</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461626/2024-01-27_56dec3bf3a3588.gif"></figure><h3>Text Assembly Instructions:</h3>Some folks have had trouble following the video above (sry, it's not as clear as I'd hoped), so here are some alternate instructions. The image shows the process, working from top left to bottom right.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/461626/2023-10-22_97301cb6256.png"></figure>Image 1<ul><li>The first image above shows two large gears attached to the core, with one small gear in between them.</li><li>Point the larger gears' pointed teeth straight up (i just took the pin out on the opposite side, so it could sit flat for the pic). These points are indicated in red in the image.</li><li>Looking at the small gear, locate the three sides of the small triangle on the back and make sure that the insets (indicated with red “V”s in the image) are angled to accept the larger gears' pointed teeth.</li><li>You should then be able to add the next large gear with the point up, like you see in the first image.</li></ul>Image 2<ul><li>The second image shows the model flipped over 180 degrees, sitting on flat of the small gear that was just on top</li><li>Stick on the last large gear to the pin pointed up (it can be in any orientation at first)</li></ul>Image 3<ul><li>Find an empty gear slot and point it upwards.</li><li>Orient the large gears so the points are now pointing up around the empty small gear slot, similar to their orientation in the first image.</li><li>Pop in the small gear, with those triangle corner inset areas accepting the large gears' points</li></ul>Image 4<ul><li>repeat the previous step until all of the empty small-gear slots are file</li></ul>That should leave you with everything in the correct arrangement! The pins will fully seat after the initial turns, so you might hear them pop into place. If you still encounter issues, I'm active in the comments and would be happy to help troubleshoot.&nbsp;Background: I love <a target="_blank" href="https://www.printables.com/model/245028-three-cube-gears" rel="nofollow noopener">this gear cube</a> and it made me want to explore how to apply that approach to other platonic solids. For some stupid reason I picked the Icosahedron and the additional geometric complexity kicked my butt days. It would have probably been easier if I could math good, but that's not the case… I still prefer how much the gear cube deforms so significantly in it's intermediate states, but the icosahedron is still a satisfying fidget. I might explore some alternative ways to break up the shape to introduce some more deformation, while retaining the smooth gearing. Printing notes:<ul><li>If the gears begin to get loose, replacing the pins with newly printed ones will likely tighten it right up.</li><li>To that end, printing the pins in a more friction resistant material and adding a bit of grease/lubrication can extend their life</li></ul>Print profile updates (for the ones I've uploaded): 10/8/23:<ul><li>Print order changed to outer/inner/infill for better dimensional accuracy</li><li>Brim added to pins for improved bed adhesion for most plate types</li><li>New pins only profile, in case you still have bed adhesion issues or need a fresh set, if the originals wear out</li></ul>10/22/23:<ul><li>I updated the stand-alone STL and 3mf files to include the brim and orientation tweaks from the previous update</li></ul>

Icosahedron Gears Fidget Toy

Fidget 

Adam L

Update 1/28/24:  Added a new version with 90 degree-increment tactile and visual marking in the model, if you prefer to measure your turns by quarter or larger turns.  See “BambuBedBuddy_90DegreeMarks.3mf” if you want these ribbings that indicate how much you&#39;ve turned. Picture:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000015546/design/2024-01-27_a5b6d9c2c3d978.png">&nbsp;Bambu Bed Buddy is a printable wrench that helps you tram/level the bed of your BambuLab printer with the gantry/printhead. It is compatible with all BambuLab models as far as I know, and it can improve the quality and consistency of your prints.Bambu Bed Buddy lets you turn the 3 screws under the bed as part of the <a target="_blank" href="https://wiki.bambulab.com/en/x1/manual/manual-bed-leveling" rel="nofollow noopener">official bambu tramming procedure here</a>, but without destroying your thumbs! The 12-sided knobs under the bed are very tight by design, which makes them a little tricky to fine-tune without a tool. After getting very frustrated with doing this and hurting my thumbs, I designed this tool to help. I hope this helps others!Additionally, it is important to note that the tightening procedure needs to be started all over again if you fail to complete it in the first 3 passes! The key part is that this requires starting with the knobs from a very tight “neutral” position, so that you don&#39;t end up with them too loose. This is pretty annoying, and needed to be fixed.Part of the problem is that Bambu&#39;s provided GCODE file only iterates 3 times and (especially if you&#39;re not using the wrench here!) gives you not enough time to adjust and fine-tune the knobs. To fix this second problem, I simply extended the number of repeats in the included GCODE file here so that it will repeat the 15-second-per-spot sequence for 30 minutes, which should provide ample time for even the most OCD tuners :). I recommend trying to use this file to save on frustration instead of the Bambu one, but the wrench will of course work either way.Shown here printed in Prusament Galaxy Black PLA, 4 walls, 0.2 layer height. The resulting fit is tapered slightly, but will be tight to aid in minimal backlash. If you want to check for fit first to see if you need scaling, I&#39;ve included a small test print. Print the wrench and test piece with the socket of the wrench facing UP (away from the bed).&nbsp;

Bambu Bed Buddy: A wrench to save your fingers

calibration 

Willi 3D

Create your BaBo organizer! A system created to store them all!&nbsp;Description:This is the BaBo drawer module 30. The drawer module is the heart of the system as it carries the inserts and is therefore the main page of the system.&nbsp;The usable dimensions of the drawer are 240x210x30. The drawer has space for 8x7 inserts. The inserts have a grid of 30x30mm, this means a 1x2 insert has the dimensions 30x60mm.&nbsp;BaBo organizer is a stationary, very flexible system to store your tools, spare parts and even printing plates. The design is based on the iconic look of the Bambu Lab X1 printer.&nbsp;It was important to me that even newbies could print and use the system, which is why all parts are printed without support and the parts are already pre-sliced.&nbsp;Furthermore, all inserts for the accessories and tools that the printer comes with are free. Only the special modules and inserts are only accessible to members of my club. The purpose of the club is to promote my work and to reduce the costs that I incur. I would also like to find people who are interested in expanding this system.&nbsp;The entire system uses only 1 type of screw, M3x8 countersunk screws.Links:<ul><li><a target="_blank" href="https://makerworld.com/de/u/24485025/collections/12914" rel="nofollow noopener">BaBo collection</a></li><li><a target="_blank" href="https://makerworld.com/en/u/24485025/collections/666853" rel="nofollow noopener">BaBo duo collection</a></li><li><a target="_blank" href="https://makerworld.com/en/u/24485025/collections/666866" rel="nofollow noopener">BaBo inserts</a></li><li><a target="_blank" href="https://www.printables.com/@Willi/store" rel="nofollow noopener">Exclusive models, printables. (Credit card)</a></li><li><a target="_blank" href="https://than.gs/u/1578655?plans=true" rel="nofollow noopener">Exclusive models, thangs. (Paypal, Credit card)</a></li></ul>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014125/design/2023-09-20_95fdae0c8d181.jpg"></figure>Update:(13/09/23)<ul><li>Assembly optimizations</li></ul>(31/10/23)<ul><li>improved connection between modules</li><li>easier to push back the drawer</li><li>print profile optimizations</li></ul>(26/01/24)<ul><li>design optimizations to prevent warping</li></ul>&nbsp;Printing:Layer height: 0.2Supports: NoBrim: NoMaterial: all&nbsp;Assembly:Follow the instructions in the picture.<ul><li>printed parts</li><li>16 x M3x8 countersunk screws.</li></ul>If you like this model, please throw me a like. Designing the models is time, filament and coffee consuming. <a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=WGL5LXN5EHEXN" rel="nofollow noopener">If you want to support my work buy me a coffee (PayPal).</a> Thanks!&nbsp;Clubcontent:<figure class="image"><a href="https://www.printables.com/@Willi/store" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014125/design/2024-06-13_ccadb89c071b7.jpg"></a></figure><figure class="image"><a href="https://www.printables.com/@Willi/store" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000014125/design/2024-06-13_c05e6d1cbb9c7.jpg"></a></figure>

[BaBo] organizer drawer module 30

make

planpa3d

Designed these Christmas lights to be illuminated with LED tea candles I picked up from amazon.<a href="https://www.amazon.com/gp/product/B09B1371C4/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&th=1" rel="nofollow">https://www.amazon.com/gp/product/B09B1371C4/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&th=1</a>&nbsp;I designed the bulb to be printed out in Vase Mode, or Spiralize outer contour in CURA.I set the layer height to 0.2mm, and set 5 bottom layers.&nbsp;The other parts for either the small or large can be printed without supports.&nbsp;The base for the small bulb is supper simple and has a threaded cover when the LED candle is inserted.The large bulb base has a cover that can be added to store a 2nd LED candle. I use 8mm x 3mm magnets to secure the base cover to the base. The large bulb snaps onto its base just fine covering the LED.The small bulb will need glued onto its base.You can follow me on instagram, <a href="https://www.instagram.com/pla.n.pa/" rel="nofollow">https://www.instagram.com/pla.n.pa/</a> to find out what I designs I am currently working onIf your interested in selling prints of my designs, become a Patreon supporter here… <a href="https://patreon.com/planpa3d" rel="nofollow">https://patreon.com/planpa3d</a>Thanks for checking out my design, and Happy printing!!

XMAS LIGHT LED CANDLES

light

Chris Pirillo

Darth Vader loves watching sunrises (and sunsets). Hates long walks on the beach, however.&nbsp;In the early morning hours, before the galaxy awoke, Vader would venture to a secluded spot on a remote planet, far from the prying eyes of the Empire. As the first rays of sunlight pierced the horizon, he would watch as darkness gave way to a kaleidoscope of hues. The vibrant oranges, pinks, and purples painted the sky, and for a brief moment, Vader could almost forget the weight of his responsibilities.&nbsp;Similarly, in the evening, after a grueling day of commanding his forces, Vader would retreat to the privacy of his meditation chamber. With its dimly lit ambiance, he would take a moment to reflect as the sun dipped below the horizon. The colors shifted and deepened, casting a soft glow that mirrored the turmoil and conflict within him. It was during these sunsets that Vader allowed himself a glimpse of the person he once was, before he became consumed by the darkness.&nbsp;In these quiet moments, Darth Vader found solace and a connection to a world beyond his own. The sunrises and sunsets reminded him of the beauty that still existed in the universe, even amidst the chaos and destruction. They were a reminder of the light he had lost and the possibility of redemption, however distant it may seem. And as he stood there, entranced by the shifting sky, a flicker of hope ignited within the dark heart of Darth Vader.&nbsp;Image prompted in MidJourney, prepped in HueForge.&nbsp;I sliced this at a .08mm layer height.<ul><li>Black to layer 7</li><li>Red to layer 14</li><li>Orange to layer 22</li><li>Yellow to layer 39</li></ul>

Star Wars (Inspired) "Sith Sunset to Sunrise" HueForge Darth Vader

Amao Chan

<div><h1>Summary</h1><div>Pangolins now are facing critical crisis as they are closing to extinct. In fact, humans are the murderers of this disaster, superstition and greed are the main reason to cause this massacre. Pangolins, the mammals covered in tough and overlapping scales, are actually far from aggressive. Their scales provide good defense against predators in wild. However, they’re considered the world’s most hunted animal because people believe that the meat is prized for medicinal ingredient and the scales help curl impotence. Nowadays, the numbers of pangolins are less and less, some people eat them only for the reason of showing their ostentatious wealth, what they do to these helpless animals is to make them approach to endangered. Although International trade in pangolins has been banned by CITES since 2000; and are listed them as 'protected species' in most Asian home states, scaly anteaters are still threaten with smuggling and poaching. Pangolins’ disappear would not be the result we expect to see, only when strictly implement of law enforcement on punishing these poachers and pangolin-eaters would effectively bring down the crisis of extinction. This is our latest chance to save pangolins, and please never make science predictions come true. Pangolin is a really skillful and difficult work that I have spent a lot of time on it. It has been passed at least six editions before presenting to all of you. What I was trying to challenge is an artwork with both perfect appearance and function. It was a little struggle for me to share this work at the beginning since I’ve fallen in love with it when it’s first done and stood in front of me. At this moment, what I am wondering more is to let you firsthand it, holding and feeling the variation with actions. Enjoy and I believe you’ll like it. Same file will be uploaded to <a href="http://fastlab.tw/" rel="nofollow">http://fastlab.tw/</a>, (Institute for Information Industry, III), which is a 3D works sharing website, welcome all 3D players upload your works and have fun here! Special thanks to Shinkong Synthetic Fibers Corp. for providing dedicated color materials (ABS) and supporting on this creation.Design Software - SketchUp my settings ABS z resolution 0.2mm scale 100% Don't printing all models are small then 75% of original model size, and set up 0.15mm layer resolution.<a href="https://amaochan.work/" rel="nofollow">https://amaochan.work/</a> <a href="https://www.facebook.com/paperworkers" rel="nofollow">https://www.facebook.com/paperworkers</a> <a href="https://www.youtube.com/watch?v=fkWxOLbFxPI" rel="nofollow">https://www.youtube.com/watch?v=fkWxOLbFxPI</a><hr>穿山甲正面臨迫切的危機，牠們走在快速滅絕道路上，人類是這場災難的兇手，迷信與貪婪是屠殺的原因。穿山甲這個性情溫和的動物，全身佈滿鱗片，這些鱗片在野外對於保護自己有些幫助，但是身上的鱗片也是牠們被獵殺的因素。因迷信穿山甲的鱗片有醫療與壯陽的效用，導致穿山甲這無辜的動物被瘋狂獵殺。也因為野外的穿山甲越來越少，所以穿山甲成了昂貴的食物，有些人僅僅是為了炫富而食用穿山甲，這樣的行為也把穿山甲推上最後的滅絕之路。雖然現在穿山甲在多個國家及地區均禁止出口及貿易，但是走私與盜獵依然存在！落實執法，逮捕並懲處這些盜獵者及食用者才能真正解決穿山甲的危機。科學家認為亞洲的穿山甲可能將於20年內滅絕！這不是我們想要的結果，現在就是解救穿山甲的最後機會。請別讓科學家的預言成真。這個作品我花了很多的時間，是一個難度很高的作品，自開始到完成創作至少修改了6個版本，不停地推翻與重建，因為我在挑戰一個美與機能都要兼具的作品。所以當我完成這個作品時，也同時愛上這個作品，因此有些捨不得分享出來。但我更期望朋友們也能夠親自體驗我的感受，能將牠握在手中，感覺牠的觸感、聲音與各種動態的變化。當你下載了並列印這作品時，願你也能像我一樣愛上這個作品。同樣的檔案我也分享於 <a href="http://fastlab.tw/" rel="nofollow">http://fastlab.tw/</a> 這是台灣資訊策進會的3D分享網頁，希望各位3D玩家也能慢慢豐富這個地方。感謝 新光合成纖維股份公司 訂製專用顏色之3D列印材料贊助本作品創作。列印建議 層高0.2mm 免支撐 縮小列印時請別小於0.75並提提高解析度到0.15mm</div><h1>Custom Section</h1><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=fkWxOLbFxPI"><iframe src="//www.youtube.com/embed/fkWxOLbFxPI" frameborder="0" allowfullscreen="allowfullscreen"></iframe></div></div>