longman

ppastur

We have aluminium sliding windows in our house and wanted a way to lock the travel of the widows without having to drill holes in the window frame. This device works nicely and is easy to adjust and remove leaving no trace. I added a rubber bumper (<a target="_blank" href="https://www.amazon.com.au/Dampone-Adhesive-Dampening-Glassware-Furniture/dp/B08K3B58JB/ref=sr_1_1_sspa?crid=16RUWZ4Q8I94I&keywords=rubber%2Bbumper&qid=1705210394&sprefix=rubber%2Bbumper%2Caps%2C251&sr=8-1-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9hdGY&th=1" rel="nofollow noopener">like this</a>) to the end of the screw to stop the device from sliding.&nbsp;<ul><li>0.20mm layer height</li><li>BBL PETG white</li><li>printed both items upright</li><li>normal support enabled for the main body hole and disabled support for the screw</li><li>print time 38 min</li></ul>

Sliding window stop

Household

Trig

Don&#39;t want to spend all that money for some fancy magnetic cable management system? Like to DIY your own solutions? Well the LTT Cable Tie Wire Management Bracket is here for you! Just like this message from our spo… wait, no. This isn&#39;t an actual LTT product and I&#39;m not sponsored. I&#39;m just some random fat dude who got his hands on some 3d printers and some 3d modeling software. But, I get to legitimately use the LTT tag and hopefully get this thing noticed!&nbsp;These brackets are designed with the LTT Cable Ties in mind, but do work with other brands I&#39;ve tested. They&#39;re perfect for just tidying up those pesky cables under your desk and I&#39;ve been personally using them for about 3 months with no issue. The best part? They only cost a few grams of filament and a single screw!&nbsp;Parts needed:(1) LTT Cable Tie(1) M4 Countersunk Screw(1+) Cable that needs managing&nbsp;Find the wide version here: https://makerworld.com/en/models/486065#profileId-398711

Cable Management Bracket for LTT Cable Tie

Striper and boating

Onkelsam

Homer J. Simpson Wallart&nbsp;Attach with double-sided tape

Homer Simpson Wallart

Decor

Kit Crafters

This is a minimal, but sturdy, stand/display for Mechanical Keyboards. It should fit any sized keyboard well and is plenty sturdy, even with PLA.&nbsp;A friend of mine asked me to print a keyboard stand for them in a stronger material because the ones they were gifted kept breaking. I found that the issue wasn't because the PLA was weak but because the design was flimsy so I designed a new stand for them that is much more sturdy while still being printed in PLA. I hope this design works well for you too!&nbsp;The keyboard in the image was a gift from a friend, the NK65 Olivia Edition.

Minimal Sturdy Keyboard Stand

Desk

make 3D

The Perpetual Calendar&nbsp;A fully 3D printed calendar. No Magnets, no bolts, no glue and no screws are needed. Just 3D printed parts.  If you don't have an AMS unit, you can just print the date/month tiles in one color - Then you use a Posca Marker or similar to add the date and months.&nbsp;I seperated each color print (besides the date/months tiles) to individual print plates. Please move these around as you please for faster or more eficient prints.&nbsp;NB: When assembling the calendar please only tighten the axis so you can still move the date and month individually.&nbsp;The indicator tiles needs to be inserted in this order.<figure class="image image_resized" style="width:56.57%;"><img src="https://makerworld.bblmw.com/makerworld/draft/467143/2023-12-30_2ce15f6f96ba7.png"></figure>NOTE: The two housings are not the same.The centerblock one for the days is 31,4mm - The centerblock for the months is 28,8mm&nbsp;If you’re having issues with adhesion in general with your printer - please use the print profile with added brim to the threaded axis. &nbsp;Please have a look at this assembly video I've made. If you follow these steps it's a very simple assembly.<figure class="media"><div data-oembed-url="https://youtu.be/XVZG9G0sLQw"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/XVZG9G0sLQw" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>This video shows how to orient the date tiles so the calendar works as intended.<figure class="media"><div data-oembed-url="https://youtu.be/AJB0iBZT9bc"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/AJB0iBZT9bc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;Please make sure you print bed is clean when printing the multicolor parts to ensure maximum adhesion.&nbsp;Due to the nature of 3D printed parts being very light, you might encounter that the tiles won't fall down immediately. If this happens just give the housing a little tap and it should fall into place.&nbsp;My calendar is printed with these filaments:Sunlu PLA+ White (I am having bed adhesion issues with this filament - I recommend Bambu PLA White instead)Sunlu PLA+ BlackBambu Lab PLA Basic Orange UPDATE 31-12-2023:Uploaded a new print profile. Version V1.1Made a few modifications to the two housings so the tiles would fall down more consistently.This update also reduces the print time by more than 1 hour.&nbsp; UPDATE 08-01-2024:Some users have been complaining/leaving low ratings about the ironing of the tiles or bed adhesion.  Please modify this yourself within Bambu Studio if your printer is not well calibrated or maintained.  Also, make sure your printer bed is clean from any grease.  I've had zero issues with my own prints. both ironing and bed adhesion.  Printed on a P1S.&nbsp;&nbsp;

"Date Keeper" Perpetual Flip Calendar (Fully 3D printed)

Desktop

foramusementonly

Lateral hinge cover for Godzilla pinball by stern

Godzilla pinball Hinge cover

Pinball

Hearthquake

HSW Universal Controller Mount&nbsp;Small controller mount for Honeycomb wall storage (HSW) system. I've tested it with Xbox one/series, PS4 and switch (pro) controllers. Designed to match the HSW esthetics. &nbsp;Two versions available:<ul><li>Insert version that you can use in combination with the hollow inserts from <a target="_blank" href="https://www.printables.com/model/152592-honeycomb-storage-wall/files" rel="nofollow noopener">the original HSW model</a></li><li>Connector version that will fit directly in the HSW<ul><li>You might need to adjust the scale to get a nice fit</li></ul></li></ul>I've printed in PLA:<ul><li>0,2mm layer height</li><li>3 Wall Loops and </li><li>15% infill</li><li>No brim</li></ul>However, I feel like it can handle quite a range of settings and materials. &nbsp;Please let me know you're experience with other controllers. This is my first upload so tips and comment are welcome!&nbsp;&nbsp;

HSW Universal controller mount

Adam L

I remixed this controller to add a little depression for standard command strips, so the mount should be more flush to the wall itself. A minor cosmetic improvement that's important for me.

Xbox Controller Wall mount with slot for command strip

Mounts

erinfezell

<div><h1>Summary</h1><div>I work in the tech industry and this meme/comic, much like everyone else, has become a visual representation of the chaos we are subjected to on the daily. I had sought out to make something special for my coworkers and decided I would make my own take on this piece. Here are the details of the changes I made as I wanted it to more closely resemble the comic...EDITS MADE TO DOG: <ul><li>Added smile</li><li>Changed nose some</li><li>Added the black strip to his hat</li><li>Changed his eye shape</li><li>Changed his arms, making them more natural</li><li>Added hands to rest in his legs like in the comic (also helps with better printing)</li></ul>NEW ADDS:<ul><li>Created a new base with cut-outs of the individual pieces, which allows for pressure fitting of printed pieces</li><li>Created new speech bubble that is the same shape and font used within the original comic</li><li>Added more flames and changed composition for more visual impact</li></ul>I printed this with a Bambu Labs X1 Carbon printer, using a single AMS (allows for four color prints). There were changes that I made to the slicer, but I won't get into those details as those items will vary greatly on experience/slicers used. I have multiple files that will allow for MMU (multi-material) prints. Note that you may need to separate shells within your slicer to do so. FILAMENT NOTES: I used PLA for all pieces (details and links below); also used clear PET-G as the top layer on supports for the flames which allowed for very beautiful bottom layers. <ul><li>BASE: Black Glitter PLA</li><li>Speech bubble: Natural (clear), Black, and White PLA</li><li>Chair/Table/Hat: Brown PLA</li><li>Mug: Stone Marble PLA</li><li>Dog: Tan, Black, White PLA</li><li>Flames: Yellow and Orange PLA and clear PET-G for top layer of supports</li></ul>ADDITIONAL PRINTING POINTERS: <ul><li>Speech Bubble: In order to achieve the stick to remain clear and the speech bubble outline to not lose it's shape, I had to actually leave the pieces separated within the Bambu Labs slicer but place them slightly on top of one another. So I have included the separate speech bubble pieces in the event other slicers have the same experience. </li><li>Fire was printed laying down, with the above note of using PET-G as the top layer on the support. </li></ul>Please respect the Creative Commons licensing, as this is not approved to be sold in any format. ASSEMBLY NOTES: <ul><li>The various flames are inserted via one corner first then pushed and rocked down via the other side in order to pressure fit into their respective places.</li><li>I used Gorilla Glue Super Glue to permanently adhere the pieces in place AFTER test fitment. Placed just a couple of drops/small line in each respective hole within the base as well as a small dot on the bottom of the mug to adhere it to the table. </li></ul>Links for filament: <ul><li>Black Glitter PLA: <a href="https://a.co/d/bqyutzh" rel="nofollow">https://a.co/d/bqyutzh</a></li><li>Yellow PLA: <a href="https://a.co/d/4QwmVSE" rel="nofollow">https://a.co/d/4QwmVSE</a></li><li>Orange PLA: <a href="https://a.co/d/6pmjSfa" rel="nofollow">https://a.co/d/6pmjSfa</a></li><li>Brown PLA: <a href="https://a.co/d/c11qDMp" rel="nofollow">https://a.co/d/c11qDMp</a></li><li>Tan PLA: <a href="https://a.co/d/jajHU5W" rel="nofollow">https://a.co/d/jajHU5W</a></li><li>Stone PLA: <a href="https://a.co/d/eHBaeEX" rel="nofollow">https://a.co/d/eHBaeEX</a></li></ul></div><h1>Print Settings</h1>Printer: <div>Bambu Labs X1 Carbon</div> <pre><code> Rafts: <div>No</div></code></pre> Supports: <div>Yes</div> <pre><code> Infill: <div>20</div></code></pre> Filament: <a href="http://www.amazon.com/s?url=search-alias&field-keywords=See+Comments+PLA" target="_blank" rel="nofollow noopener"> See Comments PLA </a><pre><code> See comments</code></pre></div>

This is Fine Dog Remix

Gifts

jonto81

the classic Jurassic Park sign My settings for printing are the 0.2mm standard on Bambu slicer with a couple of tweaks:<ol><li>Fuzzyskin - Contour 0.4mm distance and 0.1mm thickness</li><li>No Brim</li><li>Wall Generator - Arachne</li><li>increase the flow ratio slightly - go from 0.98 up to 1.05</li></ol>Use a Textured PEI Plate and you should be all good The back plate is a tight fit - it can hold the light up on the wall without gluing For lighting on all of my light boxes I am using a USB powered LED light from Amazon with a bluetooth controller allowing me to control from my phone

Jurassic Park Light Box

Movies and games

Ken Mills

The normal size has a 160mm internal (max roll size) and 32mm post diameter (max hole size). The medium and small sizes are 140mm and 114mm respectively. The jumbo version has a 180mm internal and 38mm post diameter to accommodate larger rolls.&nbsp;After adding the towel roll with the end free, spinning the roll clockwise should automatically feed the end out of the side slot. Tear a sheet off by pulling from the bottom upward and towards the right edge of the slot.&nbsp;Feel free to increase the holder's height. I chose 180mm high to fit my bed, and I don't think I would go much shorted, but I think taller wouldn't hurt.&nbsp;Add three rubber pads or feet to help prevent sliding. I have a spot on my workbench paper towels live, so I just may attach it with some double-sided tape to create a semi-permanent home for a roll.

Spiral Vertical Paper Towel Holder

Garage

MEAF designs

Easy to print and fun to make!Perfect for your candy table, coffee table or any corner of your house&nbsp;&nbsp;Specially designed to fit in the buildplate of any mid size printer.The base is one piece. and every letter and details are separated files so you can print it in different colors even without an AMS.&nbsp;Designed two styles for every “O”. so you can choose what you like.<ul><li>First "O": choose between santa claus or tree ornament</li><li>Second “O”: choose between snowman face or snowman body</li><li>Third “O”: choose between reindeer or christmas elf</li></ul><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/1795494732/draft/2023-09-02_n84evi4tipld.gif"></figure>&nbsp;split the "Details" file in to parts with your slicer and just print the details you like for each one and glue them on top!<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/1795494732/draft/2023-09-02_o1xtzxx4tz4i.png"></figure>&nbsp;&nbsp;&nbsp;Print SettingsMaterial: PLA / PETGLayer height: 0,28 mm for letters and base. --- 0.2 for detailsNozzle diameter: 0,4mm or 0,6mmInfill: 10 -12%Perimeters: 2Supports: no&nbsp;Printing Tipthe tolerances are a little tight, so you will need some glue depending on your printer and/or filament calibration&nbsp;&nbsp;&nbsp;

Christmas hohoho Sign

Christmas

KYZ Design

Gridfinity baseplates completely remodelled from scratch, designed to minimise print time.<ul><li>Lower overall height (top trimmed)</li><li>Flares on the bottom removed</li><li>Smaller radii</li></ul>Designed for PLA and other materials with good first layer adhesion. You may need to add a brim to print with ASA/ABS. Print <a target="_blank" href="https://makerworld.com/en/models/76537" rel="nofollow noopener">these bins</a> next! <img src="https://makerworld.bblmw.com/makerworld/draft/285381/2023-11-28_4d90d07fb6c75.png">&nbsp;Check out <a target="_blank" href="https://makerworld.com/en/u/11128021/collections/26498" rel="nofollow noopener">this collection</a> for my other Gridfinity models andcheck out <a target="_blank" href="https://makerworld.com/en/u/11128021/collections/18964" rel="nofollow noopener">this collection</a> for my Honeycomb Storage Wall models.

Gridfinity Superlight Baseplates

Gridfinity

MakeIt3D

<h2>Summary</h2>Tired of receipts, dust, and other debris clouding your workspace?This 3D Printable Mini Trashcan is the perfect tool for throwing away, storing, or disposing trash and other belongings.This print features a fully functioning built-in swing allowing you to store items inside without things accidently falling out.This item is easy to print featuring 2 main files<ul><li>LID STL</li><li>Bottom STL</li></ul>Total Size of the product is roughly 6 inches Height, 3.5 inches Width, 3.5 inches Length.Feel free to print out the designs and share photos of your results. I would love to see them. All MakeIt3D Designs are made and designed in-house. When you purchase any of these designs you do NOT have the rights to sell the digital files or printed models. 3D PRINTING SETTINGS Printer Used: Bambu Labs X1 Layer Height: 0.2 Infill: 10% - 15% Honeycomb Print Speed: Slow Speed on First Layers Material: PLA Wall Count: 2 Walls

3D Printable Mini Trash Can for Car and Office Use

Cars

Williams Industries

Layered/textured bat &nbsp;Check out all of our great fun stuff over on our Patreon: https://www.patreon.com/WilliamsIndustries

Halloween Bat

Halloween

JDJDJD

<h2>Meet the Smoothy!</h2>The Smoothy is a PTFE Bowden Tube Y Connector designed for smooth filament transport without catching or binding. This allows you to use an external spool with your Bambu Lab machine without disconnecting your PTFE Bowden Tubes.&nbsp;PTFE tubes are inserted deep into the connector for less wear on the FDM material. This allows for silky smooth operation.&nbsp;As the filament progresses towards the output, it passes through a precisely-designed taper that mates perfectly with the output bowden tube.&nbsp;All PTFE tubes must be inserted until each “stop” is reached (see cutaway diagram).&nbsp;Connectors must be the black type (not blue). The black connectors allow the PTFE tube to “pass thru” which is required for the design to work smoothly: <a target="_blank" href="https://www.amazon.com/gp/product/B0B97RWKQR/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;th=1" rel="nofollow noopener">https://www.amazon.com/gp/product/B0B97RWKQR/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;th=1</a>&nbsp;<h2>BENEFITS:</h2><ul><li>No Supports</li><li>No Overhangs</li><li>No Brims</li><li>Optimized Geometry</li><li>Designed for FDM Printing</li><li>Smooth Operation</li><li>Supports both PC4-M6 and PC4-M10 “pass thru“ connectors</li><li>Free to Download!</li></ul><h2>UPDATES:</h2><ul><li>The Smoothy Mount is now available! Download here: <a target="_blank" href="https://makerworld.com/en/models/18190" rel="nofollow noopener">https://makerworld.com/en/models/18190</a> The mount is not required, but available to those who prefer to attach the Smoothy to their machines. Without the mount, it can simply rest in-line.</li><li>Both PC4-M6 and PC4-M10 connectors are now supported.</li></ul><h2>TIPS:</h2><ul><li>Make sure ALL bowden tubes are FULLY inserted until each one reaches its stop point. See cutaway diagram for an illustration.</li><li>The output tube does not insert as deep as the input tubes.</li><li>After inserting each tube, you can rotate the tubes back and forth while pressing inward slightly to make sure they&#39;re seated squarely and fully.</li><li>Glue Stick is recommended.</li><li>PTFE tubes must be cut squarely at the tip (no angled tips).</li><li>All PC4 connectors must be installed for a completed design with smooth operation.</li><li>Tested with a 0.4mm Nozzle and 0.2mm Layer Height.</li><li>Print vertically with wide dual-port side on the bed.</li><li>PC4 connectors typically have tapered threads. As such, make sure you don&#39;t over-tighten them as they can create a “wedge effect” and can cause damage.</li></ul><h2>NOTES:</h2><ul><li>These work well printed in PLA. More durable materials can be used, but it may require clearance adjustments.</li><li>I’m currently using this for my Bambu Lab X1C with an AMS, which utilizes an external spool.</li><li>This is the first model that I&#39;m sharing, I hope you enjoy it!</li><li>The Smoothy can be used commercially, but can&#39;t be resold.</li></ul>