kirkwilliams70

crabstiks

Robocop movie poster fridge magnet.&nbsp;Measuring 65mm wide by 95mm high by 5mm deep&nbsp;4 colour AMS print, using black, silver silk, white and beige.&nbsp;This needs 4x 8mm diameter by 2mm deep magnets, the magnets push into the model after printing, no need to pause.&nbsp;NOTE - The magnets are designed to be a tight fit. The best way to insert them is to line up a magnet with a hole then place the model on a hard flat surface facing up, with the magnet on the hard surface, then press down firmly on the model. The magnet will snap into place. Repeat for each magnet.&nbsp;&nbsp;

Robocop movie poster fridge magnet

Magnetic Things

DesignCraft

This adapter system wraps the edges of a DURAMIC 1kg 199x66mm cardboard spool in order to:<ul><li>provide smooth rotation within a Bambu Lab AMS</li><li>prevent carboard debris from depositing within a Bambu Lab AMS</li></ul>Features:<ul><li>Reusable</li><li>DURAMIC nameplate for easy identification when reusing</li></ul>Instructions:<ul><li>Print this model twice for a single spool</li><li>Affix one spool ring adapter on each side of the DURAMIC spool</li><li>See attached photos</li></ul>Notes:<ul><li>Shown as printed with Bambu Lab PLA Basic at 0.2mm</li></ul>Considerations:<ul><li>Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.</li><li>Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.</li><li>AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">AMS Lid Riser</a> which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on <a target="_blank" href="https://makerworld.com/en/u/243407759" rel="nofollow noopener">my profile</a> or directly here: <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">https://makerworld.com/en/models/33133</a></li></ul>

DURAMIC Bambu Lab AMS Cardboard Spool Adapter Ring

Filament 

Thicc

Are you tired of boxes slipping and sliding around your trunk? Not anymore with these vehicle trunk retainers. Construction is easy. Print and attach 20mm velcro hooks to the retainer&#39;s foot. The best aspect of this design is the velcro allows for the retainers to be infinitely reused and reorganized.&nbsp;Print Settings<ul><li>Use a 0.4mm nozzle, I cannot guarantee the success of other sizes</li><li>warmer climates should consider printing this in ABS or ASA</li><li>15% infill</li><li>.25mm first layer to improve adhesion.</li></ul>Update - proven that articulated retainer can print laying flat, which is much easier and quicker to print. Print profile adjusted to include this change

Car Trunk Velcro Retainer 

Chrobakx

I want to thank you all for the boost coupons you sent me. I really appreciate them.&nbsp;This is my version of Articulated crystal dragon.Print the outer walls slow, keep cooling on, clean your bed and your dragon will be fine.When removing from build plate, be careful not to brake any chain links. You can wait for build plate to cool down.Do not scale down, it will be fragile.

Articulated crystal dragon

Dragon 

bayfaire

My Free Bust of ironman which is a part of my newly created Custom Bust Series.&nbsp;Check out the entire Collection of my busts here: <a target="_blank" href="https://makerworld.com/@bayfaire/collections/942237" rel="nofollow noopener">https://makerworld.com/@bayfaire/collections/942237</a>I will be updating often with free and premium busts so please do follow me on Makerworld and Patreon!&nbsp;Grab commercial use access to my busts at my Patreon + other premium models!Patreon: <a target="_blank" href="https://www.patreon.com/Bayfaire/" rel="nofollow noopener">https://www.patreon.com/Bayfaire/</a>&nbsp;Patron's also receive PNG images of all bust models to create their own previews!&nbsp;All busts will follow the same base stand as this free one so you wont have to worry on reprinting and testing every time!&nbsp;Some Settings information:busts will come with a variety of models allowing you to multi-color your bust. The bust, stand, and even the text base insert portion can be printed separately and inserted into the stand.An circular insert is placed inside the bust itself for easy assembly to the pole and the standNote: Text box Insert is a tight fit with low tolerance, if you would like a more easier fit then lower size from 99% to 98% or 97% or size down the x,y,z by 1mm on each side&nbsp;Added STl's to print the entire bust in 1 go and split parts of the bust as well. Textbase_insert.stl works on all of the bust models

Iron Man Bust

Ironman

The Big Greek

Phone Stand 2024 Hi I would like to introduce you to my Phone Stand 2024.I think phone stands are just great. They are easy and quick to print and you can never have enough of them :-)You don't need an AMS for this one. Just print all the parts, stick them together and you're done.&nbsp;UPDATE 14.03.2024&nbsp;<figure class="table" style="width:98.39%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td style="text-align:center;" colspan="2">Complete your desk with the 2 new models in the same design as the phone stand</td></tr><tr><td>Business Card Holder<a target="_blank" href="https://makerworld.com/en/models/253496#profileId-269932" rel="nofollow noopener">https://makerworld.com/en/models/253496#profileId-269932</a></td><td><figure class="image image_resized" style="width:30.52%;"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-03-14_e8318022c0223.jpg"></figure></td></tr><tr><td>Pen Holder<a target="_blank" href="https://makerworld.com/en/models/253471#profileId-269896" rel="nofollow noopener">https://makerworld.com/en/models/253471#profileId-269896</a></td><td><figure class="image image_resized" style="width:30.09%;"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-03-14_0b91c40d9d56a.jpg"></figure></td></tr></tbody></table></figure>&nbsp;&nbsp;<figure class="table"><table><tbody><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;text-align:center;">Also check out this Phone Stand if you are interested. Split-Phone-Stand 2024 <a target="_blank" href="https://makerworld.com/en/models/169860?profiled=186535#profileId-186532" rel="nofollow noopener">https://makerworld.com/en/models/169860?profiled=186535#profileId-186532</a></td></tr><tr><td style="border:1px solid rgb(191, 191, 191);padding:0.4em;"><figure class="image image_resized" style="width:167.885px;"><a href="https://makerworld.com/en/models/169860?profiled=186535#profileId-186532" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-02-03_2ad417cb9457e.jpg"></a></figure></td></tr><tr><td style="text-align:center;">UPDATE 03.02.2024  Also check out this Phone Stand if you are interested. It's a 3-ANGLE Phone Stand <a target="_blank" href="https://makerworld.com/en/models/169772#profileId-186430" rel="nofollow noopener">https://makerworld.com/en/models/169772#profileId-186430</a></td></tr><tr><td><figure class="image image_resized" style="width:18.65%;"><a href="https://makerworld.com/en/models/169772#profileId-186430" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-02-03_039c3598d2fbb.jpg"></a></figure></td></tr></tbody></table></figure>If you like my work/project consider supporting me with these options:<ul><li>leave a like</li><li>leave a comment</li><li>download the file</li><li><a target="_blank" href="https://www.buymeacoffee.com/thebiggreek" rel="nofollow noopener">or By me a Coffee</a></li></ul><h3>This article/post/text or the print profile as well as the finished print may not be used for commercial purposes.</h3>Have fun printingTBG&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_16be5c7fdcb9f.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_52fde81037999.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_4c5855c0935ab.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_e3ac89cf4bdd8.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_904b0eb62ac33.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/702750/2024-01-28_28f2834273aa7.png"></figure>Please no commercial use

Phone Stand 2024 (No AMS needed)

Phone 

azi3dprint

Looking for a way to organize my desk better, I've come up with an idea to store my two SanDisk portable SSD drives in one convenient location, which is this drives holder. By attaching this holder to my monitor pole, I've made them easily accessible and always within reach.

SSD Drive Holder

Hard Drive case

LemonArts

Here is my new Design, the Desert Eagle Card Holder  <img src="https://makerworld.bblmw.com/makerworld/draft/454372/2024-01-26_90d0cfe2ceb4e.jpg">  This Card Holder can hold cards of any size. Cards in the 85x55mm, 89x55mm format sit flush with the outside of the stand. The stack of cards can be up to 15mm thick.

Desert Eagle Business Card Holder

Office 

Marco Tiburtini

My ultimate box to hold your battery! Thougt for AA, AAA, LR44, CR2032 and MN21 battery.With a practical cover that will allow you to transport the batteries without mixing them.I Hope you will enjoy it!&nbsp;Warning: print this project swiching off the Auxiliary Fan and setting the temperature of plate at 60 degrees.

Batteries Holder Box Organizer

Organizing 

Sakul

“Box Of Everlasting Roses With Custom Name Tag” Perfect gift for your significant other that you can customize to celebrate your relationship on Valentine&#39;s Day.This box of roses doesn&#39;t need water and will never wilt away. To customize the Name Tag: - Press on Object under Process - Rightclick on Textshape - Change your Text (you can also choose different fontsizes and styles here)   How to build: Print all the parts out; the provided design is optimized to cut down print time while maintaining a high-quality finish. Insert the pins into the roses. Place the inlay into the rose box.<figure class="image image_resized" style="width: 67.36%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000150617/design/2024-01-21_30d453ae60eef.jpg"></figure> The inlay needs to be printed without top and bottom layers. The exposed infill will act as a guiding grid for the roses.<figure class="image image_resized" style="width: 67.2%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000150617/design/2024-01-21_1c227a7a96f8b.jpg"></figure> The name tag is aligned on the front side of the box. Fix the name tag in place with some glue. There is also a version without the name tag that can be found in the raw model files.<figure class="image image_resized" style="width: 69.22%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000150617/design/2024-01-21_9ae7d7abfb4ac.jpg"></figure> Put the lid on and gift it to your loved ones.  If you like my work and want to support me in creating more free original designs, I would very much appreciate it if you <a target="_blank" href="https://ko-fi.com/sakul" rel="nofollow noopener">“buy me a coffee”.</a>  Check out my newest Uploads: <figure class="table" style="width: 95.25%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/439005#profileId-344550" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000150617/design/2024-04-22_dc79389f19d97.jpg"></a><figcaption>❤️“Heart of Everlasting Roses”❤️ </figcaption></figure></td><td><figure class="image"><a href="https://makerworld.com/en/models/484385#profileId-396742" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000150617/design/2024-06-04_88000876832aa.jpg"></a><figcaption>🍦Pop &amp; Catch Toys Ice Cream Cone🍦</figcaption></figure></td></tr></tbody></table></figure>

Box Of Everlasting Roses With Custom Name Tag

Wife

Williams Industries

Both plates included in the file, one main, the other is the backside. Opening was done in BS so you can edit it to your liking.&nbsp;We have a lot of great stuff over at the Patreon: <a target="_blank" href="https://www.patreon.com/WilliamsIndustries" rel="nofollow noopener">https://www.patreon.com/WilliamsIndustries</a>&nbsp;Patreon includes commercial use on all prints.

This is the way lightbox 

Lightsaber

MTKDesigns

This model is the Original Jordan 1&nbsp;&nbsp;&nbsp;The supports on the bottom are a little time consuming to remove.  I hit it with the orbital sander for a min or 2 with 80 grit and then again with 320 and it will smooth out.  &nbsp;***NOT for commercial use***I have had a LOT of interest in a  Commercial license on these.  I have created a Patreon just for this purpose.<a target="_blank" href="http://patreon.com/MTKDesign" rel="nofollow noopener">patreon.com/MTKDesign</a>

Nike Air Jordan 1 (Original Uploader)

Jordan

thedecember87

funny "bambuhub" logo made in 2 versions, with a hole to use it as a key ring or without a hole to apply it with double-sided tape wherever you want, in my case to the printer itself, there are 2 printing profiles, one with a hole and one without, already prepared for multicolor and there are also 2 separate ifle steps in case you want to do them to your liking

Bambuhub keychain/logo

Bambi X1C

FlorinV

Please share your make and let me know your opinion about this model. Thank you and have a great week !&nbsp;Update 11.03.2024: Added “Skull" lid. There is an optional profile for printing this lid. <a target="_blank" href="https://makerworld.com/en/@timon1201" rel="nofollow noopener">@timon1201</a> did a similar lid and gave me this idea. thanks !&nbsp;Update 29.12.2023: Added “Pine cone” lid. You can find it in the Optional Lids profile. The lid has fine details, please be sure your printing plate is clean (no finger grease etc.).&nbsp;The Automatic Toothpick dispenser:<ul><li>All parts are 3d printed, all in one plate. No AMS needed.</li><li>Several Lids to choose from and a clean lid to customize it as you wish. “Voronoi” and “Yoda” lid are found in the model profile. Other optional lids will be added to the “Optional Lids” profile.</li><li>Each part easily fit together. Please check the short building video bellow. ( 1min 30sec minutes to build )</li><li>works with toothpicks of max 66mm and approx. 2mm diameter (normal toothpicks I've found ). Please shake the dispenser to arrange the toothpicks correctly and parallel. Throw away toothpicks that look too different than normal ones: damaged, askew.</li><li>The two arms that hold the big parts together have printed on them L and R, to be sure you set them correctly (left and right).</li><li>The 3d printed spring should be inserted like in the video, first on the back with the other end up, then the front.</li></ul><figure class="image image_resized" style="width:30.4%;"><img src="https://makerworld.bblmw.com/makerworld/draft/682841/2023-12-14_9977d673e0c9a.png"></figure><ul><li>Second spring is optional (the left one). After some use, it will work smoother, as the parts needs some time to slide easier one on each other. From my experience, the right spring is enough, but feel free to play around.</li><li>If some of the toothpicks are thrown, it means some of them are a bit too thin. You can dispense them better by releasing the push pad slower. :)</li><li>If at some moment it stops from giving toothpicks, it can happen that the feeding zone is blocked by two toothpicks (usually because some toothpicks are smaller/bigger, damaged, askew etc). It's easily fixed by shaking a bit the whole model and/or press harder on the push part.</li><li>The parts are finely designed to work together, so I suppose it's important to have a good filament and calibrated. Please use my tested profile.</li><li>You can choose from two different lids (in the main profile, more lids in a separate profile - Optional Lids). The “Yoda” lid is a separate plate as it's using AMS and 2 colors.  You can print it without AMS and leave empty space in the lid where letters and Yoda is (don't print the letters and Yoda).</li><li>I've added another profile (For Thinner Toothpick - only base part) containing only the base part for cases where your toothpicks are often flying out of the dispenser. This is usually a problem related too thin toothpicks. This part is only the base part which should handle such toothpicks.</li><li>Based on the review of eric.joschko (thank you!!), he scaled everything to 108% and everything works perfect for he's toothpicks which i understood they are 68mm length.</li><li>Based on review of Sven_fretz (thank you!!): “scaled everything up to 125% and it works fine with my 80mm toothpicks.”</li><li>For better spring action and to be sure they keep their power better in time, you can print only the springs with PETG.</li></ul>This is the building video (1min 30sec minutes ): <a target="_blank" href="https://youtu.be/BJucPYljE2o" rel="nofollow noopener">https://youtu.be/BJucPYljE2o</a><figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=BJucPYljE2o"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/BJucPYljE2o" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;If you like this model, please check out my new Salt & Pepper dispensers: <a target="_blank" href="https://makerworld.com/en/models/228050#profileId-245632" rel="nofollow noopener">https://makerworld.com/en/models/228050#profileId-245632</a><figure class="image image_resized" style="width:56.68%;"><img src="https://makerworld.bblmw.com/makerworld/draft/682841/2024-03-06_0e2805d6f36fc.jpg"></figure>&nbsp;Or, my fun and easy to print, easy to use filament cutter: <a target="_blank" href="https://makerworld.com/en/models/137257#profileId-149353" rel="nofollow noopener">https://makerworld.com/en/models/137257#profileId-149353</a><figure class="image"><a href="https://makerworld.com/en/models/137257#profileId-149353" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/682841/2024-01-15_0a30aa152023c.png"></a></figure>&nbsp;Disclaimer: YOU ACKNOWLEDGE, BY YOUR USE OF MY MODELS, THAT YOUR USE OF THE MODELS IS AT YOUR SOLE RISK.<h2>LIMITATION OF LIABILITY</h2>UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL OR EQUITABLE THEORY, SHALL THE DESIGNER OF THE MODELS BE LIABLE TO YOU OR TO ANY OTHER PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL LOSSES OR DAMAGES OF ANY NATURE ARISING OUT OF OR IN CONNECTION WITH THE USE OF OR INABILITY TO USE THE MODELS OR 3D PRINTED MODELS.

Toothpick Dispenser - all parts printed

Home

PhaseworksCA

Marvel at the iconic Iron Man with this low poly geometric 3D print, featuring the superhero standing facing boldly forward. This modern design captures his powerful stance in sharp, angular lines, perfect for fans of superheroes and contemporary art.&nbsp;Happy printing :)&nbsp;<figure class="image image_resized" style="width:100%;"><a href="https://www.printables.com/@PhaseworksCA/store" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/599315/2024-02-27_cbac20a9d0926.png"></a><figcaption> </figcaption></figure>

Geometric Low Poly Iron Man

Madness3D

Optimized for 3D printing with a amazing depth of field.&nbsp;The Glowing series is optimized for use with glow in the dark filaments for a mesmerizing effect.Charge the pictures with UV light for the most optimal effect. There will be 2 print profiles available.200x200 is optimized for x1c, p1s, p1p150x150 is optimized for A1 mini.&nbsp;Frames for both sizes can be found in my uploaded models.&nbsp;Pictures can be printed with out AMS by following the print instructions below.&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: Bambu Lab PLA Matte Charcoal Bambu Lab PLA Glow Blue Bambu Lab PLA Glow Yellow&nbsp;Swap Instructions: Start with Black At layer #7 (0.64mm) swap to Bambu Lab PLA Glow Blue At layer #13 (1.12mm) swap to Bambu Lab PLA Glow Yellow for the rest. &nbsp;Art generated with midjourney and optimized for 3D printing with Hueforge.

"Glowing" - Batman

Nakozen

Space: the final frontier. These are the voyages of the Starship Enterprise. Its five-year mission: to explore strange new worlds. To seek out new life and new civilizations. To boldly go where no man has gone before!First of the upcoming series of new sci-fi kits is of course the NCC-1701 Enterprise from Star Trek the Original Series.<a target="_blank" href="https://www.thingiverse.com/thing:4601489" rel="nofollow noopener">Find TNG's NCC-1701-D Enterprise kit here!</a>Two versions of the kit are included, one with a hanging loop and another without, alongside the individual part files. UPDATE 12/12/22: Version 2 has been added along with a tighter variant (labelled ‘Ti’)!------------------------------------------------------------Print at 0.2mm layer height, there really is no benefit from printing at a higher resolution and it could affect the fit. The model parts are 1.8mm high, which is not divisible by 0.16 for example!Be sure to print with 100% infill for it to hang straight as the weight distribution can be sensitive! Makes greatly appreciated, always glad to see them! Happy Printing!------------------------------------------------------------Interested in selling? All files are marked as non-commercial along with any remixes created from them.If you are interested in selling physical prints of my models anywhere, be it online or offline, you can obtain a sales license when subscribed to Tier 3 of my Ko-Fi memberships! <a target="_blank" href="https://ko-fi.com/nakozen/tiers" rel="nofollow noopener">https://ko-fi.com/nakozen/tiers</a>Want to show me you love me? Buy me a "coffee"...! <a target="_blank" href="https://ko-fi.com/nakozen" rel="nofollow noopener">https://ko-fi.com/nakozen</a>

NCC-1701 Enterprise Kit Card

Smart3d by Gabriel Gomes

<a target="_blank" href="https://www.patreon.com/posts/loki-led-lamp-90915111" rel="nofollow noopener">Loki Led Lamp</a><a target="_blank" href="https://www.patreon.com/posts/loki-led-lamp-90915111" rel="nofollow noopener">13 de outubro</a>&nbsp;🔱 Special for Loki Fans! 🔱Illuminate Your Space with the Mischief and Elegance of Loki!Introducing the Loki Themed Light, a unique masterpiece tailored for the true enthusiasts of the Marvel universe. Expertly crafted through 3D printing, this light isn't just a decorative accessory—it's a radiant tribute to the God of Mischief himself.🌟 Key Features:<ul><li>Majestic Design: Inspired by the intricate details of Loki's attire and his iconic horned helmet, every aspect has been captured to bring a touch of Asgardian royalty directly to your space.</li><li>Mystical Glow: Integrated LEDs emit a greenish, enchanting glow, setting the perfect ambiance for Marvel movie nights or diving deep into Norse mythology.</li><li>3D Craftsmanship: Printed with high-quality materials using cutting-edge 3D printing technology, ensuring durability and a finish that even Thor might envy.</li></ul>Step into the world of gods and mischief. Secure your 3D Loki Themed Light today and let your space shine with the allure of the Marvel universe! 🔱🌟🌌&nbsp;<h3>Video explaining name customization 🔗</h3><h3> </h3><h3>Video explaining Inglês here 👉 <a target="_blank" href="https://www.youtube.com/watch?v=UQFVBIzJuTE&t=65s" rel="nofollow noopener">Video</a> or <a target="_blank" href="https://www.patreon.com/posts/tutorial-79998205?utm_medium=clipboard_copy&utm_source=copyLink&utm_campaign=postshare_creator&utm_content=join_link" rel="nofollow noopener">Video </a></h3><h3>Video explaining Português here 👉 <a target="_blank" href="https://www.youtube.com/watch?v=hmGqF4oN_b4&t=590s" rel="nofollow noopener">Video</a> ou <a target="_blank" href="https://www.patreon.com/posts/tutorial-79998205?utm_medium=clipboard_copy&utm_source=copyLink&utm_campaign=postshare_creator&utm_content=join_link" rel="nofollow noopener">Video</a></h3><h3>Tinkercad Custom Fonts Português here 👉 <a target="_blank" href="https://www.youtube.com/watch?v=hmGqF4oN_b4&t=590s" rel="nofollow noopener">Video</a></h3><h3>Tinkercad Custom Fonts Inglês here 👉 Soon</h3><h3> </h3><h3>Video of material used 👉 <a target="_blank" href="https://www.youtube.com/watch?v=yRWmLu6s4ek" rel="nofollow noopener">Video</a> or <a target="_blank" href="https://www.youtube.com/watch?v=nkAmhxxbynU&t=282s" rel="nofollow noopener">Video</a></h3><h3> </h3><h3>Video explaining process 1 extruder 🔗</h3><h3> </h3><h3>Video explaining Inglês here 👉 <a target="_blank" href="https://www.youtube.com/watch?v=Zmqgbs5jFBU&t=329s" rel="nofollow noopener">Video 1</a> <a target="_blank" href="https://www.youtube.com/watch?v=7HGH8_x5Mec&t=2s" rel="nofollow noopener">Video 2</a></h3><h3>Video explaining Português here 👉 <a target="_blank" href="https://www.youtube.com/watch?v=qafZe33vO-Y&t=224s" rel="nofollow noopener">Video sem abl </a> ou <a target="_blank" href="https://www.youtube.com/watch?v=MXdp3aAKiBY&t=309s" rel="nofollow noopener">Video com abl</a></h3><h3> </h3><h3>Videos For Bambu Users 🔗</h3><h3> </h3><h3>How do i fix my gaps 👉 <a target="_blank" href="https://www.youtube.com/watch?v=RmknAHTkZ7k&t=111s" rel="nofollow noopener">Video</a></h3><h3>Bambu studio use STEP File 👉 <a target="_blank" href="https://www.patreon.com/posts/bambu-studio-85192101?utm_medium=clipboard_copy&utm_source=copyLink&utm_campaign=postshare_creator&utm_content=join_link" rel="nofollow noopener">Video</a></h3><h3> </h3><h3>Component Links For this Lamp 🔗</h3><h3>LEDs rgb 5v 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_98Vnlw" rel="nofollow noopener">Link</a></h3><h3>LEDs white 5v 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_9z6kJn" rel="nofollow noopener">Link</a></h3><h3>Controllers 5v🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DkAmFej" rel="nofollow noopener">Link</a></h3><h3> </h3><h3>Other links to parts I use 🔗</h3><h3> </h3><h3>Usb power boost linha dc 5v to dc 12v 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DCiKxWb" rel="nofollow noopener">Link</a></h3><h3>LEDs white 12v High Brightness 🛒👉 <a target="_blank" href="https://pt.aliexpress.com/item/33039307898.html?spm=a2g0o.order_list.order_list_main.173.46e6caa4NvGPx3&gatewayAdapt=glo2bra" rel="nofollow noopener">Link</a></h3><h3>DC Power Supply Jack 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DlYW7iL" rel="nofollow noopener">Link</a></h3><h3>Usb Cable 1M 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DDw0YOf" rel="nofollow noopener">Link</a></h3><h3>Usb Cable extension 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DBjzR0n" rel="nofollow noopener">Link</a></h3><h3>Button ON/OFF 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DELIRQ3" rel="nofollow noopener">Link</a></h3><h3>Charger Module usb-c for 18650 battery 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DkP0cAn" rel="nofollow noopener">Link</a></h3><h3>18650 Battery 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DenikD5" rel="nofollow noopener">Link</a></h3><h3>Pei plate 300x300 superior effect 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_A0j005" rel="nofollow noopener">Link</a></h3><h3>Pei plate Bambu Machine superior effect 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DdHORix" rel="nofollow noopener">Link</a></h3><h3>Kit Hotend para Bambu Lab clone, i use 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DcGXaNz" rel="nofollow noopener">Link</a></h3><h3>Spot Welder for 18650 Battery 🛒👉 <a target="_blank" href="https://pt.aliexpress.com/item/1005004573427677.html?spm=a2g0o.order_list.order_list_main.429.46e6caa4NvGPx3&gatewayAdapt=glo2bra" rel="nofollow noopener">Link</a></h3><h3>Copper Wire Toothbrush 🛒👉 <a target="_blank" href="https://s.click.aliexpress.com/e/_DBbI9w3" rel="nofollow noopener">Link</a></h3>

Loki Led Lamp

Marvel

NotTooShabbyCreations

First of haunted lightboxes nobody asked for :D &nbsp;For the light box you are going to need pink, white and black PLA. USB wire ( with a swatch preferably ) and a 5v cool white LED strip.Soldering iron and basic soldering skill required!!!&nbsp;Size:180mm x 225mm

Cat fingers  

Funny

Imagine-Reality

This model has been updated as of November 1, 2023. The gorilla is larger now and the lid support has more surface area and a recess for the lid handle screws. This should be a much more stable lid support. I also remodeled the gorilla with a better pose for raising the lid. If you're looking to lift the glass lid on your Bambu Lab printer temporarily, why not have a video game gorilla do it for you? This gorilla raises the front of the glass 46mm to provide sufficient venting when printing PLA. This prints face down with 5 colors using a single AMS. To do this, choose the first layer printing order as 1-tan, 2-brown, 3-white, 4-purple, 5-black. Load your AMS with tan in slot 1, black-2, brown-3 and purple-4. Assign white and tan to the same AMS slot (1) when starting the print. As soon as tan finishes printing and switches to brown, replace the tan filament spool with white. The print will continue and all remaining white and tan layers will use white filament. &nbsp;Don't forget to finish off the theme with the barrel handle. <a target="_blank" href="https://makerworld.com/en/models/98825#profileId-105363" rel="nofollow noopener">https://makerworld.com/en/models/98825#profileId-105363</a>

Arcade Gorilla Lid Lifter for Bambu Lab X1 Carbon, P1S, and P1P

Arcade

franceschellifederico

NOTE: USE MY PRINT PROFILE FOR BETTER RESULTS! NOTE2: TOLLERANCE ARE CALCULATED FOR BAMBU PLA. If you have any suggest, please don't esitate to leave a comment :)Tip: Print the body and the final part in two different times if you don't want to waste time due to the AMS filament change :oA re-usable scraper with a different end for any purpose!I've designed a 3D-printable scraper tool that serves multiple purposes: cleaning and removing models from the printer bed after use and also for removing ice from car windshields during winter! What's unique about my scraper is the interchangeable end piece, offering a choice between three models: one for cleaning the printer bed, another for lightly iced glass, and the third for heavily iced glass.Additionally, there's a slot (on the back) for 15x3mm magnets, allowing it to be attached to the side of the printer.Green: lightly iced glass, Blue: heavily iced glass,Orange: cleaning the printer bed.<figure class="image image_resized" style="width:45.15%;"><img src="https://makerworld.bblmw.com/makerworld/draft/415361/2023-12-04_f69102c74a9f4.png"></figure><figure class="image image_resized" style="width:36.97%;"><img src="https://makerworld.bblmw.com/makerworld/draft/415361/2023-12-04_8dadcc53d026c.png"></figure><figure class="image image_resized" style="width:30.41%;"><img src="https://makerworld.bblmw.com/makerworld/draft/415361/2023-12-04_601fad618ca39.png"></figure>&nbsp;&nbsp;