kevman

Geek Genius Collective

Giants helmet for all to print. Printed great first try for us. If you trust your printer to speed up the print go for it, these are just the speeds we use. I know the back can be printed faster easily, its just set to our face speeds on the 3mf so it says it takes 4 plus hours if you slice it without changing anything. Make sure you heat up and clean your nozzle of any old filament stuck to it before starting the print to prevent color wisps from left over filament. Enjoy and Happy Printing!

Giants Lightbox

light-boxes

mocodroid

This is my take on the slim wallet. No glue or other hardware require to assemble the wallet. There are 3 different versions of the wallet, all of them use the same bottom and top covers. The 2 wallets from the pictures were printed on PLA and PTEG. The multicolor wallet was printed on PLA using the MMU2S at .2mm layer height, 15% gyroid infill and 3 perimeters using a .4 nozzle. The white one was printed on PTEG using the same settings as the PLA one.For the wallet that hold 4 cards use the files that stat with 4 mm, for the one for 5 cards use the files that start with 5 mm and the one for 6 cards use the files that start with 6 mm. The wallet consists of 8 parts and 5 pieces of filament (1.75mm):<ul><li>Top Cover</li><li>Bottom Cover</li><li>Middle</li><li>Middle (X)</li><li>Lever</li><li>Clips (You will need 3)</li><li>5 pieces of filament cut to length according to the wallet size.</li></ul>To assemble the wallet start with the bottom cover, middle and the pieces of filament. You will need to clean the holes from the middle section a bit in order for the filament to go through the middle section. After you clean the holes put your middle section on top of the bottom cover and insert the pieces of filament on at a time. Cut them around 1 to 1.5 mm above the middle section. Once you have all your pieces of filament in, get you lever and lay it on top of the bottom cover where the space is between the small middle section and the skinny part of the big middle section. The last picture shows where the lever goes. Finally, you can put the top cover on, make sure that everything lines up and install the little clips. There are 3 cutouts for the clips, one on each side at the bottom and one at the top where the lever is. you need to push them with a bit of force for them to sit in place. Just put your cards in and have fun.Once you lift the cards, there will be some friction between the cards and the top part of the wallet where the lever is at, that fiction is necessary to keep the cards up.<figure class="image"></figure>&nbsp;<figure class="image image_resized" style="width:66.96%;"></figure>

Slim Wallet

wallet

rmnkzk

California 1972 license plate for a new 3D Sets Model 17: Sakura 240.&nbsp;Print either with filament change based on layers or using MMU or AMS.

Custom license plate for 3D Sets Sakura 240

Ambro Art

Multicolor jordan IV replica. &nbsp;measures 38.7 x 102 x 62.8

Jordan IV nike

misc

noriwl

A ghostbusters licence plate for decorating your house, garage or room for halloween. Prints in two hours with the AMS, or can be printed in white and colored with permanent markers or paint.

Ghostbusters ECTO 1A licence plate from Ghostbusters 2

halloween

YelTrik Designs - Click FOLLOW

ARC DESIGN! This arc design is a simple model and simple install and is a very effective in helping to reduce the likihood filament feed and pullback errors. This is not an overly complicated solution for the AMS internal hub! It doesn't require screwing something into place that could potentially damage your very expensive AMS! No screws required! It's critical the AMS internal PTFE hub function as designed without interference. This solution attaches only to the PTFE tubes improving and maintaining proper alignment of the PTFE tubes, at a consistent and specific distance from the hub, for smooth filament feeding and pull back! Simple design, print, and results.&nbsp;Check Out User Reivews and Feedback&nbsp;Simple To Print And Install:Simple to print and install. Don't be fearful of the install if you haven't yet dissembled your AMS. BL has an excellent and simple Wiki on this process. See Installation Procedure below.&nbsp;&nbsp;SEE INSTALLATION PROCEDURE BELOW <a target="_blank" href="https://makerworld.com/en/u/1072890529" rel="nofollow noopener">CLICK HERE TO CHECK OUT THESE OTHER PTFE ACCESSORIES</a>&nbsp;INSTALLATION PROCEDURE <a target="_blank" href="https://wiki.bambulab.com/en/x1/maintenance/replace-filament-hub" rel="nofollow noopener">https://wiki.bambulab.com/en/x1/maintenance/replace-filament-hub</a> NOTE: You do not have to remove the AMS Internal Hub. You only need to separate the AMS enclosure from the Spool Roller Assembly.&nbsp;Once you have the AMS disassembled it will look like this: <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/388682/2023-10-28_16513408f15088.jpg"></figure>&nbsp;&nbsp;The next step is to remove the PTFE tubes from the AMS Internal Hub:&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/388682/2023-10-28_a3bae2917401e8.jpg"></figure>Once the PTFE tubes have been removed from the Hub, install the AMS Filament Pull Back Guide on each tube. Move it up higher than needed initially<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/388682/2023-10-28_01acb3f912e128.jpg"></figure>&nbsp;After all the PTFE tubes have been installed in the AMS Filament Pull Back Guide, reinstall the PTFE tubes into the Hub and move the AMS Filament Pull Back Fix as seen in this photo:&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/388682/2023-10-28_3901d04a158868.jpg"></figure>&nbsp;Assemble the AMS in the reverse order you followed to disassemble it. NOTE: Remember to plug in the electrical connectors or you'll have to repeat the disassembly and reassembly procedure, which could be frustrating. Don't ask me how I know. ;-) That's It!

AMS Filament Feed & Pull Back Errors

printer-stuff

blecheimer

This is a spoon that allows fast and precise spooning. You can easily fill your smallest and largest desiccant containers without spilling the tiny pearls - say goodbye to funnels. The unscaled spoon can hold ~12ml that is 10g of silica-gel pearls.&nbsp;Update: Based on a comment of user fish_ I made a stand for this spoon: <a target="_blank" href="https://makerworld.com/de/models/28648#profileId-25036" rel="nofollow noopener">https://makerworld.com/de/models/28648#profileId-25036</a>&nbsp;Disclaimer: This work by blecheimer is licensed under <a target="_blank" href="http://creativecommons.org/licenses/by-nc-sa/4.0/?ref=chooser-v1" rel="nofollow noopener">CC BY-NC-SA 4.0</a> You are not allowed to copy this model to other 3D printing websites without my permission.

light-boxes

wallet

RC

misc

halloween

printer-stuff

tools