KETOO

Lvnatic

<h2>Included options/profiles:</h2>AIO Runners (Runner Version):<ul><li>All in One option. </li><li>Batman&#39;s Runner for the original frame/skeleton </li></ul>Upgrade Kit Runners (Upgrade Kit):  <ul><li>Only includes the Lady 13 Parts</li></ul>Split Runners:  <ul><li>The heels can be tough to print without supports, so I separated them from the main runner.</li></ul>Individual Armor Parts (No Runner Version): <ul><li>If you need to print spares/replacement parts.</li></ul>&nbsp;<h2>Print instructions:</h2><figure class="table" style="float:left;width:70%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><th style="padding:6px;">Layer height:</th><td style="padding:6px;">0.15mm (0.2mm first layer)  </td></tr><tr><th style="padding:6px;">Wall Ordering:</th><td style="padding:6px;">Outside to inside/Print external perimeters first</td></tr><tr><th style="padding:6px;">Infill: </th><td style="padding:6px;">15-20% rectilinear/grid/gyroid</td></tr><tr><th style="padding:6px;">Material:   </th><td style="padding:6px;">Armor - PLA, Frame - PETG/ABS/ASA</td></tr><tr><th style="padding:6px;">Supports:</th><td style="padding:6px;">Not needed/optional (for the heels)</td></tr></tbody></table></figure>&nbsp;<h3> </h3><h3> </h3><h3> </h3>&nbsp;&nbsp;&nbsp;<h2>Check out my other 13 models:</h2><a target="_blank" href="https://makerworld.com/en/models/381598#profileId-328653" rel="nofollow noopener">ETP-V13 Head</a>, a 13 Family compatible conversion of <a target="_blank" href="https://makerworld.com/en/@MakeAPrint246" rel="nofollow noopener">Make-A-Print</a>&#39;s ETP-V2!<a target="_blank" href="https://makerworld.com/en/models/424772#profileId-328208" rel="nofollow noopener">A13</a>, a mech themed 13 based on <a target="_blank" href="https://www.printables.com/de/@AndrewGipson" rel="nofollow noopener">Andrew Gipson</a>&#39;s Alouttinae<a target="_blank" href="https://makerworld.com/en/models/425174#profileId-328722" rel="nofollow noopener">A13 - Back Addons</a>, a weapons backpack and 4-Arm Addon for the A13&nbsp;<h2>Changelog:</h2>v1.22b (14.04.24):<ul><li>Updated the description</li></ul>v1.21b (14.04.24):<ul><li>Renamed the model to shorten the models name.<ul><li>&#39;Lady13 v1.21b&#39; sounds way cooler than ‘Lady 13 Runner (Dummy 13 Female Variant) V1.2’</li></ul></li><li>Updated the description and model names</li><li>Changed ‘Lady 13 ONLY Runners’ to ‘Lady 13 Upgrade Kit’</li></ul>v1.2 (19.12.23):<ul><li>Added the new Lady 13 ONLY runners!<ul><li>Save some filament if you don&#39;t want to reprint the complete set of armor!</li></ul></li></ul>v1.1 (15.12.23):<ul><li>Fixed a mesh issue with both AIO runners<ul><li>the neck piece wasn&#39;t connected properly</li><li>Didn&#39;t seem to cause any issues with printing but I fixed them regardless.</li></ul></li></ul>v1.0 (24.11.23):<ul><li>Last touches and small optimizations on the high heel runners</li><li>Release!</li></ul>v0.9.2 (23.11.23):<ul><li>Added a AIO v2 with original feet/toes</li><li>Added &#39;Individual Armor Parts&#39; folder for spares</li></ul>v0.9.1 (21.11.23):<ul><li>Combined the separate runners the the AIO ones</li><li>Added ‘All-In-One Runners’ folder</li><li>Added &#39;Separated Feet Runners&#39; folder</li><li>Small optimizations to the heels and printability</li></ul>v0.9 (20.11.23):<ul><li>Fixed the mesh on batman&#39;s runners</li><li>Remodeled the base runner to feature all female parts</li><li>Separated the high heels into its own runner</li></ul>

Lady13 v1.22b

小人道具

TBone_427120

This lampshade is designed for the <a target="_blank" href="https://makerworld.com/sv/models/13717#profileId-13429" rel="nofollow noopener">Bambu Led Lamp 001</a> kit ←- Follow this link to get the model for the base that holds the electronics and that this globe shade locks into.&nbsp;This is a moon lithophane model for the LED Lamp kit base built using NASA SVS data.&nbsp;Before printing, it is highly recommended to test and calibrate the filaments. Test Prints are provided in a profile to test the trickier parts of the print, in particular the top of the moon. Printing the sliced off moon top will give an idea if the flow rates need to be calibrated or if the layer heights need refining.Both of these are eSun PLA, and both were printed using the same eSun PLA+ profile. <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_e7cbdab0e3545.jpg"> The one on the left (&#34;creamy&#34;) needed different flow rate settings to avoid the gaps in the thin walls. Moral of the story: spend the extra 20 minutes to at least run the Auto Calibration for a new filament (and Manual isn&#39;t so bad to do either particularly if you print on the textured plate).&nbsp;The extra big brim is out of an abundance of caution. There is nothing worse than being ten minutes from the end of a 17 hour print and hearing *CRACK* followed by a spaghetti detected notification. If the test print indicates your filament needs a small center support for the top of the moon, “Normal/Snug” supports will work best. Use Manual supports (Auto will result in a ton of exterior supports for the base of the moon) and paint a small dot in the underside of the top of the Moon. The latest version of the model has been made a little thicker and is more forgiving for printing with most filaments. The part that interfaces with the lamp kit base can easily be made a different filament to match the LED holder material or just for variety. Just set the base filament for the “ModifyBaseSettings” modifier. Doing will require only one filament purge, no prime tower is necessary.<figure class="image image_resized" style="width:41.3%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_33ea3c815b5ef8.png"></figure>&nbsp;If using the modifier to make a material change at the base, make sure to pick two filaments that have good adhesion to each other.Because the print requires supports in the base and cleanly removing those supports is important for a snug fit to the lamp kit base, a test print is provided to make sure the filament and support settings will release cleanly. Normal snug supports provided the best results (tree supports required much more effort).&nbsp;<figure class="image image_resized" style="width:17.23%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_f00e2d2199c81.jpg"></figure>&nbsp;If you do use the center support, when removing don&#39;t pull at individual folds from the bottom. Use something to grab on multiple folds as far up as possible (a pair of kitchen tongs works well) and twist.<figure class="image image_resized" style="width:17.52%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_c2509972a68348.jpg"></figure>Twisting will put less stress on the top of the sphere and less risk of pulling away the moon surface. If you have wisps of filaments, resist the urge to use a heat gun because the variable thickness of the shell will contract non-uniformly under the heat. This is the result using a heat gun on a lithophane:<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000031191/design/2023-10-06_a27a97fbc55ec.jpg">&nbsp;

Moon Globe for LED Lamp 001

其他

Bambu Lab

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013716/design/2023-09-25_28088e30b1c02.jpg"></figure>This 3D-printed mouse has a futuristic hollow shell design, revealing its internal structure. This generative design shell structure is possible only with 3D printing. Our industrial designer fully utilized the advantages of a 3D printed structure to present you with this magnificently artful mouse.&nbsp;Recommended filaments: Bambu PLA series<a target="_blank" href="https://store.bambulab.com/collections/bambu-lab-3d-printer-filament?gf_60645=279355719795" rel="nofollow noopener">https://store.bambulab.com/collections/bambu-lab-3d-printer-filament</a>If using PLA matte, metal, silk, please slowly screw in the bolt and avoid over-tightening to prevent structural damage.Print Setting: Print without support, v2.0 print profile recommendedHardware Kit: Wireless Mouse Components Kit-002<a target="_blank" href="http://store.bambulab.com/products/wireless-mouse-components-kit-002" rel="nofollow noopener">http://store.bambulab.com/products/wireless-mouse-components-kit-002</a>&nbsp;Please make sure you clean the build plate before printing and/or applying glue to prevent print failures.&nbsp;Follow the Assembly Guide or video tutorial below step by step to print and assemble your build. Refer to the Design Guide for further design and quality enhancement.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000013716/design/2023-09-15_12b653452832c.png"></figure><figure class="media"><oembed url="https://www.youtube.com/watch?v=lkOg_X4qjW8"></oembed></figure>

小人道具

其他

工具

玩具