kelvin.lozier

Neebick

A scabbard for my version of the Master Sword. The interior is sized for the blade with a 1mm tolerance. Should give enough wiggle room while still holding. I added a sleeve in the back of the top gold piece that can fit a standard 1.5" (38mm) belt. I hope that this will be work for anyone that wants to wear it.&nbsp;The scabbard is model after the version seen in Twilight Princess. Mostly since there are very high resolution images of it available. I plan to add different gold piece designs once I am happy with this version. A skyward sword version and a shrunken child sized version are planned.&nbsp;Printing:This model is designed for multi color printing as an option. All parts are sliced so that they are solid color through to the center. This prevents excessive color changes when an entire layer only need to be one color.&nbsp;Each section is glued together with a joiner piece. Each piece is a little different. Make sure they are put in the proper order and direction. The scabbard is slightly tapered and does get smaller the lower is goes.

Master Sword Scabbard from Legend of Zelda

long prints 

Brism_DE

Pretty minimalistic Earrings in Dagger look.

Brism Earrings Dagger

jewelry 

mail.iou

update 04/05/2024If you want a printing method that is easy to maintain, you can consider my redesign:Reverse Blade Collapsing Katana - Rurouni Kenshin<a target="_blank" href="https://makerworld.com/en/models/414234" rel="nofollow noopener">https://makerworld.com/en/models/414234</a>&nbsp;update 01/12/2024 This knife is a one-piece printed design. If you are not sure whether the filament you bought can print this work well, you can refer to my new creation &#34;Nichirin Samurai Sword&#34;. This work uses a split printing design to facilitate future maintenance and blade replacement. Nichirin Samurai Sword : <a target="_blank" href="https://makerworld.com/en/models/135353" rel="nofollow noopener">https://makerworld.com/en/models/135353</a>&nbsp;Reverse Blade Sword miniThis is a smaller version of the Reverse Blade Sword, with a total length of about 80cm, suitable for A1 mini printers or people who don’t want to print too much. If you want to experience the full size, please go to <a target="_blank" href="https://makerworld.com/en/models/111322" rel="nofollow noopener">https://makerworld.com/en/models/111322</a>&nbsp;Notice It is recommended to use PLA+ and Textured PEI Plate for printing. If the viscosity of the plate of your 3D printer deteriorates, be sure to use glue to increase the grip to prevent the printed part from falling off halfway and wasting filament.After printing, please remove the support at the end of the knife.<figure class="table" style="width:77.33%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-29_51c8c09c32f62.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-29_60e68ce20b26b.png"></figure></td></tr></tbody></table></figure>Repair of fallen blades This work has been printed and verified on P1S, A1, and A1 mini printers and resized. It is currently tested using three materials: Bambu PLA, eSUN PLA+, and eSUN ePLA-Matte. The blade surface can be freely expanded and contracted without falling off. However, since PLA material is not resistant to high temperatures, if it is stretched and swung back and forth many times quickly, it will cause the blade to be heated and expand, causing the blade to be thrown out. At this time, you can repair it with a simple method. Please use a tape with high viscosity that is not easy to fall off, such as Acetate Cloth Tape. Stick it on the entrance where the blade falls off. The amount of tape can be adjusted to increase or decrease the size of the enlarged hole. Then push the blade down and plug it back into the entrance to repair it.<figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-30_59e2edca56a86.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-30_9ae8cbf98f5af.png"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/816156/2023-12-30_75ce6d29cda6e.png"></figure></td></tr></tbody></table></figure>&nbsp;&nbsp;

long prints

jewelry

stuff to make