kansast1775

Taa Design

Imagine a unique twist on the classic game of chess—a vertical chess board designed to hang elegantly on any wall. This custom 3D-printed board features magnetic chess pieces that securely attach to the board, allowing for seamless gameplay without the worry of pieces falling out of place.&nbsp;What sets this vertical chess board apart is its practicality for asynchronous play. Perfect for office environments or anywhere colleagues enjoy a slow-paced strategic game, players can make one or two moves per day at their convenience. To keep track of the game&#39;s progress, a magnetic flag is ingeniously attached to the board, indicating who made the last move.&nbsp;This board also includes a magnetic frame where captured chess pieces can be stored. This ensures that no pieces are lost during gameplay, offering both convenience and peace of mind. I added two profiles: one with magnet holes (requiring the purchase of round 4x2mm magnets) and one without magnet holes. Assembly is straightforward but requires super glue. You&#39;ll need to glue the frame and the round magnets into the designated holes on the board as shown below. You will need approximately 98 of the 4x2mm magnets. Here is the Amazon link for the magnets I used: <a target="_blank" href="https://a.co/d/e0zGRuU" rel="nofollow noopener">https://a.co/d/e0zGRuU</a> Note: In the chessboard profile, I unchecked the prime tower to fit it in the A1 mini plate. Please make sure to wash the plate to increase the adhesion and check the Flow Dynamics Calibration option to get a clean print <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000501571/design/2024-06-19_dffebedcd3c99.jpg"> Note: I added a none AMS version of the chessboard. Glue will be required to glue the black part of the board with the white one as shown below: <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000501571/design/2024-06-24_d32f1caa3ac34.png">

Vertical Chess

chess

xerko

UNO Reverse ? No, this is UNO MIDDLE FINGER！&nbsp;Print with 0.4 or 0.2 nozzle.Each profile are available now.&nbsp;For 0.4 nozzleAt layer #4(0.8mm) swap to any color you want.At layer #5(1.0mm) swap to Black.&nbsp;For 0.2 nozzleAt layer #7(0.mm) swap to any color you want.At layer #9(0.9mm) swap to Black.&nbsp;Setting Suggestion For Both Nozzle Size：Arachne wall generator0.95 top flow rate&nbsp;Size: 56*87mm-----<a target="_blank" href="https://makerworld.com/en/models/457401#profileId-365407" rel="nofollow noopener">Double side &amp; face down version is now available here.</a>

Middle Finger Uno Card

audra

Just_Josh

This tree of life inspired piece of art will make a great mothers day gift. The image can be laid flat or propped up against a wall, or I have also included an optional stand to connect to the rear of the image so it can be displayed more easily.&nbsp;If you like what you see please check out my other work <a target="_blank" href="https://makerworld.com/en/@Just_Josh" rel="nofollow noopener">https://makerworld.com/en/@Just_Josh</a>

Mothers Day Tree of Life

boys

3DPmom

<img class="image_resized" style="width: 30.8%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000229475/design/ef01914b-e52f-46bd-9810-329db5a250f1">Gardening just got fun with this cute little carrot patch 🥕🥕 Plant it on your desk, coffee table or wherever you need some fidgeting fun.&nbsp;Dimensions of Large Carrot: collapsed 2 ½ in. x 1 ⅝ in.; expanded 5 ½ in x 1 ⅝ in.Dimensions of Small Carrot: collapsed 2 ¼ in. x 1 ⅜ in.; expanded 4 ½ in. x 1 ⅜ in.Dimensions of Bed of dirt: 7 in. x 2 ⅛ in. x 1 in.Dimensions of Planter box: 7 ¼ in. x 2 ½ in. x 1 ¼ in.&nbsp;<img class="image_resized" style="width: 30.51%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000229475/design/0095922b-c6d0-47d9-88bb-e7148aaa0185">Layer Height 0.2mmPLA works great15% InfillNo supports needed&nbsp;Note: I recommend printing the carrots on a smooth print plate (you can use a glue stick/hair spray or add an outer brim to the carrots if necessary to help with first layer adhesion.)&nbsp;Here is how I arranged my print profile (notice that on plate #5 I arranged all 4 carrots to print together to cut down on purge waste):Plate #1: Large Carrot (2 colors)Plate #2: Small Carrot (2 colors)Plate #3: Bed of dirt (1 color)Plate #4: Planter box (1 color)Plate #5: 2 Large Carrots, 2 Small Carrots (2 colors)&nbsp;“Assembly” is simple, when all the pieces are printed, simply place the bed of dirt in the planter box and add the carrots.&nbsp;<img class="image_resized" style="width: 30.6%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000229475/design/9e3b143b-5c81-450d-a2eb-a958d963461d">My designs are free for personal and non-commercial use. If you would like to sell them for commercial use, send me a message and we can discuss the details:)&nbsp;<img class="image_resized" style="width: 30.17%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000229475/design/14371598-53d9-4ddd-9638-93d796fc08b5">If you like my work and want to help support it, you can buy me a Diet Coke at <a target="_blank" href="https://www.buymeacoffee.com/3dpmom" rel="nofollow noopener">https://www.buymeacoffee.com/3dpmom</a> Thanks so much!&nbsp;Have fun printing!

Carrot Garden 

kade

agepbiz

Assembly video: <figure class="media"><oembed url="https://www.youtube.com/watch?v=6n7tGLCy-1o"></oembed></figure>&nbsp;Print in place kit-card toy. Use a pair of flush cutters to separate the parts then assemble the toy. I have included both a single color version and a multicolor version.&nbsp;The Jeep Kit Card: <a target="_blank" href="https://makerworld.com/en/models/223303#profileId-241285" rel="nofollow noopener">https://makerworld.com/en/models/223303</a> The Trailer: <a target="_blank" href="https://makerworld.com/en/models/428258#profileId-332362" rel="nofollow noopener">https://makerworld.com/en/models/428258</a>The Gun:<a target="_blank" href="https://makerworld.com/en/models/469311#profileId-378676" rel="nofollow noopener">https://makerworld.com/en/models/469311</a>&nbsp;Subscribe or follow me on: Instagram: <a target="_blank" href="https://www.instagram.com/agepbiz/" rel="nofollow noopener">www.instagram.com/agepbiz</a> YouTube: <a target="_blank" href="https://www.youtube.com/user/agepbiz" rel="nofollow noopener">www.youtube.com/user/agepbiz</a> Twitter: <a target="_blank" href="https://twitter.com/agepbiz" rel="nofollow noopener">www.twitter.com/agepbiz</a>&nbsp;WARNING: CHOKING HAZARD - Small parts Not for children under 3 yrs.&nbsp;Printsettings: No support No raft 0,16mm layer height

Trailer for the Jeep Kit Card

brian

W.drop2027

<h2>Batmobile Ⅴ Wireless Mouse </h2><h4>The fifth generation of Batman Chariots </h4>The Batmobile is an integral part of the Batman saga, and for car fans, the Batmobile is fascinating！I craeted this shape batmobile from images and clips online with lots of simplified desige to print easier.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479650/design/2024-05-30_197ba183dac308.png"></figure><figure class="image image_resized" style="width: 88.62%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479650/design/2024-05-30_2bb362afef9b48.png"></figure>This model utilizes the Hardware Kit: Wireless Mouse Components Kit-002. In addition to the shell of the wireless mouse, the core components are general Bambu wireless components Includes mouse battery compartment and baseplate namely。&nbsp;All you need is one color to assemble a cool wireless mouse on your desktop.<h4>Assembly diagram</h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479650/design/2024-05-31_0a44f9bde2a0d.png"></figure><figure class="image image_resized" style="width: 73.89%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479650/design/2024-05-31_85e739e2c8b13.jpg"></figure>In addition to the 3D printed workpiece you only need to buy an additional 5 battery.<figure class="image image_resized" style="width: 41.92%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000479650/design/2024-05-31_66da203b8bfa2.png"></figure><h3>Note: Be careful when removing the tail support of the model！</h3>

Batmobile Ⅴ Wireless mouse

wireless mouse

theracecarshop

Modular wrench organizer. Make as many as you need to organize all your wrenches.

Modular Wrench Holder

tools

parksddd

Are you neuro-spicy, like me?Do you only buy the same brand of the same products over and over, once you have found the right thing?Do you hate wasting the last drops of the previous bottle when you open a new one?&nbsp;Well, have I got the print for you.Take a few measurements, customize this bottle joiner, and let gravity do the work for you!&nbsp;You&#39;ll need 3 measurements.<ol><li>Diameter - This is actually the size of “circle” that is used to cut the threads, so I find it easiest to get a measurement by measuring from the inside of the threads on one side of the neck, to the outside of the threads on the other. See my example picture of a 26mm diameter.</li><li>Pitch - This is the distance between threads. See my example picture of a 4.5mm pitch. 3 and 4.5 are very common.</li><li>Height - This should be a little bit shorter then the length of the threads multiplied by 2. This one can be a bit fuzzy, you just need enough height to catch threads on both bottles to screw them together.</li></ol>Works with every bottle I&#39;ve thrown at it.It will also print the stats on the outside of the model, in case you need the details in the future!&nbsp;Default values:Diameter 20 Height 20Pitch 3

Bottle Joiner

generative

Angelol

Designed for my machines!&nbsp;Print with the X face on the bed, no supports needed

1:64 display ramp "x" face

1/64 scale

Filamaze

Hi,&nbsp;Sunlu/Geeetech spool don't work with the new AMS lite so I made my own adapter for them ! Easy to print !this will make all your sunlu/Geeetech spool work on the AMS LITE ! &nbsp;**UPDATE V3** now print fast since its shorter and easyer to print !&nbsp;Enjoy printing :) &nbsp;If you like this model, please like it, rate it and follow me ! If you have any recommendation I will update it with different version number :) &nbsp;Go see all my other work ! &nbsp;Thank you

Sunlu/Geeetech AMS Lite Adapter ** UPDATED  **

printer A1

BamBam Design

<h4>The Honeycomb Windmill - Self adjusting hexagon turbine</h4><a target="_blank" href="https://youtube.com/shorts/8R5ItdJsFic?si=613GcVD2ep95zNK6" rel="nofollow noopener">YT Short Action </a><ul><li>Beautiful Windmill with a unique honeycomb Propeller Design</li><li>Self adjusting to wind direction through the Tail Blade</li><li>100% printed, no Screws or tools needed</li><li>You can add 3 Propellers on one Axle with 2 distances</li><li>Use different propeller sizes and directions (You get nice effects if you choose different directions) </li><li>Rods are stack able to your needed height</li></ul><h4>Printing:</h4>&nbsp;The rod could be a bit difficult to print, i added custom support, but clean your buildplate and apply some glue.&nbsp;Profile is tested with PETG &amp; PLA 👍🏼<h4>Assembly:</h4><figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=1oeRMYjatbI"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/1oeRMYjatbI" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure> Thanks to all followers and don&#39;t forget the virtual handshake 👍 ….Happy Printing&nbsp;Info:My other windmills are fully compatible if you want to mix it up:<ul><li><a target="_blank" href="https://makerworld.com/models/235261" rel="nofollow noopener">Toroidal Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/250216" rel="nofollow noopener">Honeycomb Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/388124" rel="nofollow noopener">Elliptical Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/425419" rel="nofollow noopener">Sunflower Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/454861" rel="nofollow noopener">Raccoon Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/255324" rel="nofollow noopener">CLAMP for Windmills</a></li></ul>&nbsp;You can combine propeller blades with Toroidal Windmill: <a target="_blank" href="https://makerworld.com/models/235261" rel="nofollow noopener">https://makerworld.com/models/235261</a><a target="_blank" href="https://makerworld.com/models/235261" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000250216/design/2024-03-08_e93cd56771b2.gif"></a>Checkout this Clamp for windmill, as well🧐 <a target="_blank" href="https://makerworld.com/models/255324" rel="nofollow noopener">https://makerworld.com/models/255324</a><a target="_blank" href="https://makerworld.com/en/models/255324" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000250216/design/2024-03-15_6d9c46a2c3e8c.jpg"></a>&nbsp;Commercial license you can get here:<a target="_blank" href="https://www.patreon.com/BamBamDesign/membership" rel="nofollow noopener">https://www.patreon.com/BamBamDesign/membership</a>

Honeycomb Windmill - Hexagon Wind Turbine

Neopyx3D

A cute articulated Fennec created to participate in the Animal Frenzy design contest.&nbsp;This model is: PRINT IN PLACE - NO SUPPORTS&nbsp;Testprinter: A1 Mini with a 0.4mm nozzle printed in multicolorFilament for the Testprint: ISANMATE Highspeed PLA coffee (body), Filament Unger anthracite silver (eyes and nose)&nbsp;This download is for personal and non-commercial use only. Don´t sell my designs or printed designs without permission.If you want to sell your 3D-printed Neopyx3D designs you need a Neopyx3D - Vendor membership via Patreon:&nbsp;https://www.patreon.com/Neopyx3D&nbsp;Recommended Main Settings:&nbsp;Layer height: 0.16 Infill: 15 % Gyroid Supports: No Supports needed Build Plate Adhesion Type: Brim (optional if you have adhesion issues) Printing Temperature and Cooling: depends on filament

Articulated Fennec

toys

OscarTheCat

My first attempt to design a yarnbowl&nbsp;tree prescaled sizes at 15 / 17 & 20 cm &nbsp;printed mine at 13cm.&nbsp;feel free to scale it as you like.

Yarn Bowl

yarn bowl

Fin3dPrinting

This is a Desktop Skee-Ball Set! This Prints in 3 parts, the top, the alley, and the under-top part (for the ball retriever). You can use any glue to assemble it like superglue or 3d gloop PLA (recommended) Link For 3d Gloop <a target="_blank" href="https://www.3dgloop.com/shop/pla-gloop" rel="nofollow noopener">https://www.3dgloop.com/shop/pla-gloop</a> (optional)For the marbles, I used Glass Sling Shot Ammo which works very well and fits perfectly. You can find it at your local hardware store. Regular marbles should work. The diameter of the holes is about 13.5 mm. The slingshot ammo is 13 mm in diameter and it works perfectly fine. i also added a model for a ball located in the raw model files if you need it!One part is printed with 2 colors (the top cover) No need for any ams. All you have to do is switch the colors at layer 16.See it in action! <a target="_blank" href="https://youtube.com/shorts/sGEPZCtA37E?si=al30t8tzI95TXrX-" rel="nofollow noopener">https://youtube.com/shorts/sGEPZCtA37E?si=al30t8tzI95TXrX-</a>Print settings-Supports- Yes, Tree Organic, 30, on build plate only.Brim- NoInfill- 10-15everything else NormalAssembly Instructions-1- glue the alley and the undercover together<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000156243/design/2024-01-25_6a534f3377ae.jpg"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000156243/design/2024-01-25_877860f8d7bae.jpg">step 2-Glue on the top cover<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000156243/design/2024-01-25_81df1f9fa841c.jpg">All done!!Good Luck!!Visit My shop at <a target="_blank" href="https://fin3dprinting.etsy.com" rel="nofollow noopener">https://fin3dprinting.etsy.com</a>&nbsp;&nbsp;

Desktop Skee-Ball Set- BALL RESET-Fun-Desktop-Desk

maegu_

Hummingbird Silhouette Wall Art&nbsp;The Flower to this can be downloaded here : <a target="_blank" href="https://makerworld.com/de/models/99403#profileId-105975" rel="nofollow noopener">https://makerworld.com/de/models/99403#profileId-105975</a>&nbsp;

Wall Art - Hummingbird Silhouette

hueforge

StickMan

How many Benchy models do you have? Do you need to organise them?Great!Print the holder, put your Benchy in it. It'll fall over. Print the base. Clip it in. Job done.More than one Benchy? Print another holder and base. Print the joint and connect them together.Want to stack them higher? Print the top joint and stack them up.Bored with just a straight line or flat display? Print some 15 or 30 degree joints and mix it up with some curves. Make a half cylinder or a full cylinder. Have some fun!&nbsp;The ‘Offset’ configuration allows you to offset the rows by half a module so that you can squeeze a Benchy in the middle on the second row instead of having to skip a row. This only works for the 30 degree joints.&nbsp;Tips:The joints are best printed single skinned in vase mode, which is great if you have the time. The print profile prints single walls but ‘per layer’ to the end result might not be quite as good. This does allow you to print all the joints you need all in one go.For extra strength when assembling, print a half height joint, put it on the end, then for the next row add a full height joint to straddle the gap between layers. The top joints don't offer much friction and are intended as guides.Benchys can fit in the holder both ways, however it's intended that they are horizontal when pushed in correctly.

Modular Benchy Holder Display Stand

benchy

maruel

I&#39;ve seen a few 2&#34;/2.5&#34; mini hitches on makerworld and decided to create my own from scratch with the following features:<ul><li>Round parts (bolt, pin and clip) are 100% round by standing upright.</li><li>No glue is required. Assemble and you&#39;re done.</li><li>It&#39;s a real M6.6x1.5 screw! Tolerance is very tight, you&#39;ll have to use a real wrench to tighten it.</li><li>Minimal use of supports, only the bolt needs supports. Clever use of mini supports on the base.</li><li>Optimized for minimal filament use. The pin and base are completely hollow and do not need supports. Only 53g in total!</li></ul>The model is split on 4 plates to make it easy to print in 4 colors. I used Bambu PETG Basic Gold, Black, Gray and Red. Designed to be printed in PETG. You can print in PLA but the colors will fade within a few months.

Small 2"/2.5" mini hitch; real screw and no glue

practical

kodikat

<h3>Project Introduction</h3>This lamp was designed to allow people to try various techniques when printing Translucent PETG filaments. The shade and lamp body parts are easily interchangeable allowing the light to have a variety of styles and is a great platform for remixes.&nbsp;<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=ImjrlrFhTjk"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/ImjrlrFhTjk" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>Bambu Wiki for printing Translucent PETG : <a target="_blank" href="https://wiki.bambulab.com/en/knowledge-sharing/transparent-petg" rel="nofollow noopener">https://wiki.bambulab.com/en/knowledge-sharing/transparent-petg</a><h3>Community Designs</h3>As I was designing this lamp, I tried to design it to allow for modularity and allow for creative modifications. I would love to see other peoples ideas and how they paint the prints. For all the “stained-glass” parts I included them unpainted so that I do not stifle any creativity. There is a section below where I will outline some ideas that I had but didn't have time to design or print.<h3>Bill of Materials</h3><ul><li>3x ~11 cm long LED Strips - The model is designed to allow up to 12mm wide LED strips, I chose to use the LEDs shown below so I could power them easily via USB. I would suggest LEDs on the warmer spectrum. <a target="_blank" href="https://www.amazon.com/gp/product/B0CDKXN3T3/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1" rel="nofollow noopener">https://www.amazon.com/gp/product/B0CDKXN3T3/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1</a></li><li>~100 cm 22 AWG Wire</li><li>Some Way to connect to power, I used these premade USB power leads, but there's a lot of options here. <a target="_blank" href="https://www.amazon.com/gp/product/B09FF883CX/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1" rel="nofollow noopener">https://www.amazon.com/gp/product/B09FF883CX/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1</a></li></ul><h3>Printing Suggestions</h3>Filament: PETG Basic, PETG Translucent&nbsp;I used all Bambu filaments other then some prototyped pieces when I ran out of black PETG and Bambu was on break so I used Black Overture PETG.&nbsp;Before printing, I suggest you use some sort of tolerance test to make sure you can print your PETG to 0.1 mm tolerances with no problem. I was able to do this test without any special settings or changes to my X1 Carbon. Many parts are friction fit to allow for interchangeability.&nbsp;A majority of the pieces are rather trivial and designed to be printed without support. With that said, the shade pillar sides will test your overhang printing abilities. I used minimal tree supports to keep the print upright, but allow greater airflow from the part fan. If you do not slow printing speed down and possibly increase your part fan on overhangs, the overhangs might not cool fast enough and create an ugly print. I will say in all my testing, I always came out with useable parts, but not always pretty parts.<h3>Assembly Instructions</h3><figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=8rMZSCH8kEk"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/8rMZSCH8kEk" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>I hate long videos, feel free to watch this at 2x speed :)<h3>Ideas for Improvement or Remixes</h3>As with any project with a deadline, compromises have to be made. As I went I realized there were areas for improvement or experimentation. I tried to note as many as possible, but this list might grow as I come upon ideas.&nbsp;I would like to release a version 2 at some point to include these ideas, but would also love to see others join in and share their ideas. Whether they are for better functionality, or a different aesthetic.&nbsp;<ul><li>Lithophane sides - These could be images, but I did some preliminary experiments using images of rocky or marble textures with the translucent PETG. This created some of the variation you might see in normal stained glass. Pair this with the printing profiles from Bambu and you could end up with some awesome results</li><li>3-Way Light Switch - Would've loved to incorporate a spot on the base for a switch as linked below, but also note this would require structural changes to parts to allow for the additional wiring. The idea is you have a switch that turns the bottom on, the top on, both on, or both off.  <a target="_blank" href="https://www.amazon.com/Lamp-4-Position-Circuit-Rotary-Removable/dp/B01LYCHAMM/ref=sr_1_3?crid=24IFG1HEL32LQ&dib=eyJ2IjoiMSJ9.LYgMkksbf62ehrAyz66HhhZahFGFGtNSqSybBDv2qV1z87747FqvwrrLOXZfwc3U3GqYmPGtcipN7ttDg64OHNsthGOk4ZPX3uCwjgYdQ2ic3io60wga_5Ec4dLziBuALOn9h9LrS9t1XzpTkLxMtNKJVeX-JE7LV33l3W4o2IJQr3JJsBSScJ6eH-yWVvDVfrK95_Hv5gUAhnbzO1aYelHiOQV5F4Wunnzmmyg4NkkedDI-OxIBMQE9ihCmFbgsV1EdeTUo6VwBZId2bBbvfQy4HYs0mR9XAVowVsasdEg.rRgQT3LVtPjMEQduk6OcH3Dc5SX5f3P9u-hynFYGjh4&dib_tag=se&keywords=3+way+light+switch+twist+lamp&qid=1708215977&sprefix=3+way+light+switch+twist+lamp%2Caps%2C113&sr=8-3" rel="nofollow noopener">Switch link</a></li><li>A middle pillar for the base with no light and no shades, could be some cool designs here</li><li>TPU Gaskets - There are a few places to add gaskets that I think the positve pressure would help hold the screws in place</li><li>Base designs - Below I will put some basic dimensions so that it would be easy for anyone to make their own designs for the base. Even beginners could design a neat base that makes the lamp completely theirs!</li><li>Pretty obvious, but other shade designs!</li></ul><h3>Stained Glass and Base Dimensions</h3>The following dimensions should help when designing custom panels for the shade and body side panels. The side panels simply slide in, but the shade does have bumps that allow the pieces to snap together. While you could omit these and glue the shade together, you wont be able to every change the shade panels without printing a whole new shade.<h4>Shade</h4>In the raw files, I uploaded STL, STEP, and 3MF files of a plain shade side. There is a back and a front. How I designed my shade was I drew the design on the shade front, extruded to cut holes in the front. Then I projected the sketch to the back color piece, offset the sketch by 0.1 mm, then extruded forward. If this explanation doesn't help, comment and I will make a quick video.&nbsp;I thought this approach was easier for this piece than providing dimms.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/557443/2024-02-19_b4339558106b8.png"></figure>If you prefer not to do a 2 piece approach, I also uploaded the files for a single piece that you can do whatever you want with. It is also in the raw files.<h4>Bottom Stained Glass</h4>I hope these dimms help expedite any remixes. I can do some raw files with no design like above if  requested, I just figured since it is simple shapes this might be easier to start from. &nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/557443/2024-02-19_b64535da10daf.png"></figure><h3>Change Log</h3><h4>02-19-2024</h4><ul><li>Added Printer profiles to the raw files for glass like prints. I haven't printed these yet because I broke the thermistor when swapping nozzles and I have to wait for new ones to come in. Once I have tested each, they will be added as print profiles. These profiles are just bambu's suggested settings with the shade and bottom color piece on a plate. I am not sure when I will be able to test, so I wanted to make them available.</li><li>Added files for the plain shade in the raw files, and added image with dimmensions for the bottom stained glass pieces. </li></ul>

Customizable Stained Glass Lamp

lights

Ryan

I took the original models and shortened the handles by about 50mm and reduced the handles to only need 2 plugs. I also reduced the blade size by about 40mm.&nbsp;The uploaded profile has 3 plates optimised for an A1 mini and gives you all the tools and about 68 screws (a mixture of small and large).

Cardboard Maker Tools for kids

sellable

SavageLau

<h2>If you want a commercial license, check out my bio and get it from Patreon.</h2><h2>Personal use only.</h2>&nbsp;This model is design for MakerWorld light contest (2/5). Complete free version is only available on here Makerworld. <h3>Many people have contacted me said they willing to pay for the model. Other platform product manager reach and out said I could use their platform and selling this design for some money, but I have decided to keep it here for free for now. So there will be more people could enjoying it :) So show me your finshed print, I would like to see it. </h3><h3> Anywhere else you see this model upload is Unauthorized (please notify me and report them), beside my own account (SavageLau). </h3>&nbsp;<h2>If you would like purchase LED light needed for this design and filament from Bambu Lab Offical website: Affiliate link is below, so I can get some commission to support my future work. </h2><h2><a target="_blank" href="https://shrsl.com/4h4np" rel="nofollow noopener">https://shrsl.com/4h4np</a> </h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-03-23_4ad27b7082fe3.png"></figure><h2>Filaments that I use for this project: (Bambu Lab Offical website:)</h2><h2><a target="_blank" href="https://shrsl.com/4h4ns" rel="nofollow noopener">https://shrsl.com/4h4ns</a> </h2>&nbsp;&nbsp;&nbsp;<h2>You may also like this design:</h2>PeaShooter Lamp Kit 001. <a target="_blank" href="https://makerworld.com/en/models/174475#profileId-191833" rel="nofollow noopener">https://makerworld.com/en/models/174475#profileId-191833</a> &nbsp;&nbsp;&nbsp;My boss saw some Bellsprout light the other day and she want me to design one. I have one LED Lamp kit come with my a1mini and sitting for a while. So why not turning it into what she want. So the design started adpot the lamp kit into Bellsprout.I found this pic on Google, based on the posture and proportion started deisng.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_bc131748fd272.png"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-01_33679f29d502a.png"></figure><h2>Update: </h2><h3>2/2/2024. A new profile was made for a1mini. Increased infill/walls on base and body part. </h3>Model main body have been reduced in size inorder to meet the build plate size for a1mini with muti-color prints. &nbsp;<a target="_blank" href="https://makerworld.com/en/u/2010665163" rel="nofollow noopener">@Sascha2202</a> feedback it is a bit hard to keep banlance. Weight increased on printing profile by adding more infill and walls. Weight for that part from 160g to 202g, lowered center of gravity. Consider head is around 40g + led weight, it should do well now. <h3>2/1/2024. Joints redesigned. </h3>Improved joints firction load, strength, tolerancing. New turning angle sets around 13.5 degrees max for each joints. <figure class="image image_resized" style="width:36.72%;"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-01_d00693a8b7acb.png"></figure>“Head” part fit and finish improving. <h3>Revisions and Tests today:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_ffe7e41994dec.png"></figure>&nbsp;<h2>Before you print(Important!):</h2>Run the joint test print first with the filament you are going to use for joints and body, before you doing the full print! This is important. Depend on filaments you use for the joint parts, there will be sinkage rate difference, and firction load on joint will be different.&nbsp;I put very tight tolerancing on design, but it may not work as intended when you printing with your filaments, so run the test and confirm joints is very tight to each other. Other wise You will not get the desired result.&nbsp;&nbsp;Joints with other parts are standard size. There is one “Tight” profile for joints. There are two types of joint, regular and with wire clip one. You will need to print total of 12 or above (maybe less than 15) to get good proportion. &nbsp;Joints designed best work with 4 wall layers, and 10% to 20% infill, adding more infill will not improve the strength, will only leading part failure during assembly. &nbsp;<h2>Hard ware:</h2>This design require Lamp LED Kit 001 from Bambu Lab. All other parts are printable. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-31_bca061fd80f1d.png"></figure>&nbsp;<h2>Post work:</h2>Removing brims from all parts, when you remove brim from joints part, confirm it is fully removed. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_dec1b2c670225.gif"></figure><h2>Assembly:</h2>Refer these gif image. Joints is a bit hard to push in, refer how I do it, holding the bottom part with you fingure, it will reduce the change of failure. &nbsp;Joints:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_5c978e23e8634.gif"></figure><figure class="image image_resized" style="width:51.25%;"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_9f2e463b2d8a6.gif"></figure>Fully assembly:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-02-02_9a975d341b61f.gif"></figure>&nbsp;&nbsp;&nbsp;<h2>Design:</h2>Lamp kit is 60mm dia, 8mm thickness. based on that dims and make rough draft to evaluate the overall size.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_34bf66e6b20e5.png"></figure>&nbsp;Working on some parts, and integrate them in the end.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_4880a9ab2336a.png"></figure>&nbsp;I started with wanting ball joint on the head, so it will able to turn angles. End up why not to have more ball joints on the body.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_b08f0ea2e5ee9.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_80ec7f991cbaa.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_80ed16d7dd498.png"></figure>&nbsp;Ball joints is pain in the axx to work with. I want it to have a lot of friction load in normal condition. so the outter shell shall have very small tolerance to the ball or even smaller. Ended spending a lot of time try in truth to testing out different tolerances and make design revisions.Still not perfect, but it work for this application. You gain a lot of DOF, but it is a bit brittle, depends on your materials.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-30_153933e0ba5bb.png"></figure><h2>Revisions and tests:</h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/796346/2024-01-31_641c974fd0d58.png"></figure>

BellSprout Lamp LED Kit 001

characters

gogo3D

funny bathroom sign

sign

FoxPrint3D

Baby crystal Dragon

dragon

PenolopyBulnick

With this pair of earrings, I used <a target="_blank" href="https://www.craiyon.com/" rel="nofollow noopener">Craiyon.com</a> to give me a grunge stained glass flower design. I did only minor edits to the design before running it through <a target="_blank" href="https://shop.thehueforge.com/" rel="nofollow noopener">HueForge</a> and messing around with colors and layers. &nbsp;Use two jump rings and an ear wire for each flower. &nbsp;Color Changes: Layers 1 - 12: BlackLayers 13 - 15 : Blue (Inland) - I actually prefer another blue, that looks like more of a grey/blue next to the other blue,I have but it's discontinued and I'm unable to find anything similar. Layers 16 - 18 : Magenta (Inland) Layers 19 - 22 : Silver (Matterhackers)Layers 23 - Top : White&nbsp;<ul><li>.08mm Extra Fine settings were used with .4 Nozzle.</li><li>Ironing on all top layers.</li><li>Gyroid infill is used where it is necessary but 100% infill could also be good with how small and thin it is.</li><li>I use a Prime Tower, but it is small. Possibly not necessary but helps sometimes.</li><li>4 colors</li></ul>