jsvojtka

EEEEEE

This project is the culmination of 100+ hours of remodeling and printing. &nbsp;There was no miniature handheld glider that could be printed and thrown straight all in less than a half hour, which I wanted to change&nbsp;The main features of the glider are its unparalleled accuracy and consistently, allowing a skilled used to soar the plane 30 feet before it lowers by even an inch. &nbsp; Pitch Stability     Yaw Stability     Ease Of Use     Consistency      Durability       Airtime           ★★★★★          ★★★★★         ★★★★         ★★★★★          ★★★        ★★★★★&nbsp;This was printed on the Bambu P1P and printed in 23 minutes(17 minutes of actual printing) with white PLA basic. It used just under 10 grams of filament.Instructions-Print in PLA at 100% infill with no brim or raft. Wait for the hotbed to cooldown before gently using a scraper tool to remove the glider.<figure class="image image_resized" style="width:31.52%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000083624/design/2023-12-05_h3ph93i1hm0i.jpeg"></figure>Bend the tail segments up 90 degrees.<figure class="image image_resized" style="width:31.52%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000083624/design/2023-12-05_rtzdaumbtly8.jpeg"></figure>Bend the elevators down about 25 degrees, and flip over the plane.<figure class="image image_resized" style="width:30.98%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000083624/design/2023-12-05_ll74i2pc6mdz.jpeg"></figure>Hold the glider from between the main and tail wings, and throw lightly. The tail segments should be facing downwards when thrown, and the elevators should be facing up. If the plane seems to lean to one side, try to throw the plane with more power.The design fits on most build plates if positioned diagonally, but if it doesn&#39;t fit, print Left Simple Indoor Glider V2 and Right Simple Indoor Glider V2 separately and glue them together with hot glue or a 3d pen. Tape or rubberbands could also work.You can reverse the tail wings if you want the plane to look better and land more smoothly at the cost of slightly worse performance. Just make sure the weight on the front of the plane is facing downwards to increase stability.

Simple Indoor Glider V2

Modely

Nico91

<h2>BMW M Logo Lightbox.</h2><h2>For best results use this profile.</h2>Bambu Studio Settings1. First Layer Flow Ratio: 1.08. (Developer settings). 2. Wall generator → Arachne. 3. Set Quality → Wall transitioning threshold angle to 50º. 4. In Strength → Advanced, adjust Infill/wall overlap to 20% to 25%. 5. Quality → Advanced → Activate "Avoid crossing walls." 6. Order the colors from the lightest to the darkest.7. First layer speeds, 30mms and 60mms for first layer infill.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/292830/2023-12-21_a67b5ebe40f2e.png"></figure>

BMW M Logo Lightbox LED Lamp

c4444

A simple hook designed for 10mm thick glass shower screens.&nbsp;+NEW UPDATED MODELS;&nbsp;New ‘Stackable’ versions available. Allow you to add multiple hooks together into one unit (with optional spacers between) via simple built-in push fit connectors.<ul><li>Stackable version for 10mm glass Left Hook</li><li>Stackable version for 10mm glass Middle Hook</li><li>Stackable version for 10mm glass Right Hook</li></ul>Spacers for stackable versions;<ul><li>Stackable version 20mm wide spacer</li><li>Stackable version 10mm wide spacer</li></ul>Also version for 6mm glass screens;<ul><li>Non Stackable version for 6mm glass Hook</li></ul>

Hooks for Glass Shower Screen - multiple types

Koupelna

rschmid5512

Two color version side plates of <a target="_blank" href="https://makerworld.com/en/u/2567999635" rel="nofollow noopener">https://makerworld.com/en/u/2567999635</a> by 3DMON maker.

AMS Tall Stand V2_2 Color

3DPODesigns

UPDATE: Per requests in the comments, I've added a way to add weight to the Hex Paper Towel holder if you find it necessary. You do NOT need to reprint the paper towel holder itself. Simply print the “Hex Paper Towel Holder Plug” profile, fill the hollow portion of the paper towel base with sand/dirt/or weighted material of your choice and press fit the plug into the hollow hole in the base(I was able to add 150 grams of sand to mine). Make sure you leave enough room to push the plug down far enough to sit flat. I've included a small grip on the plug for ease of guidance, as well as removal with pliers if you ever feel the need. From my testing it does not need glue, but if you want it 100% permanent, please add a dab to the sides of the plug before inserting. Pictured below is the plug assembly,<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/381832/2023-12-16_d456b79522b16.png"></figure><ul><li>This is a beautiful, functional, low filament using paper towel holder I designed for my own home. Using hexagons I've made this paper towel holder both strong and light using only 135 grams of filament and NO supports!</li></ul>&nbsp;<ul><li>Specifically sized to be printable on the A1 Mini!</li></ul>&nbsp;<ul><li>Keep in mind this model is again, light, so you may need to hold it while removing a paper towel. However, I found with even my own metal holder at home I still had to do that 90% of the time, so the filament savings seemed like a worthy trade off.</li></ul>&nbsp;<ul><li>This paper towel holder should fit most small to large rolls (though I've only tested a few I have access to)</li></ul>&nbsp;<ul><li>I've included both Default Speeds and Normal profiles as my testing with PLA at Default Speed settings was great, but if you want to print in PETG it can have flow issues, so just make sure your flow rates are tuned if using the fast profile. I strongly urge you to use the normal profile if you are unsure of your flow rates. I do not have a tuned profile for A1 mini, but I've included a fast profile that should work fine as long as your flow rates are tuned. Please let me know if you have any issues with it (I printed both the fast and normal profiles a total of 5 times each, but your experience matters!) and feel free to upload your own A1 profiles!</li></ul>&nbsp;<ul><li>If you enjoy this model please toss it a like!</li></ul>&nbsp;&nbsp;

Hex Paper Towel Holder

Kuchyň

Howell

This is an optimized version of Mandalorian Helmet for people with slight bigger head or nose (like me :) )It is scaled 1,20% bigger and still mantain optimized supports.Print speed are 300 mm/s for all internal a slower for external, I suggest to turn off AUX fan or just put slow to avoid any kind of parts with different aesthetic results.Attached are file to print it in separate parts and optimized 3MF for the accessories (speed have been slowered down due to side parts fallen down when using creator profile).&nbsp;This is the way!&nbsp;FYI: PLA is from Azurefilm, Silk Graphite Grey&nbsp;&nbsp;Update 10/21/2023: Added Print profile for accessories

Mandalorian Helmet - Big size 

Cosplay

ventar

The box can hold up to 50 9mm rounds. &nbsp;<h3>Files</h3>The files are split into 3 folders for the common part which is used regardless of the number of colors and a seperate folder for the single color and multi color box. Please be aware that the models with two colors are slightly different to ensure that there at least two printed lines for the second color. Use the single color files if you do not want to have two colors instead of using the multi color version with just one type of filament.<h3>Remixes</h3>The box was designed in Tinkercad to allow everybody to adjust it to individual needs, online, without deep knowledge of 3D construction :). Feel free to change whatever you want (none-commercial) and post a picture.&nbsp;<a target="_blank" href="https://www.tinkercad.com/things/6H2MQP234NW-9mm-box-v5-single-color" rel="nofollow noopener">https://www.tinkercad.com/things/6H2MQP234NW-9mm-box-v5-single-color</a><a target="_blank" href="https://www.tinkercad.com/things/ffwlGOf8Zlt-9mm-box-v5-multi-color" rel="nofollow noopener">https://www.tinkercad.com/things/ffwlGOf8Zlt-9mm-box-v5-multi-color</a><h2>Assembly</h2><h3>Magnets</h3>To make the lid open and close in a way, that it stops every 5 rounds, you can add magnets of 2x3mm into the prepared holes of the box. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244655/2023-12-07_58bcc5ba9b153.png"></figure>&nbsp;In combination with the wholes in the lid, <figure class="image image_resized" style="width:50.19%;"><img src="https://makerworld.bblmw.com/makerworld/draft/244655/2023-12-07_21b3165a548c8.png"></figure>this will allow you to ‘feel’ when the next 5 rounds can be distributed to your hand. &nbsp;The lid itself is hold in place with 8 additional magnets. 4 of the have to be glued to the lid<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244655/2023-12-07_57004cbb8c255.png"></figure>&nbsp;and the other 4 to the top inlay<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244655/2023-12-07_94ef03c6d5b8a.png"></figure>&nbsp;Be careful and check the correct orientation of all magnets so that they attract each other.&nbsp;I suggest to super glue the magnets and afterwards the inlay into the bottom box. This will allow everything to stay in place. I usually buy them on aliexpress in larger batchers&nbsp;Example: <a href="AliExpress" rel="nofollow">https://www.aliexpress.com/w/wholesale-magnet-2x3mm.html</a>&nbsp;You can of course use other magnets and adapt the holes in the design. You will need 2 of them inside the bottom box, which is the reason for the larger space there. To avoid buying multiple sizes this is the easiest way:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244655/2023-12-07_511e56615ffd8.png"></figure>&nbsp;Order&nbsp;The inlays and the box are glued together. Start with the box, the bottom and the mid inlay and use super glue to keep everything in place. You can choose between 2 bottom versions, where one will allow you to stack the boxes due to the little ‘feets’ that are under the box an the other without that. Afterwards add the magnets to the box and to the lid. When the glue is dry, you can add additional glue to the top inlay and add it to the box.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/244655/2023-12-07_3ecb16da1fb1b.png"></figure>Logos and Resin&nbsp;The logos on the photos are covered in resin, that you can buy easily in various shops. &nbsp;Example: <a target="_blank" href="https://www.amazon.de/dp/B0829XD6FY?ref=ppx_yo2ov_dt_b_product_details&th=1" rel="nofollow noopener">https://www.amazon.de/dp/B0829XD6FY?ref=ppx_yo2ov_dt_b_product_details&th=1</a>&nbsp;The simple ones are printed with PLA and the AMS, the coat of arms was printed on a regular laser printer and glued to the inlay before the resin was applied. The design of the 3D printed logos was made by&nbsp;https://mohrismore.com/

Magnetic 9mm Ammunition Box

Táta

glenngri

My take on a Bambu Lab X1 Carbon inspired LED light box&nbsp;Setup for a AMS and 3 colours&nbsp;LED Used should be 1m<a target="_blank" href="https://amzn.to/46iIbBn" rel="nofollow noopener">https://amzn.to/46iIbBn</a>&nbsp;Let me know your thoughts :)

Bambu Lab X1 Carbon inspired LED light box

Jáša

Chester3D

&nbsp;IntroductionThe original model is designed for printers with a 250x250mm bed.&nbsp;If for any reason it doesn't fit on your bed, you can resize the model to the size you want from your slicer.&nbsp;It consists of two parts, the lamp body (body.3mf) and the rear cover (lid.3mf).Sometimes I include two lids, with and without a hole (choose the one you want, I recommend printing the Lid with hole whenever possible, to be able to remove the LED cable).&nbsp;If the back cover does not have a hole, you can easily make it from Bambu Studio, or from any other slicer you use.&nbsp;&nbsp;&nbsp;You will need<ul><li>Textured PEI Sheet: <a target="_blank" href="https://eu.store.bambulab.com/products/bambu-textured-pei-plate" rel="nofollow noopener">https://eu.store.bambulab.com/products/bambu-textured-pei-plate</a></li><li>- LED Strip (with switch): <a target="_blank" href="https://s.click.aliexpress.com/e/_DEoEO2L" rel="nofollow noopener">https://s.click.aliexpress.com/e/_DEoEO2L</a></li><li>- LED Strip (without switch): <a target="_blank" href="https://s.click.aliexpress.com/e/_DekFgj1" rel="nofollow noopener">https://s.click.aliexpress.com/e/_DekFgj1</a></li></ul>Optional, but recommended:<ul><li>Aluminum tape: <a target="_blank" href="https://s.click.aliexpress.com/e/_DEPgqHd" rel="nofollow noopener">https://s.click.aliexpress.com/e/_DEPgqHd</a></li><li>- Glue gun or Tape</li></ul>&nbsp;&nbsp;Assembly instructionsYou can follow either of these two videos to assemble the lamp. It's very simple, you stick the LED strip inside and that's it. If you want, you can use aluminum tape to improve the lighting, although it is not necessary: &nbsp;<ul><li>Assembly instructions by braga3dprint: <a target="_blank" href="https://www.youtube.com/watch?v=QNsShLmXYh0" rel="nofollow noopener">https://www.youtube.com/watch?v=QNsShLmXYh0</a> (He makes very beautiful designs, you can leave him a follow and help him grow his channel!)</li><li>- Another assembly instructions: <a target="_blank" href="https://www.youtube.com/watch?v=nDUlBp7Mm1c----" rel="nofollow noopener">https://www.youtube.com/watch?v=nDUlBp7Mm1c----</a></li></ul>&nbsp;&nbsp;Printing settingsFollowing recommendations, you can start with these settings in Bambu Studio:<ul><li>Preferences (CTRL + P) → Activate developer settings → Quality → Advanced → First Layer Flow Ratio: 1.04</li><li>- Quality → Wall generator → Arachne</li><li>- Quality → Wall transitioning threshold angle → 50 degrees</li><li>- Strength → Advanced → Infill/wall overlap → 20%</li><li>- Quality → Advanced → Avoid crossing walls</li><li>- Increasing retraction / reducing temperature can help reducing wisps</li><li>- Order color printing from lightest to darkest color</li></ul>&nbsp;Important! Additional tips Remember to remove the purge line at the start printing, otherwhise it will ruin the print.Adjust the sequence of colors from Light colors to Dark colors, to prevent stringing. &nbsp;

Fortnite LED Lightbox Lamp

Honzík

NUKDDD

Spread holiday cheer this year with this cute little fudge wearing Santa hats! One is an ornament, the other is a dust collector, but both make great gifts this holiday season. Give a FUDGE!&nbsp;Filaments used: Bambu basic black, red, white and R3D chocolate.&nbsp;The column stand can be found <a target="_blank" href="https://makerworld.com/en/models/62436#profileId-65008" rel="nofollow noopener">here</a>.&nbsp;4 color AMS print, no supports, the more you print at once the more you save on filament and time. &nbsp;For the culture!

Happy Holiday Christmas Fudge Ornament

Ozdoby

Mr_Grizzl

HSW craft knife - scalpel Holder&nbsp;<ul><li>0.20mm Layer high </li><li>PLA</li><li>2 walls</li><li>15% Infill </li><li>no supports </li></ul>Das messer ist hier zu haben : <a target="_blank" href="https://www.amazon.de/dp/B07L5HZ1GK?ref=ppx_yo2ov_dt_b_product_details&th=1" rel="nofollow noopener">DealKits Skalpell Set</a>The handle of the knife is 8 mm thick&nbsp;

HSW craft knife - scalpel Holder

nástroje

laisch

Low Profile Spoolholder for sidemounting to the bambulab AMS. With the bowdenconnector it adds just 34mm to the AMS in width. Fits spools from 140 to 200mm diameter. It mounts to the AMS with just clamping force, so there is no need to make any changes to the original hardware. Never unplug the AMS again when printing from an external spool.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_n6cdbyuzuuve.gif"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_ajymv5zke7nc.gif"></figure>&nbsp;<blockquote>IMPORTANT NOTE: Before you print any part, read the Info part at the end of the build instruction!</blockquote>&nbsp;External Hardware:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_gpinzpf1se9r.jpg"></figure><ul><li>4pc - EXT5.55x25.4 tension springs or as an alternative 4pc small hair rubber band</li><li>4pc - M4x20 screw</li><li>5pc - M4x16 screw</li><li>9pc - M4 hex nut</li><li>9pc - M3 bras heat inserts</li><li>1pc - M3x6 screw</li><li>8pc - M3x4 screw</li><li>4pc - 608 rollerscate bearing</li><li>1pc - ptfe tube</li></ul>&nbsp;Print instructions:All parts print without supports!Everything can be printed in PLA, except the rollers should be printed in TPU. If you have no TPU, I added a PLA version for the part also. You can't just print the TPU part in PLA, because its undersized, and pressing the bearing in it would cause it to fail.&nbsp;Build Instructions:Drill holes After printing the Mainholder, you have to drill out the holes fot the rollers with a 4mm drill to later fit the screws. If the M4 screws fit, you can skip this step. The holes are made exactly 4mm to ensure the slicer makes 5 perimeter for strength. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_wmuhfakemqad.jpg"></figure>&nbsp;Heatinserts The M3x4mm brass inserts have to be placed at the sliding mechanism and on the hole where you want the bowdenswivel to sit later. (The parts are designed for 4mm deep inserts, but it's also possible to use 6mm ones like I did because I had too less 4mm ;) )<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_a60ufmrmawm1.jpg"></figure>&nbsp;Tension Springs:<blockquote>My prefered method is to use the rubber bands, even when the spring solution looks way nicer. But the springs tend to be too strong and overstretching them doesn't make them look nice.</blockquote>For the sliding mechanism you can use either tension springs or rubber bands. When using the springs, make sure that an empty spool will stay in place and don't get pushed out because the spring force is too strong. In case it's too strong you can widen the springs, but if they are too wide, a 140mm spool wont fit anymore.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_afhhdqdtdght.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_mmeizzw31hva.jpg"></figure>Use the M3x4mm screws to screw the springs in place&nbsp;Rubber Bands: Install the rubber bands like the springs. One per slot has enough force to hold the spool.<img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_s1ktst97rhlt.jpg"> Assembling the rollers: Press the bearing into rollerpart 1<img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_lpzxkn799hjr.jpg">Add superglue and slide the two halfes together<img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_8nkfcmbp9t4k.jpg"> <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_k17jdkrkcwv3.jpg"></figure>&nbsp;Installing the rollers: Insert the M4 hex nuts into the back of the Mainholder.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_3bgoc2k932xp.jpg"></figure>Add the Roller and the Spacer and screw them together with the M4x20 screw<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_vh6j1s4i5g84.jpg"></figure>&nbsp;Installing the PTFE Swivel After printing the swivel, make sure that the two parts can rotate. Press the PTFE tube into the swivel and screw it to the Mainholder<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_f2aek2jdswpi.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_xr3j0fuxpsfh.jpg"></figure>&nbsp;AMS Mounting: Connect the clamps with M4x16mm screws and M4 nuts loose to the Mainholder.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_n7cubyc4xkmj.jpg"></figure>Slide the whole assembly to your AMS and tighten the screws<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_1dmqtqzdpmt2.jpg"></figure>When the spoolholder with a full spool installed flexes too much you can also use double sided tape for better adhesion.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-12_vuzqa96gaaqw.jpg"></figure>&nbsp;CONNECTION:For connecting the AMS, the LP-Spoolholder or/and a filament dryer you can use my <a target="_blank" href="https://makerworld.com/en/models/74010" rel="nofollow noopener">3-Way Bowden Splitte</a>r:&nbsp;<figure class="image"><a href="https://makerworld.com/en/models/74010" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-11-25_580b350a182a5.jpg"></a></figure>&nbsp;AMS RISERIf you want to use the LPSH with an AMS - Riser, I recommend to check out the<a target="_blank" href="https://makerworld.com/en/models/86200" rel="nofollow noopener"> Mooser Project</a> by <a target="_blank" href="https://makerworld.com/en/u/2178842856" rel="nofollow noopener">Basti85</a>. It was designed to be fully compatible with the LPSH. His risers has already included the throughholes for the LPSH - Spoolholder. &nbsp;<figure class="image"><a href="https://makerworld.com/en/models/86200" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/334717/2023-12-09_9418658cdf1eb8.jpg"></a></figure>&nbsp;&nbsp;&nbsp;IMPORTANT INFO PART<blockquote>TIP: If the rollerslides are jamming from time to time, you can add some lubrication to the slider. I used the same silicon lube wich I use for the lead screws AMS: There seems to be different versions of the AMS. So before you print the clamps, check the rib size of your AMS. If you have 4 Ribs wich are 65mm - 86mm - 65mm appart, you can print the clamps like they are in the print profile. If you have 6 ribs wich are about 45 - 43mm appart you have to just print the "Clamp_small_18mm" at least 3 times Clearance Issue One user encountered too much clearance on his sliders wich leads to too much sagging of the spool. So I added three clearance test prints. The original "Mainholder" part comes with clearance 0.2mm. So print out the three clearance prints first and then decide wich "Mainholder" - version you want to print. For the sliders to work perfektly they must slide with ease (lube if necessary) but should not have too much wobble. Heat Inserts: There are 2 Types of M3 heat inserts. The one I used originally have ~5mm in diameter. If you are using the ones with 4mm outer diameter, there is a file called “holefix _4mm.stl" wich you can load together with the Mainholder.stl into the slicer. Just mark both files, pull them to your slicer and say "yes" when Bambu studio is asking if you want to load it as a single object. For those who want to go anyway with the rubber bands I added a "rubberplug" - part wich can be used instead of the heat inserts. There are also two versions, one for the original 5mm holes and one for the holes with the holefix for 4mm.&nbsp;Tension springs vs. rubber band My prefered method is to use the rubber bands, even when the spring solution looks way nicer. But the springs tend to be too strong and overstretching them doesn't make them look nice. UPDATE 21.11.23: - made the bowdenswivel stronger and added two different sizes 20mm and 30mm&nbsp;Update 31.12.23: - Holefix_4mm.stl for 4mm diameter heat inserts</blockquote>&nbsp;