jsfarmer

TripleGWorkshop

Updated! Based on user feedback minimum thickness has been increased to allow 4+ perimeters to help stop leaks.&nbsp;<figure class="image image_resized" style="width:80.65%;"><img src="https://makerworld.bblmw.com/makerworld/draft/123368/2023-10-27_g7q40hk7tdrz.jpg"></figure><figure class="image image_resized" style="width:79.89%;"><img src="https://makerworld.bblmw.com/makerworld/draft/123368/2023-10-27_qg778mua20o5.jpg"></figure><figure class="image image_resized" style="width:79.73%;"><img src="https://makerworld.bblmw.com/makerworld/draft/123368/2023-10-27_vpge5gk96mx0.jpg"></figure>

Plant Pot Apartments with drain

Zoe prints 

mkerhat

Just a cookie cutter. print with X-Y contour compensation 0.3mm

Westie cookie cutter

Fun stuff to print

bomas_ulz

Simply print 2x Bottom and 2x Top and insert rods. Diameter of the holes is 28.1mm. You need rods with a diameter of 28mm. I used old curtain rods made of wood with 27,76 mm diameter and I bought some wood rods in the hardware store with 28 mm diameter.&nbsp;Preparation:<ul><li>4 rods of 30 cm for the height</li><li>4 rods of desired length</li></ul>I first used 95 cm length, but siwtched to 120 cm length. &nbsp;Everything is plugged in, no glue required.&nbsp;Easily holds over 30 spools of filament. &nbsp;Printed with 3 walls/top/bottom and 15% gyroid infill in Prusament ASA. Maybe print just one part first and check if it fits your rods. Should work with other filaments, too.

Filament Spool Rack

Storage

3DPrintinGreece.gr

<h4>Summary</h4>after a lot of wishes we present the new smaller Test your 3D printer! version 2.new version 3 here: <a target="_blank" href="https://makerworld.com/en/models/54359#profileId-56081" rel="nofollow noopener">https://makerworld.com/en/models/54359#profileId-56081</a>&nbsp;new features<ul><li>saving 75% volume compared to version 1</li><li>only 2.52cm3. (Version 1, 2mm baseplate: 3.16cm3)</li><li>optimized 3D print font</li><li>higher resolution</li><li>wall thickness</li><li>this version is for 0.48mm extrusion width (more to come)</li></ul>This is a hard to print testfile! often you don't know if your printer is ready for complex files. with this file you have an easy option to check problematic printing/slicing stuff.does your printer challenge this ultimative part? check it out and get (almost) instant results.these test are included in this very tiny file:<ul><li>size: the object is 2x50x30mm (baseplate)</li><li>hole size: 3 holes (3/4/5mm)</li><li>Nut size: M4 Nut should fit perfectly</li><li>fine details: pyramide, cone, all numbers</li><li>rounded print: wave, half sphere</li><li>minimum distance & walls: 0.1/0.2/0.3/0.4/0.5/0.6/0.7mm</li><li>overhang: 25°/30°/35°/40°/45°</li><li>bridge print: 2/4/8/16/mm</li><li>surface: all the flat parts</li></ul>version 1 <h4>Instructions</h4><ul><li>infill: 33% infill or similar</li><li>extrusion width: 0.48mm</li><li>layerheight: 0.1mm</li><li>print time: about 30 minutes, depending on your printer & settings</li><li>raft: you can use a raft</li></ul>creation by <a target="_blank" href="https://www.thingiverse.com/ctrlV" rel="nofollow noopener">ctrlV</a> at <a target="_blank" href="https://www.thingiverse.com/thing:1019228" rel="nofollow noopener">Test your 3D printer! v2</a>

Test your 3D printer v2

Test prints

GuyH77

NOTICE: I have learnt a lot from this design. As a result I have created a new base ramp which is now released. This design is still valid and I will continue to maintain it. It serves it&#39;s purpose of the original designed goal. I designed this scoop to aid removal of larger debris that could interfere with the bed movement. My new design is an attempt to try and improve on the removal of very small bits of plastic. That is one criticism of this design. &nbsp;Alternative Design: Only tested by me so far: <a target="_blank" href="https://makerworld.com/en/models/507985#profileId-423740" rel="nofollow noopener">https://makerworld.com/en/models/507985#profileId-423740</a>&nbsp; - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -&nbsp;A simple two part print that forms a ramp at the front of your Bambu Lab printer making it easier to scoop out any stray bits of plastic.&nbsp;I printed standing up with a brim. The reason for this orientation is to get a nice smooth wall and strong clips. Split the stl to objects.&nbsp;The two halves should slide together with a snug fit. The clips help locate the scoop in the base of your printer.

Zoe prints

Fun stuff to print

Storage

Test prints

Printer Upgrades