Josh @ JRT3D.com

SShrimp

Inserts for the Medium Harbor Freight Organizer Bins (similar to my small and large bins). Inserts have a spot for labels. Versions for both vertical and horizontal orientations.This is inspired by the many of the other inserts that I have tried over the years; none of them exactly matched my needs so I finally designed my own version. I hope others find this useful.&nbsp;I printed all of these with a 0.4mm nozzle at 0.28mm layer height in PLA on my Bambu Labs P1S. I recommend ironing the top most layers especially if you want to write on the label. The 3x4 and 4x3 inserts may need a brim (otherwise the tend to fall over at about the 90% done mark.) All but the smallest inserts were printed successfully in “Sport” mode.&nbsp;Many different sizes. Files are named using the following pattern: A_B_CxD.stl: A: SB = Small Bin (Will be releasing versions for the Medium and Large Bins later) B: V = Vertical OR H = Horizontal C: number of Horizontal divisions/ColumnsD: number of Vertical divisions/Rows ex: SB_V_2x3.stl = Small Bin Insert, Vertical orientation, 2 Columns of 3 Rows. &nbsp;Please leave feedback and let me know if you have any issues (I have printed all of these on my P1S and tested and used them.)

Harbor Freight Medium Bin Inserts

Harbor Freight Parts Bin

Miguel M.

This is a Modular and multi-size tape dispenser.I first designed this as a single size (3/4in) non modular dispenser, held together with screws. The comment I got the most was : were are the other sizes?I refined the design, corrected a few mistakes in the files and made the whole thing fully customizable. You can now make this thing as wide as you want, holding as many rolls of any size you need.<h4>Versions</h4>My original screwed version is still available for those who like the look of the screws. This version is unfortunately not modular, but is now available in all sizes.The Glued version is the modular version available for tape rolls ½ in, ¾ in, 1 in and 2 in wide tape.Both version have holes on the bottom that accept 6x3mm round magnet. This dispenser was originally designed to go on my metal toolbox… use as many or as little magnets as you want/need (or none at all).The Spindles accept standard 3inch (inside diameter) rolls.There are 2 versions of the frames. The old version is wider, that is the only difference. They both work the same. the newer version uses less plastic keeps the total width of the dispenser reasonable and obviously saved printing time. I recommend the old wider version if you are printing a single 1/2 inch roll dispenser to make it more stable.I made a second version of the front and back 2 inch spacers that has triangular openings. Again this saves plastic, but it also makes it look a lot lighter, airier, open…. both versions function the exact same. Your choice.<h4>Printing</h4>I print My dispensers in PLA<ul><li>0.2mm layers</li><li>10% grid infill</li><li>2 perimeters for glued version</li><li>3 perimeters minimum for screwed version in order to have more material to drill and tap the holes.</li></ul>To print a dispenser you will need:<ul><li>1 LH frame</li><li>1 RH frame</li><li>1 Spindle (select a size)</li><li>2 pins</li><li>1 front Spacer (select same size as spindle for spacers)</li><li>1 Mid Spacer</li><li>1 back spacer</li></ul>If you are printing a multi-roll dispenser you will need:<ul><li>1 separator for each additional size you want to add</li><li>A set of spacers of the desired width</li><li>A spindle and 2 pins of the desired width.</li></ul>I included a clip that can be used to screw down the dispenser and keep it from moving if desired.I included STL for all versions of every partG-codes included for glued version (Modular)<h3>UPDATE!!</h3>I have uploaded a new model that lets you print a heavier base for this dispenser. The base replaces the spacers and can be filled with material of your choice to add weight.<a target="_blank" href="https://makerworld.com/en/models/492593" rel="nofollow noopener">https://makerworld.com/en/models/492593</a><h3>Assembly</h3>&nbsp;Screwed version:You will need 12x 6-32 screws 5/8 long (7/8 long for the old version frames) this length works with the ½ inch spacers, you can use longer screws for the wider versions if you wish to do so.Open the pilot holes in the spacers to 0.1065 (no.36 drill) and tap the spacers. You need to tap half way from each side of the spacers.You can also use 3mm screws approx. 16mm long ( 22mm for old/wider version of the frames) pre drill to 2.5 mm before tapping.Do not over torque the screws, this is just plastic and only needs light tightening.&nbsp;Glued versionThis version is a bit more user friendly.The parts in the glued version all have spherical registrations to align the holes. The important thing is to make sure that you cleanup the semi spheres from any stringing or imperfection before assembly. A quick light pass with sand paper is sometimes a good idea on the “male” spheres. The “female” spheres are usually pretty clean.I use C.A. glue to put everything together, I imagine epoxy would work very well also.I use clamps to press everything together and close all the gaps, and this works very well.I suggest doing a full gluing sections all at once to make sure every thing is glued square and will fit correctly with the following section. ( If you are going the modular route)If you don&#39;t have access to clamp, weights can certainly do the trick.Insert the pins in the spindle, they should go in tight. If not, a drop of glue will fix that. If too tight a little bit of sand paper should do the trick.You will need a ½ inch wide hacksaw blade. Cut to required length and insert in slot. Fit should be tight.I included a clip that can be used to screw down the dispenser and keep it from moving if desired. I could not think of an elegant way to add weight to this so this clip might help screw it down to keep it from moving around. A clamp also works well on the side of a work bench. Check back soon for a hook I&#39;m thinking of to lock it into a surface/shelf/bench in one quick motion…. will add it within a few days.Cabinet door adhesive rubber bumpers also work great to help keep it in place.&nbsp;That&#39;s a lot of info… don&#39;t hesitate to post a message if anything needs clarification.Thanks for downloading this if you did and don&#39;t forget to post your make! I&#39;m always curious to see what people do with the stuff I post. Constructive criticism always welcome.And If you have a minute, check out my other models!&nbsp;&nbsp;

Tape Dispenser, Multi-size/Modular

Office

dfreshkremer

I designed these brackets for storing/displaying DVD & Gaming Cases. I have tested DVDs, Xbox360, PS4, and Wii games. Any case that is the same size will work. I'm not positive about BlueRay cases, and Switch cases are too small. If there is enough interest, I will design a bracket to fit those different sizes - just shoot me a message or comment.&nbsp;You can screw these to the wall in a variety of orientations (will need to hit a stud and/or use drywall anchors). You can also print the Left and Right brackets to make it free-standing when attached together. The free-standing version can also be attached to the wall.  Each shelf/bracket will hold 8 DVD/Game cases. &nbsp;I have also added a little plug that can be printed and inserted into any of the unused screw-holes, if you feel the need.&nbsp;If you want to print the free-standing version, you will need to print a Right & Left bracket. The screw holes are off-set from each other, so you cannot attach two rights or two lefts together.  The holes are offset to make it easier to get a screwdriver in there to attach to the wall, and the offset screw holes also creates a stronger connection. &nbsp;&nbsp;