joelnobreneves

agepbiz

<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=jj3vnPYccS4"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/jj3vnPYccS4" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><p>Simple and clean looking Xbox Controller Stand</p><p>fits 8x3mm anti slip rubber pads (optional)</p><p>&nbsp;</p><p>Subscribe or follow me on:</p><p>Instagram: <a target="_blank" href="https://www.instagram.com/agepbiz/" rel="nofollow noopener">https://www.instagram.com/agepbiz/</a><br>YouTube: <a target="_blank" href="https://www.youtube.com/user/agepbiz" rel="nofollow noopener">https://www.youtube.com/user/agepbiz</a><br>Twitter: <a target="_blank" href="https://twitter.com/agepbiz" rel="nofollow noopener">https://twitter.com/agepbiz</a></p><p>&nbsp;</p><p>Printsettings: <br>No raft <br>Support Structures for best results where the rubber pads are<br>0,1-0,2mm layer height</p>

Minimalistic Xbox Controller Stand

interessante 

danospeti

<p>This is a remix of Cat Stretch by billyd. I used Meshmixer to reduce the mesh and create a voronoi pattern. I scaled it to 125% and printed it like that.</p><p> <a target="_blank" href="https://www.thingiverse.com/billyd" rel="nofollow noopener">https://www.thingiverse.com/billyd</a></p><h3>Print Settings</h3><p><strong>Resolution:</strong></p><p>0.2mm</p><p><br> </p><p><strong>Notes:</strong></p><p>You can add a raft or brim to help with adhesion. Adding supports to the underside of the belly can help as well, although many have printed it successfully without them.</p><p>Post-Printing:</p><p>Unfortunately, you will have to do a little bit of clean up at the undersides of the overhangs.</p>

Cat Stretch Voronoi Remix

decoração 

kungpaoshizi

<figure class="media"><div data-oembed-url="https://youtube.com/shorts/AqcyGq7_sfE"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=AqcyGq7_sfE">                        <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;">                          <iframe src="https://www.youtube.com/embed/AqcyGq7_sfE" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe>                        </div>                      </div></div></figure><p>Update: 1513 Hours: Haven&#39;t touched it since 1000… I do see buildup from time to time but the nozzle just knocks it off into the bin.</p><p>&nbsp;</p><p>Update:</p><p>Just crossed 1000 hours, so ya, I guess it works and doesn&#39;t need any intervention except maybe once per 400 hours or something… GG</p><p>&nbsp;</p><p>Update:</p><p>At around 550 hours I had one of the ptfe tubes come off. Put it back on and added a little dab of super glue on the end of each. At 790 hours and still going, zero interaction with it otherwise.</p><p>&nbsp;</p><p>Currently on about 400 hours with this now and haven&#39;t touched it. The problem with the stock is that it has a 90 degree angle wipe, but no side constrictions. So when it bends slightly to one side, it no longer has a flush 90 degree wipe.</p><p>I thought about a brush but it doesn&#39;t always stop the wisps. Along with a 90 degree wipe on anything, if it doesn&#39;t have side constraints, it&#39;s the same as the stock. This mimics a pinch and wipe effect which is far superior to anything other than Bambu&#39;s excellently forceful wipe on the back of the plate.</p><p>&nbsp;</p><p>I printed polycarbonate with .4 nozzle, 100% infill, had to print it at about 10-15 mm/s. and add &#34;G29.1 Z-0.01&#34; to the filament startup script. 40 threshold angle. Printed like the pic in slicer.</p><p>&nbsp;</p><p>Add ptfe to the little pillars post-print, use your smaller allen wrench that came with printer to push out the hole area. Then just replace the PTFE on the stock wiper with this, using same screw. Be careful when you screw it in, hold it steady with pliers and hold the black wiper end directly to the side of this piece. Otherwise you can strip the black spring holder hole.</p><p>&nbsp;</p><p>To Bambu Labs, I would be willing to license this design out to you for packing with the printer, it would be an honor and I would ask for only remarks. (and maybe .001% of every sale, then I can buy more coffee!)</p>

Kungpaoshizi Bambu X1 Carbon P1P Nozzle Wiper

super útil 

user_1381064641

<p>Push-Ups Handles Printed with PLA 50% infill</p>

Push-Ups Handles

3dprinting upgrades

uhltimate

<p>Create your own OTF (Out-The-Front) fidget knife with just three 3D printed parts! This compact design is perfect for restless hands, providing smooth OTF action for endless fidgeting fun. Watch my YouTube video for assembly instructions and start printing your own today!</p><p>&nbsp;</p><p><strong>Update:</strong></p><p>01.05.2024 - Added a guided Blade Version with a stronger locking mechanisms.</p><p>02.05.2024 - Added a comb Version as alternative.</p><p>&nbsp;</p><p><strong>Features:</strong></p><ul><li>Three easy-to-print parts</li><li>Smooth OTF action</li><li>Portable design for on-the-go fidgeting</li></ul><p><strong>Instructions:</strong></p><ol><li>Print the three parts.</li><li>Follow our assembly video.</li><li>Enjoy your custom OTF fidget knife!</li></ol><figure class="media"><div data-oembed-url="https://youtu.be/IQcEFHvocRc"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/IQcEFHvocRc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>

interessante

decoração

super útil

3dprinting upgrades

cool toys

interessante